LG-Ericsson LDP-7024D User manual

Important Safety Information

Important Safety Information

Important Safety Information

LDP
7000 Series Model 7016D & 7024D
Getting Started
LDP
-
7000
Series
,
Model
7016D
&
7024D
LDP-7016D/7024D are advanced, user-friendly digital keysets, offering the convenience
of 3 soft buttons and a navigation key.
• Features
-.Trendy and Stylish LDP Family design
()
-.Multi Level 3 Line LCD
(
3 x 24
)
-.16 or 24 Flexible buttons with dual-color LED’s
-.Additional Device Port (ADP) for SLT or FAX
-.Call Log Feature
-.Call Recording Feature –7024D only (Optional USB Module).
-.Hands-Free Solution –7024D only (Optional Blue- Tooth Module).
-.Wall Mountable (Bracket O
p
tional)
LDP
-
7016D
LDP
-
7016D
LDP-7024D
1

Input / Output Devices and Buttons
Getting Started
Input
/
Output
Devices
and
Buttons
Handset Visual Ringing LED
110
Earphone-Jack Socket
(Ear/Mic Mode)
Speaker
Speed Button
Trans/Pgm Button
Flexible Button (Loop Button)
Call back Button
2
3
4
11
12
13
Dnd/Fwd Button
Speaker Button
Hold/Save Button
V
olume Button
Hands-free Microphone
Menu Button
5
6
7
14
15
16
3 Soft Button
LCD Display
Phonebook Button
(Same operate as ‘Speed’)
8
9
17
2

Getting Started
Used for handset call.
Used to connect optional headset to the phone.
Outputs tones and voice.
Used to access speed dialing, speed programming, save number redial,
and last number redial.
Handset
Earphone-Jack Socket
Speaker
Speed Button
1
2
3
4
The DND (Do Not Disturb) feature blocks all incoming calls. When DND
is active, the red LED in this button is illuminated.
It is also used to activate call forward, e.g. to another station or
voicemail. When call forward is activated, the red LED flashes.
Speaker toggles the speakerphone state, and the red LED is
illuminated when the speakerphone is active.
DND/Fwd Button
Speaker Button
5
6
This button is used to put a call on hold or save information when
programming.
Used in conjunction with fixed and flexible features, and the function
changes in relation to call progress, as indicated on the LCD display.
Displays information about telephone status, dialing directories,and test
message information.
Hold/Save Button
3 Soft Buttons
LCD Display
7
8
9
Illuminates when the phone is ringing.
This button is used to initiate a call transfer (TRS) or to enter
programming mode (PGM)
Some flexible buttons are pre-programmed in the system for line
appearances, loop functions etc. The remaining flexible buttons can be
Visual Ringing LED
Trans/PGM Button
Flexible Button
10
11
12
appearances,
loop
functions
etc.
The
remaining
flexible
buttons
can
be
user-programmed.
A station can initiate a call back request to a busy station. Once that
station becomes idle, the initiating station is signaled.
The volume button adjusts the audio levels for ringing, handset and
speakerphone functions.
Microphone
is
used
for
hands
free
speakerphone
function
Call back Button
Volume Button
Hands
-
free Microphone
13
14
15
Microphone
is
used
for
hands
-
free
speakerphone
function
.
The menu button is used to move to the desired option(Dial, MSG,
Program), and to select the next screen when indicated by an arrow on
the LCD display.
Used to access speed dialing, save number redial, and last number
redial, and to access flexible button programming.
Hands
-
free
Microphone
Menu Button
Phonebook Button
15
16
17
3

Cable Connection
Getting Started
Cable
Connection
BC
A
A
Cable connections
A
-
Connect the telephone cord (curly cord) to the handset and the other end to the
A
Connect
the
telephone
cord
(curly
cord)
to
the
handset
and
the
other
end
to
the
handset jack at the bottom of the telephone.
B - Connect the line cable to the port at the bottom of telephone and the other end to the
wall socket.
C
-
Connect the Headphone to the headphone jack on the left side of the telephone.
C
Connect
the
Headphone
to
the
headphone
jack
on
the
left
side
of
the
telephone.
(As viewed from the front.)
4

ADP (Additional Device Port)
Getting Started
ADP
(Additional
Device
Port)
5

ADP (Additional Device Port)
Getting Started
ADP
(Additional
Device
Port)
6

1 Placing a Call
Getting Started
1
.
Placing
a
Call
ICM Line
Lift handset
▶
Enter the extension number
talk▶
or
CO Line
Dial 9 or select
CO line flexible
button.
CO
Line
▶talk
▶
or ▶
2A i Otid Cll
Lift handset Enter the desired phone number
2
.
A
nswer
i
ng an
O
u
t
s
id
e
C
a
ll
ICM Line
Lift handset
or ▶talk
CO Line
or ▶talk
Press flashing
CO line button or
loop key. ▶
Lift handset
7

3 Soft Button
3 Soft Buttons & Navigation Button
The 3 Soft Buttons are located on the bottom of the LCD display. The function of each button
changes, subject to call status and progress. The current functions are displayed on the LCD
screen, directly above each button. For example, if the user calls a busy extension, busy tone will
be heard and the busy status displayed. The LCD screen will display the busy message along with
the different options available - “Call Back”, “Flash” , “Call Wait” , “Camp On” and “Pilot Hunt”. By
f
3
Soft
Button
pressing the relevant button the desired
f
eature is activated.
BUSY : 100
12 OCT 09 12:00 pm BUSY : 100
12 OCT 09 12:00 pm
C-BACK FLASH C-WAIT CAMPON P-HUNT
Navigation Button
In some instances, more than 3 current functions are available to the user, and this is indicated by
the appearance of a left ()orright() arrow in the LCD screen, (see below). By pressing the
navigation
key
(located
below
the
volume
button),
in
the
direction
corresponding
to
the
arrow,
any
navigation
key
(located
below
the
volume
button),
in
the
direction
corresponding
to
the
arrow,
any
additional functions will be displayed.
STATION 100 (T)
12 OCT 09 12:00
p
m
p
LOG DIR REDIAL
STATION 100 (T)
12 OCT 09 12:00 pm
PICKUP FWD DND
8

B
y
p
ressin
g
one of the 3 soft buttons
y
ou are able to select the indicated function. Fo
r
instance
,
if
Basic Function
y
pg
y
,
you want to select call pickup (as shown below), press the first button on the left. If there are more
than three functions available at any point, an arrow will be displayed on the LCD display. Use the
navigation key to move the next or previous screen to display additional functions.
Sf
C
1. Idle
3
S
o
f
t Buttons are located below the L
C
D display.
LOG : press to check call log information
DIR : press to use Directory
Service.(Station/System Speed)
REDIAL :
p
ress to redial last number called.
STATION 100 (T)
12 OCT 09 12:00 pm
LOG DIR REDIAL
p
PICKUP : press to pickup a call ringing within the
same pickup group.
FWD : Press the [FWD] button to forward calls to
another station, Voicemail etc.
STATION 100 (T)
12 OCT 09 12:00 pm
PICKUP FWD DND
1.1 Pickup
A station can pickup a call ringing to an unattended station within the same pickup group by using
DND : press the [DND] to set Do Not Disturb.
the pickup procedure.
＊Refer to iPECS-MG system programming manual.
Press [PICKUP] button.
STATION 100 (T)
12 OCT 09 12:00 pm

PICKUP
FWD DND
CALL TO STA 104 PICKED UP
CALLER 101 12:00 pm
TRANS CONF MUTE

Talk

PICKUP
FWD
DND
TRANS
CONF
MUTE

9

1 2 Conference
Basic Function
1
.
2
Conference
CALL TO 100
12 OCT 09 12:00 pm
MSG FLASH
Dial the desired station number.
(e.g.100)
Station 100 answers the call.
CONNECT TO 100
FEB 01 04 05:34 pm
TRANS CONF MUTE
Press [CONF] button.
CALL TO 104
12 OCT 09 12:00 pm
CONF(R) FLASH
Dial the phone number of the next desired station.
(e.g.104)
CONNECT TO 104
12 OCT 09 12:00 pm
CONF(A) CONF(R) FLASH
Station 104 answers the call.
Press the [CONF (A)]
P th [CONF (R)] O Di l th
DN 100
12 OCT 09 12:00 pm
LOG DIR CONF(R)
P
ress
th
e
[CONF
(R)]
.
O
r
Di
a
l
ano
th
er
station.
CONFERENCE(003/003)
12 OCT 09 12:00 pm
MUTE CONF FLASH
A 3-party conference is now established.
10

13Redial
Basic Function
1
.
3
Redial
Press the [REDIAL] button.
STATION 100 (T)
12 OCT 09 12:00 pm
The last number dialed on an external call is automatically saved in the LAST Number&
Redial (LNR) buffer Or Call Log Buffer.
123456789
26/12 16:00
Press [SEND] button to make call.
12
OCT
09
12:00
pm
LOG DIR REDIAL 
26/12
16:00
EXIT SEND
123456789
LINE 008 00:00:10
TRANS CONF MUTE

Talk
TRANS
CONF
MUTE

2. Off Hook
LOG : press to check call log information
DIR
: press to use Directory
STATION 100 (T)
12 OCT 09 12 00
DIR
:
press
to
use
Directory
Service.(Station/System Speed)
REDIAL : press to redial last number called.
12
OCT
09
12
:
00
pm
LOG DIR REDIAL 
PICKUP : press to pickup a call ringing within the
same pickup group
STATION 100 (T)
12 OCT 09 12 00
same
pickup
group
.
FWD : Press the [FWD] button to forward calls to
another station, Voicemail etc.
DND : press the [DND] to set Do Not Disturb.
12
OCT
09
12
:
00
pm
PICKUP FWD DND
3. Intercom Dialing
STATION 100 (T)
12 OCT 09 12:00 pm
LOG FLASH
LOG : press to check call log information
FLASH : If you wish to terminate an ICM call and make
another call, press [FLASH] to re-seize dial
t
t
one.
11

4. Intercom Ring Back
Basic Function
STATION 100 (T)
12 OCT 09 12:00 pm
MSG FLASH
MSG : Press to leave a your station number or
message.
FLASH : Press to disconnect the line and re-seize.
5 Intercom Busy
5
.
Intercom
Busy
BUSY : 100
12 OCT 09 12:00 pm
C-BACK FLASH 
C-BACK : Press to leave your station number or
message.
FLASH : Press to disconnect the line and re-seize.
BUSY : 100
12 OCT 09 12:00 pm
C-WAIT CAMPON P-HUNT
C-WAIT : Press to make call waiting.
CAMPON : Press to send a camp-on tone to a busy
station (indicating that they have a call
waiting).
P
-
HUNT
: Press to make Pilot hunt group call
6. Intercom Do Not Disturb
DO NOT DISTURB 101
12 OCT 09 12:00 pm
MSG FLASH

MSG : Press leave a call back request or message.
FLASH : Press to disconnect the line and re-seize.
P
-
HUNT
:
Press
to
make
Pilot
hunt
group
call
MSG
FLASH

DO NOT DISTURB 101
12 OCT 09 12:00 pm
P-HUNT
P-HUNT : Press to make Pilot hunt group call
7. Intercom Dialing Error
INVALID
12
OC
T
09
12:
00
p
mFLASH : Press to disconnect the line and re-seize.
OC 09 00 p
FLASH
8. Intercom Receiving
CALL FROM 104
HOLD
: Press to make a HOLD call
CALL
FROM
104
12 OCT 09 12:00 pm
HOLD DND
HOLD
:
Press
to
make
a
HOLD
call
DND : Press to make DND
12

9. Intercom Talk
Basic Function
CALL FROM 104
12 OCT 09 12:00 pm
TRANS CONF MUTE
TRANS : Press to transfer an incoming call to another
station.
CONF : Press to initiate a conference call.
MUTE : Press to mute the handset, speakerphone,
or headset microphone. Press the [SPEAK]
button to re- activate microphone.
10 CO Dialing
CALL FROM 104
12 OCT 09 12:00 pm
ACNR FLASH PRIVACY
ACNR : Press to set automatic called number redial.
FLASH : Press to disconnect the line and re-seize.
PRIVACY : Press to use privacy mode.
10
.
CO
Dialing
STATION 100 (T)
Press programmed flexible button for CO
10.1 Manual Dialing
The following CO access codes ‘9’, individual CO access code can be changed by Admin
Programming 115 depending on the user’s needs.
STATION
100
(T)
LINE 08 00:00:03
TRANS CONF MUTE
Press
programmed
flexible
button
for
CO
.
(CO can be accessed by dialing CO access code 9 or
individual CO access code)
Dial telephone number.
10.2 Speed Dialing
SPD_NO LAST(*) SAVE(#)
BACK SEARCH ADD
Press [SPEED] button.
Press SEARCH to search speed dial by name
>ABC : 9123456789
Dial number to seach name
>ABC
:
9123456789
[SEARCH] :
EDIT ERASE
Dial
number
to
seach
name
EDIT : Press EDIT to edit speed bin
ERASE : Press ERASE to delete speed bin
>ABC : 9123456789
[SEARCH] :
BACK: Press BACK to go to privious menu
SEND
: Press SEND to make a call
11. CO Line Busy
FLASH
If o ish to terminate a call and make
[SEARCH]
:
BACK SEND EXIT
SEND
:
Press
SEND
to
make
a
call
EXIT : Press EXIT to exit Speed Menu
BUSY
FLASH
FLASH
:
If
y
o
u w
ish
to
terminate
a
call
and
make
another call, press [FLASH] to re-seize dial
tone.
13

12 CO Talk
Basic Function
12
.
CO
Talk
123456789
LINE 08 00:00:03
TRANS CONF MUTE
TRANS : Press to transfer a call to another station.
CONF : Press to initiate a conference call.
MUTE : Press to mute the handset, speakerphone, or
headset microphone. Press the [SPEAK]
button to re
-
activate microphone.
123456789 ACNR : Press to set automatic called number redial.
FLASH
: Press to disconnect the line and re
seize
button
to
re
activate
microphone.
LINE 08 00:00:03
ACNR FLASH PRIVACY
FLASH
:
Press
to
disconnect
the
line
and
re
-
seize
.
PRIVACY : Press to use privacy mode
13. Paging
Y
i
t
f
th
tti
d/
tl
k
St ti
Y
ou may rece
i
ve announcemen
t
s
f
rom o
th
er s
t
a
ti
ons an
d/
or ex
t
erna
l
spea
k
ers.
St
a
ti
ons
are assigned to one or more of the Internal Page Zones. The system has one External
Page Zones that are connected to external speakers.
PAGE FROM STA 103
12 OCT 09 12:00 pm MEET ME : Press to answer a paging request.
MEET ME
14. Call Forward
ENTER FORWARD TYPE Press [ SPEAKER ] button.
( 0 – 4 , # ) Press [ DND/FWD ] button.
Enter forward type.
0 : Remote Forward
1 : Unconditional Forward
2 : Busy Forward
3 : No Answer Forward
4 : Busy/No Answer Forward
# : Cancel Forward
Enter Forward destination
STA : station number,
HUNT : Hunt group,
14
V
MIB : VMIB Access code
Telephone Number : Telephone number with CO
Access code

15 FLEXIBLE BUTTON PROGRAM
Basic Function
15
.
FLEXIBLE
BUTTON
PROGRAM
•Pressthe[TRANS/PGM] button
• Press the flexible button to be programmed
• Enter the desired feature code below table.
•Pressthe[HOLD/SAVE] button to save.
*) The following Numbering Plan code can be changed by Admin Programming
PGM 113~115 depending on the user’s needs.
EMPTY NUM (1) :
STA : station number
NUM (1) / FIX(2) / DEL(0)
STA
:
station
number
,
HUNT : Hunt group.
CO Number
Feature code.
Telephone Number : Telephone number with CO
Access code
FIX (2) : Fixed button
(REDIAL/CONFERENCE/MUTE/FLASH/PTT)
DEL(0) : Delete Flexible button
16 PARK A CA AND RETRIEVE A PARKED CA
16
.
PARK
A
CA
LL
AND
RETRIEVE
A
PARKED
CA
LL
• To park a call,
Press Call Park Location Code (541) and dial the Park Location(01-49).
A call can be parked in a parking location and the call will be retrieved by dialing the location
number. (The call can be picked up by other extension.)
• To retrieve a parked call at any station,
Press Call Park Location Code (541)
Dial the Park Location (01-49).
•Pressthe[TRANS/PGM] button
• Dial “1 2”
• Enter your name (see Entering character table in page 58)
17. NAME DISPLAY ON MY PHONE
Name can be displayed instead of station number.
15
For example to enter the name “JOHN”
•Pressthe[HOLD/SAVE] button

18 CALL BACK
Basic Function
18
.
CALL
BACK
When a called station is in busy, call back can be requested.
BUSY : 100
12 OCT 09 12:00 pm
C-BACK FLASH 
When a called station is in busy, camp-on can be requested.
19. CAMP ON
BUSY : 100
12 OCT 09 12:00 pm
C-WAIT CAMPON P-HUNT
To answer the second(call waiting) call,
press flashing [HOLD/SAVE] button.
CALL WAIT FROM 105
05 MAR 06 09:51
TRAN
S
CO
NF M
U
TE
20. VOICE OVER
TRANS
CONF
MUTE

CONNECT TO 101
05 MAR 06 09:51 Whenever [HOLD/SAVE] button is pressed,
call will be switched between first and second
call
TRANS CONF MUTE
call
.
16

Call Log
The call log feature enables the LDP phone user to view a log of the last(100) incoming and
outgoing calls. The user can scroll through the list of numbers stored, select the number
Press the [Call Log] button.
: Incoming Call
Call Log Button PGM : Call Log Feature code (685)
outgoing
calls.
The
user
can
scroll
through
the
list
of
numbers
stored,
select
the
number
and activate a redial to that number.
: Outgoing Call
M : Missed Call
01 9123456789
02 M 9987654321
SEND SELECT EXIT
SEND : Press to make a call with selected list.
SELECT : Press to see the detailed information
of list.
01

9123456789
EXIT : Press to exit the call log menu.
DEL SEL
Ptdltthltdllllit
01

9123456789
02 M 9987654321
DEL_SEL DEL_ALL
DEL
_
SEL
:
P
ress
t
o
d
e
l
e
t
e
th
e se
l
ec
t
e
d
ca
ll
l
og
li
s
t
.
DEL_ALL : Press to delete all call log list
17