Leviton 9866-B0W User manual

8" LED Downlight with Motion Sensor
Cat. No. 9866-B0W
INSTALLATION INSTRUCTIONS ENGLISH
DI-000-09866-05A
Flush-Mount with Bracket
WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER
at circuit breaker or fuse and test that power is off before wiring!
Product Overview
WARNINGS:
• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR
FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
CAUTIONS:
• For indoor applications only.
•READ AND SAVE THESE INSTRUCTIONS.
4. Tighten bracket until flush against the ceiling surface. DO NOT over
tighten. Over tightening will bend the bracket and make installation of
lamp difficult.
NOTE: Use 1/2 in. or 3/4 in. depending upon the depth of the ceiling box.
5.
a. Push light body up to bracket. Be sure to align the
sensor towards the door or entry point.
Sensor
b. Rotate light body clockwise to engage with
the bracket.
Bracket engaged.
2. Remove surface cover.1. Rotate bracket counter clockwise.
Switch 1: 30/180 seconds auto time-off options
Switch 2: Sensor Modes
• Daytime – Turns on lamp regardless of ambient light.
• Nighttime – Only turns lamp on when sensor detects motion and
there is no ambient light.
Switch 3: Sensor ON/OFF
• Turns off sensor so lamp can be used with a single pole switch.
CCT changeable
3000K: Soft white, yellowish
4000K: Cool white
5000K: Daylight, bright white
Motion Sensor
3. Wire the device as shown below.
NOTES:
• Run the main wire through the middle of the bracket.
• Wire Ground wire to green screw on the mounting bracket.
GROUND
GROUND
(Green)
(Green)
LINE
LINE
(Black)
(Black)
LOAD
LOAD
(Black)
(Black)
NEUTRAL
(White)
180ON
ON
12
s
30 OFF
s
3
Specifications
LED Consumption 18 Watts
Light Output 1440 Lumens
Lamp Color 3000k, 4000k, 5000k
Temperature -25 C < Ta < +40 C
Operating Voltage 120V +/- 10% @ 60Hz

© 2022 Leviton Mfg. Co., Inc.
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper
use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty
excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused,
opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including
merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a
particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment,
lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
For Technical Assistance Call: 1-800-824-3005 (U.S. Only) or 1-800-405-5320 (Canada Only) www.leviton.com
FCC COMPLIANCE
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada ULC to the attention of the Quality Assurance Department, 165
Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.
INDUSTRY CANADA COMPLIANCE
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Top View Side View
1.5
m
(5 ft)
0
1.5
m
(5 ft)
360°
CL
CL
0
2.4 m (8 ft)
1.5 m
(5 ft)
1.5 m
(5 ft)
0.9 m
(3 ft)
0.9 m
(3 ft)
0
Flush-Mount without Bracket
WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at
circuit breaker or fuse and test that power is off before wiring!
Sensor Coverage
1. Remove surface cover. 2. Wire the device as shown below.
NEUTRAL
(White)
(White)
LINE
LINE
(Black)
(Black)
LOAD
LOAD
(Black)
(Black)
3. Install the light body with two screws. 4. Install surface cover to light body. Ensure lock marks are aligned.
7. Install surface cover to light body. Ensure lock marks are aligned.6. Once the light body is in place install the two 1/2 in. screws to secure light
body to the bracket.
NOTE: Screws should go through light body then through the bracket.