Leviton 61A00-1 Mounting instructions

GLASSBREAK DETECTOR
Cat. No. 61A00-1
Installation Instructions and User’s Guide
INSTALLATION ENGLISH
DI-021-SY611-05AAR2253
For Technical Assistance Call: 800-824-3005- www.leviton.com DI-021-SY611-05AAR2253
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the attention of the Quality
Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.
WARNINGS AND CAUTIONS
• Read and understand all instructions. Follow all warnings and instructions marked
on the product.
• Do not use this product near water - e.g., near a tub, wash basin, kitchen sink or
laundry tub, in a wet basement, or near a swimming pool.
• Never push objects of any kind into this product through openings, as they may
touch dangerous voltages.
• SAVE THESE INSTRUCTIONS.
WARNINGS AND CAUTIONS
• Never install communications wiring or components during a lightning storm.
• Never install communications components in wet locations unless the components
are designed specifically for use in wet locations.
• Never touch uninsulated wires or terminals unless the wiring has been
disconnected at the network interface.
• Use caution when installing or modifying communications wiring or components.
DESCRIPTION
The 61A00-1 Wireless Glassbreak Detector is an omni-directional acoustic sensor and wireless transmitter that works with the Leviton 45A00-1 Wireless Receiver. It is used for
detecting the sound of breaking glass, providing 360º of coverage.
FEATURES:
• Wall or Ceiling Mount
• 360º coverage
• Powered by a 3 Volt Lithium battery
• Low Battery condition signal transmission
• Test mode for glass break coverage and RF signal
!
PROGRAM
SWITCH
SENSOR LED
MOUNTING
HOLE
MOUNTING
HOLE
Figure 1 – Model 61A00-1 Glassbreak Detector
INSTALLING THE BATTERY
The supplied 3 Volt Lithium Battery powers the unit.
To install or replace the battery:
• Remove the cover on the 61A00-1
• If applicable, remove the old battery
• Install a new battery according to polarity
Use care when installing the battery and observe
the correct polarity when the battery is inserted (See
Figure 1). Use only Panasonic Lithium CR2 batteries
for replacement.
WARNING! Battery may explode if mistreated. Do
not recharge, disassemble or dispose of in fire.
OPERATION
The 61A00-1 transmits the following event data:
Supervision: A periodic transmission every 60 minutes
to indicate detectors presence.
Alarm: Alarm transmission triggered by the sound of
breaking glass.
Battery Low: Whenever the battery reaches a preset
low level (2.4V) “Battery Low” signal will be sent with the next message
(i.e. Supervision, Alarm, etc.).
Enrolling the 61A00-1:
To enroll the 61A00-1, put the 45A00-1 Wireless Receiver in to Setup mode, advance to an unused address location, and then press and HOLD the program switch located on the 61A00-
1 circuit board (see Figure 1) for 1 second, and then release. The 61A00-1 will then send a series of transmissions and enroll the transmitter.
Refer to the Installation Instructions for the 45A00-1 for additional information.
Zone Configuration:
Avoid conguring the 61A00-1 to a 24-hour zone type (e.g. tamper, panic, etc.), so that the sensor is armed while the room is in use. Instead, consider conguring the zone type as night
interior or away interior. This will help prevent false alarms.
Note: The 61A00-1 may not consistently detect cracks in glass, or bullets which break through the glass. Glassbreak sensors should always be backed up by interior protection.
(61I00-1)
LEVITON LIMITED WARRANTY
Leviton warrants to the original consumer purchaser and not for the benet of anyone else that products manufactured by Leviton under the Leviton brand name (“Product”) will be free from defects
in material and workmanship for the time periods indicated below, whichever is shorter: • OmniPro II and Lumina Pro: three (3) years from installation or 42 months from manufacture date.
• OmniLT, Omni IIe, and Lumina: two (2) years from installation or 30 months from manufacture date. • Thermostats, Accessories: two (2) years from installation or 30 months from manufacture date.
• Batteries: Rechargeable batteries in products are warranted for ninety (90) days from date of purchase. Note: Primary (non-rechargeable) batteries shipped in products are not warranted.
Products with Windows®Operating Systems: During the warranty period, Leviton will restore corrupted operating systems to factory default at no charge, provided that the product has been used as
originally intended. Installation of non-Leviton software or modication of the operating system voids this warranty. Leviton’s obligation under this Limited Warranty is limited to the repair or replacement,
at Leviton’s option, of Product that fails due to defect in material or workmanship. Leviton reserves the right to replace product under this Limited Warranty with new or remanufactured product.
Leviton will not be responsible for labor costs of removal or reinstallation of Product. The repaired or replaced product is then warranted under the terms of this Limited Warranty for the remainder of
the Limited Warranty time period or ninety (90) days, whichever is longer. This Limited Warranty does not cover PC-based software products. Leviton is not responsible for conditions or applications
beyond Leviton’s control. Leviton is not responsible for issues related to improper installation, including failure to follow written Installation and operation instructions, normal wear and
tear, catastrophe, fault or negligence of the user or other problems external to the Product. To view complete warranty and instructions for returning product, please visit us at www.leviton.com.
COPYRIGHT AND TRADEMARK INFORMATION
This document and all its contents herein are subject to and protected by international copyright and other intellectual property rights and are the property of Leviton Manufacturing
Co., Inc, its subsidiaries, afliates and/or licensors. © 2013 Leviton Manufacturing Co., Inc. All rights reserved.
Use herein of third party trademarks, service marks, trade names, brand names and/or product names are for informational purposes only, are/may be the trademarks of their
respective owners; such use is not meant to imply affiliation, sponsorship, or endorsement.
No part of this document may be reproduced, transmitted or transcribed without the express written permission of Leviton Manufacturing Co., Inc.
WEB VERSION

For Technical Assistance Call: 800-824-3005 - www.leviton.com DI-021-SY611-05AAR2253© 2013 Leviton Mfg. Co., Inc.
SELECT MOUNTING LOCATION
Select a mounting location between 3’ and 20’ from plate, tempered, laminated, and wired glass; and between 3’ and 12’ from armor-coated glass. The 61A00-1 may be mounted on an
opposite wall, adjoining wall, or on the ceiling. Coverage is measured from the 61A00-1 to the point on the glass farthest from the sensor.
Optimal Glass Size: 1’ x 2’ (.3m x .6m) or larger
Optimal Glass thickness:
Plate: 3/32” to 1/4" (2.4mm to 6.4mm)
Tempered: 1/8” to 1/4" (3.2mm to 6.4mm)
Wired: 1/4” (6.4mm)
Laminated: 1/8” to 1/4" (3.2mm to 6.4mm)
It is advisable to avoid the following locations:
• Noisy rooms with multiple noise sources (e.g. kitchens, garages, home theaters, small bathrooms, etc.)
• Small rooms (smaller that 10’ x 10’), hallways, and stairwells
• Mounted in the corner of a room
• Rooms lined with sound deadening materials
• Rooms with closed wooden window coverings
• Humid areas
• Outdoors
The 61A00-1 performs best:
• At least 4’ from noise sources (televisions, speakers, etc.)
• When the sensor is in the direct line of sight of all glass to be protected
MOUNTING THE DETECTOR
The 61A00-1 can be mounted to a wall or ceiling using the mounting holes (see Figure 1) with the supplied hardware. There is no front or back, up or down orientation of the sensor
required.
Wall Mounting:
The best location for mounting the sensor is on the opposite wall, within the sensors range, and within the line of sight of the glass to be protected. The ceiling and adjoining (side)
walls are also good locations.
Ceiling Mounting:
Mount the 61A00-1 in any type ceiling within the direct line of sight of the glass to be protected. A position of 6’ – 10’ into the room provides better detection.
TEST MODE
To test the 61A00-1, we recommend the use of a Sentrol 5709C hand-held tester. In normal mode, the LED on the 61A00-1 does not blink unless it hears a loud sound. It will not trip
(cause an alarm condition) to the tester unless the tester is held next to the sensor.
To put the 61A00-1 into test mode, hold the tester’s speaker directly over the sensor and re the tester. When in test mode, the LED on the sensor will continually blink for one minute.
Every time the tester is red at the sensor, the test mode is extended for 1 minute. The 61A00-1 will automatically exit test mode approximately 1 minute after the last test re from the
tester.
NOTE: Every time the 61A00-1 trips (causes an alarm condition), the sensor goes into test mode for 1 minute.
Testing the Sensor:
Holding the tester near the surface of the glass to be protected, aim the tester at the 61A00-1 and press the test button. If window coverings are present, hold the tester behind the
closed window covering (not recommended for use with heavy or lined drapes).
When the sensor is tripped (in an alarm condition), the LED on the 61A00-1 will illuminate solid for about 4 seconds. If the LED does not illuminate solid, but just continues blinking,
reposition the sensor.
Hand Clap Test:
The 61A00-1 can be checked by at any time while in normal mode by clapping loudly under the sensor. The LED will blink two times but the 61A00-1 will not trip. This visually veries
that there is power to the unit and the microphone and circuit board are functioning.
SPECIFICATIONS
Housing material: Flame retardant ABS
Alarm duration: 4 seconds
Microphone: Omni-directional electret
Temperature range: 14º F to 120º F (-10º C to 50º C)
Dimensions: 4.24” W x 3.13” H x 1.7” D
Data Protocol: Leviton
Supervision Timing: 60 minutes
Battery Lithium: 3V Type: CR123A
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
WEB VERSION