Leviton Intellect Solo Sensor ZLS05-ILW User manual

Solo SensorTM
Cat. No. ZLS05-ILW
DI-000-ZLS05-05A
WARNINGS
•
TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!
• For indoor applications only.
• If you are unsure about any part of these instructions, consult an electrician.
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
ENGLISH
INSTALLATION INSTRUCTIONS
DESCRIPTION
• ZLS05-ILW Solo Sensor™ designed to be mounted directly into light fixtures for occupancy and daylight harvesting control. Intended for use with 0-10V dim-to-off drivers, this
sensor uses Passive Infrared (PIR) detection technology to monitor a room for occupancy through a segmented lens. This specialized lens divides the field-of-view into sensor
zones. When a person passes into or out of a sensor zone, the sensor detects motion and switches the lights ON.
• The sensor is also designed for Daylight Harvesting Control and can maintain the desired lux level by regulating light output according to the intensity of natural light in the sensor
zone. The lights will remain ON as long as there is an occupant moving through the sensor zones unless sufficient ambient light is present.
• Product settings can be manually adjusted using the DIP switches or optional IR remote (ZLS0R-RA1). Adjustable settings include sensor sensitivity, hold time,
daylight harvesting lux level, stand-by level and stand-by time.
• ZLS05 Solo Sensor provides a 360° field-of-view with a maximum coverage area of approximately 700 square feet. The maximum sensing distance is 15 feet from center of
sensor. An optional IR remote (Cat. No. ZLS0R-RA1) can be used to adjust lighting levels up or down per the user’s preferences.
NOTES:
• Requires a 0-10V dim-to-off driver
• Designed to install directly in fixture
• Mounting height of 2.5m-3m (8-10ft);
• Max mounting height of 4m (13ft) but may limit Field-of-View
• Configure DIP switch settings prior to installation into fixture
• Use provided plastic lock nut to secure sensor tightly in place
INSTALLATION
FOR OPTIMAL PERFORMANCE:
The ZLS05 Solo Sensor lens establishes dozens of zones of detection. The sensor is sensitive to the heat emitted by the human body. To trigger the sensor, the source of heat
must move from one zone of detection to another. The device is most effective in sensing motion across its field-of-view, and less effective sensing motion towards or away from
its field-of-view. Keep this in mind when selecting the installation location. Note that occupancy sensors respond to rapid changes in temperature, so care should be taken not to
mount the device near a climate control source (i.e. radiators, air exchanges, and air conditioners). Hot or cold drafts will look like body motion to the device and will trigger it if the
unit is mounted too close. It is recommended to mount the Occupancy Sensor at least 6 ft. away from a climate control source. In addition, it is also recommended NOT to mount
the Occupancy Sensor directly under a large light source. Large wattage bulbs (greater than 100W incandescent) give off a lot of heat and switching the bulb causes a temperature
change that can be detected by the device. Mount the Occupancy Sensor at least 6 ft. away from large bulbs. If it necessary to mount the device closer, lower the wattage of the
bulb directly overhead. For applications involving daylighting harvesting, please ensure sensor and fixture are installed in locations that receive sufficient ambient light.
Specifications
Input Voltage/Frequency 10-24VDC, >50mA
Input Current 25mA sinking current
Purpose of Control Energy Management Equipment
IP Rating IP20
Operating Temperature -20°C to 70°C (-4F - 158F)
Storage Temperature -20°C to 85°C (-4F - 185F)
WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit
breaker or fuse and test that power is off before wiring!
1. Adjust sensor operations by using DIP switches. Factory settings default to:
• Sensitivity: 100%
• Hold time: 10 seconds
• Dimming level: 30%
• Dimming time: 60 minutes
2. Position sensor correctly and tighten plastic lock nut.
3. Remove 3/4 in. of insulation from each of the wires and connect per wiring diagram.
4. After all connections have been made, ensure that all wire connectors are firmly
attached and there is no exposed wire.
5. Restore power to the circuit and verify locator LED lights are ON.
CLASS 2 WIRING:
For 0-10V Control Wiring: connect the Violet wire to the + 0-10V line and the Gray wire to the 0-10V
common using Class 1 or Class 2 wiring methods as indicated in these instructions, ballast/fixture/
driver instructions or ballast/fixture/driver label markings. Observe all requirements of any authority
having jurisdiction with respect to wire type, sleeving, isolation methods, and the like.
VIOLET (DIM+) GRAY (DIM-) BROWN (VCC)
Dimming
Driver LED
L
N
YELLOW (GND)
Coverage Side View
12’12’
10’
7’7’ 5’5’ 3’3’ 0’
0’
Minor Motion
Coverage Top View
30’
15’15’
15’
15’
10’
10’
5’
5’
0’
10’10’ 5’5’ 0’
Major Motion
The ZLS05 Solo Sensor is designed to operate per user settings. An optional IR remote
(Cat. No. ZLS0R-RA1) can be used to configure the sensor and adjust lighting levels up
or down per the user’s preferences.
OPERATION
Intellect®
WEB VERSION

FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada ULC to the attention of the Quality Assurance Department, 165
Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper
use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty
excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused,
opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including
merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a
particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment,
lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
© 2020 Leviton Mfg. Co., Inc.
IC STATEMENT
This Class B digital apparatus complies with Canadian CAN ICES-3(B)/NMB-3(B). This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause
undesired operation of the device.
To ensure compliance with FCC’s and ISED Canada’s RF exposure requirements this device must be installed to provide a minimum of 20cm between the device and people.
FCC SUPPLIER'S DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Responsible Party: Leviton Manufacturing, Inc., 221 N Service Road, Melville, NY, http://www.Leviton.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
CONFIGURATION
TASK LIGHT LEVEL
Set desired task light level. The built-in daylight sensor will measure the ambient
daylight level and calculate how much artificial light us needed to maintain the task light
level.
OCCUPIED TIMEOUT SETTING
Set desired timeout period. Light will remain on until timeout expires. Any motion
detected during this time will restart the timeout period.
STAND-BY LIGHT LEVEL SETTING
Set desired stand-by level. After the occupied timeout has expired, light will dim to the
stand-by level.
STAND-BY TIME SETTING
Set desired stand-by time. Light will remain at stand-by level until time period expires
or motion is detected. Carefully adjust and refine DIP switch settings on all associated
sensors. If the task light level is adjusted using the remote control, the sensor will
default to remote control unless the DIP switches are reset.
Task Light Level: 1, 2
ON
OFF
ON
OFF
Time: 3,4,5
Task Light Level
12%
70%
80%
90%
100%
Time
345
10 seconds
30 seconds
1 minute
3 minutes
5 minutes
10 minutes
15 minutes
30 minutes
Stand-By Time
78
1 minute
30 minutes
60 minutes
+ '
Stand-By Level: 6
ON
OFF
ON
OFF
Stand-By Time: 7,8
Stand-By Level
6%
20%
50%
For Technical Assistance Call: 1-800-824-3005 (USA Only) or 1-800-405-5320 (Canada Only) www.leviton.com
FCC STATEMENT
Any changes or modifications not expressly approved by Leviton Manufacturing Co., could void the user’s authority to operate the equipment.
WEB VERSION