Life Fitness CLSX Installation guide

INTEGRITY AND CLUB SERIES CROSS-TRAINERS
CLSX & CSX ASSEMBLY INSTRUCTIONS
M051-00K61-C131

Congratulation ...
and welcome to the world of
The following Component ist and the step-by-step assembly procedures have been developed to
make the set-up of the Cross-Trainer as quick and easy as possible.
Please take special note of the following important points prior to choosing a location and beginning
assembly of the Cross-Trainer.
1

IMPORTANT SAFET INSTRUCTIONS!
âDO NOT locate the Cross-Trainer outdoors, near swimming pools, or in areas of high
humidity.
âDO NOT operate your Cross-Trainer if it has been dropped, damaged, or even partially
immersed in water. If this occurs, contact Life Fitness Customer Support Services at
the number in the Operation Manual.
âDO NOT locate the Cross-Trainer any closer than 30 inches (76 cm) to a television
set.
âDO NOT locate additional Cross-Trainers any closer than 42 inches (107 cm) from
center to center to avoid interference (cross talk) between heart rate monitors.
âDO keep the area around your Cross-Trainer clear of any obstructions, including walls
and furniture. Ensure that there is at least a 12 inch (30 cm) clearance in front of the
Cross-Trainer.
âDO verify the contents of the delivery carton against the accompanying parts list prior
to setting the cartons and shipping material aside. If any parts are missing, contact
Life Fitness Customer Support Service at the number listed in the operation manual.
Save the shipping cartons in case of return.
âDO read the entire Operation Manual prior to attempting to operate this machine as
this is essential for proper use.
CONSIGNES DE SECURITE IMPORTANTES!
âNE placez pas l'appareil à l'extérieur, près d'une piscine ou dans un endroit très
humide.
âNE faites pas fonctionner l'appareil s'il est tombé, s'il a été endommagé ou s'il a été
partiellement plongé dans l'eau. Si cela s'est produit, contactez le service après-vente
de life fitness au numéro fourni dans le manuel d'utilisation.
âNE placez pas l'appareil à moins de 76 cm d'un poste de télévision.
âNE placez pas d'autres appareils du même type à proximité. Un espace d'au moins
107 cm doit être observé entre les parties centrales de deux appareils afin d'éviter les
interférences entre les contrôleurs de rythme cardiaque.
âMAINTENEZ la zone autour de l'appareil libre de toute obstruction, y compris murs et
meubles. Veillez à laisser un dégagement d'au moins 30 cm devant l'appareil.
âVÉRIFIEZ si l'emballage contient toutes les pièces de la liste jointe avant de le mettre
de côté. Si des pièces sont absentes, contactez le service après-vente de life fitness
au numéro indiqué dans le manuel d'utilisation. Conservez l'emballage au cas où vous
devriez renvoyer l'appareil.
âLISEZ le manuel de l'utilisateur tout entier avant d'essayer de faire fonctionner cet
appareil. Ceci est indispensable à son utilisation correcte.
2

COMPONENT LIST
# Part Description Qty. # Part Description Qty.
1
Hex Socket Head Cap Screw
3/8-16 X 1”
0017-00101-1645
8 2
Phillips Pan Head Screw
#8-18 X 3/4”
0017-00101-1744
4
3
Phillips Pan Head Pointed Screw
#8-18 X 3/4”
0017- 00101-1242
18 4 Console Assembly
(shipped separately) 1
5 Front Monocolumn Cover 1 6 Back Monocolumn Cover 1
7 Console Support Assembly 1 8 Flat Washer
0017-00104-0192 2
9 eft Front Cover 1 10 Right Front Cover 1
11 eft User Arm Assembly 1 12 Right User Arm Assembly 1
13 Front Rocker Cover 2 14 Back Rocker Cover 2
17 Accessory Tray 1 18 Internal Tooth ock Washer
0017-00104-0450 6
19 Cap: Console Support 1 20 Grommet
0017-00042-0754 4
21 Cap Screw T-27
0017-00101-1746 4 22 Cup 1
23 Pad 1
Tools Required or Assembly
l
Magnetic #2 Bit Phillips Screwdriver
l
5/16” Hex Key Wrench
l
T-27 Torx Key Wrench
3

#8-18 X 3/4”PHILLIPS PAN HEAD
POINTED SCREW (#3)
#8 -18 X 10 PHILLIPS PAN HEAD SCREW (#2)
GROMMET (#20)
FLAT WASHER (#8)
3/8 -16 X 1” HEX SOCKET HEAD CAP SCREW (#1)
CAP SCREW T -27 (#21)
INTERNAL TOOTH LOCK WASHER (#18)
HARDWARE
4

IMPORTANT!
DO NOT DISCARD THE SHIP KIT OCATED ON TOP OF THE PEDA EVERS. A NECESSARY COMPONENTS
NEEDED TO COMP ETE THE INSTA ATION ARE OCATED IN THE SHIP KIT.
IMPORTANTES!
NE JETEZ PAS E KIT P ACÉ SUR E DESSUS DES EVIERS DE PÉDA E. I CONTIENT TOUS ES É ÉMENTS
NÉCESSAIRES POUR 'INSTA ATION.
1. Before proceeding, familiarize yourself with the parts of the
Cross-Trainer and make sure that you have received all the
items described in the Component ist.
2. ocate the left and right FRONT COVER (9 &10). Using two
PHI IPS PAN HEAD POINTED SCREWS (3), mount the EFT FRONT
COVER (9) to the FRAME (A). Attach the RIGHT FRONT COVER (10)
to the FRAME in the same manner using two PHI IPS PANHEAD
POINTED SCREWS (3). Secure the tops of the FRONT COVERS
together using two PHI IPS PANHEAD POINTED SCREWS (3).
CAUTION: Do not overtighten the PHI IPS PAN HEAD POINTED
SCREWS (3).
3. ocate the RIGHT USER ARM (12). Snap the 2-PIN CONNECTOR
(2PA) located at the bottom of the RIGHT USER ARM into the 2-
PIN CONNECTOR (2PB) positioned at the top of the RIGHT ROCKER
ARM (B). Feed the connectors and excess cable up into the
RIGHT USER ARM. Secure the RIGHT USER ARM to the RIGHT
ROCKER ARM using three HEX SOCKET HEAD CAP SCREWS (1) and
three INTERNA TOOTH OCK WASHERS (18). Repeat the procedure
for the EFT USER ARM (11) and EFT ROCKER ARM (C). Tighten
all screws securely.
CAUTION: Be careful not to pinch the WIRE HARNESSES when
assembling the USER ARMS (11 &12) to the ROCKER ARMS (B &
C).
4. Detach and unwrap the WIRE HARNESS (E) (16P, 4P) located at
the top of the MONOCO UMN (F). Holding the CONSO E SUPPORT
ASSEMB Y (7) with the handgrips facing upward, feed the WIRE
HARNESS up through the neck and out the top access hole.
Carefully lower the CONSO E SUPPORT ASSEMB Y into the
MONOCO UMN.
CAUTION: Be careful not to pinch the WIRE HARNESSES (E)
when assembling the CONSO E SUPPORT ASSEMB Y (7) to the
MONOCO UMN (F).
5. Using two HEX SOCKET HEAD CAP SCREWS (1) and two F AT
WASHERS (8), secure the CONSO E SUPPORT ASSEMB Y (7) to the
MONOCO UMN (F). Tighten the SCREWS securely.
6. Insert the GROMMETS (20) into the four holes on the CONSO E
SUPPORT ASSEMB Y. ocate the ACCESSORY TRAY (17). Align the
ACCESSORY TRAY with the four holes on the CONSO E SUPPORT
ASSEMB Y. Using four PHI IPS PAN HEAD POINTED SCREWS (3),
secure the ACCESSORY TRAY to the CONSO E SUPPORT ASSEMB Y
as shown. Tighten the SCREWS securely.
CAUTION: Do not overtighten the PHI IPS PAN HEAD POINTED
SCREWS (3).
7. Remove the adhesive back and install the PAD (23). Install
the CUP (22).
3
10
A
9
3
4P
16P
21 4
3
23
19
2
1
7
F
E
17
20
22
8
11
18
C
B
12
1
2PA
2PB
5

8. Attach the 4-PIN(4P) and 16-PIN(16P) CONNECTORS to the
corresponding JACKS on the back of the CONSO E ASSEMB Y (4).
9. Feed any excess WIRE HARNESS (E) down into the CONSO E
SUPPORT ASSEMB Y (7). Secure the CONSO E ASSEMB Y (4) to the
CONSO E SUPPORT ASSEMB Y using four PHI IPS PANHEAD
SCREWS (2). Tighten the SCREWS securely.
CAUTION: Do not over-tighten the PHI IPS PAN HEAD
SCREWS (2).
CAUTION: Be careful not to pinch the WIRE HARNESS (E) when
assembling the CONSO E ASSEMB Y (4) to the CONSO E SUPPORT
ASSEMB Y (7).
10. ocate and install the CONSO E SUPPORT CAP(19) onto the
CONSO E SUPPORT ASSEMB Y (7) as shown using four CAP
SCREWS (21).
11. Place the BACK MONOCO UMN COVER (6) over the PIVOT SHAFT (H)
at the top of the MONOCO UMN (F).
12. Place the FRONT MONOCO UMN COVER (5) on the opposite side of
the BACK MONOCO UMN COVER (6) to cover the PIVOT SHAFT (G)
and CONSO E SUPPORT ASSEMB Y MOUNTING SCREWS. Interlock the
top tabs and use two PHI IPS PANHEAD POINTED SCREWS (3) to
secure the bottoms of the MONOCO UMN COVERS together.
Tighten the SCREWS securely.
CAUTION: Do not over-tighten the PHI IPS PAN HEAD POINTED
SCREWS (3).
13. ocate one FRONT ROCKER COVER (13) and one BACK ROCKER
COVER (14). Position the FRONT ROCKER COVER over the user
side of the left end of the PIVOT SHAFT (H) (as shown) making
sure that it interlocks with the MONOCO UMN COVERS (5 & 6).
Place the BACK ROCKER COVER over the opposite side of the left
end of the PIVOT SHAFT in the same manner. Secure the COVERS
using three PHI IPS PAN HEAD POINTED SCREWS (3). Repeat the
procedure reversing front and back for the user right end of the
PIVOT SHAFT.
CAUTION: Do not over-tighten the PHI IPS PAN HEAD POINTED
SCREWS (3).
14
13
5
H
F
G
6
314
13
3
4P
16P
21 4
3
23
19
2
1
7
F
E
17
20
22
8
6

PRE-OPERATION CHECKLIST
3 Ensure that all fasteners are tight.
3Make sure the Cross-Trainer is properly leveled and stable.
(Refer to the Cross-Trainer model’s corresponding Operation Manual.)
3Ensure that the eveler Jam Nuts are tight. (Refer to the Cross-Trainer model’s corresponding Operation Manual.)
3Read the entire Operation Manual before using the Cross-Trainer.
LISTE DES VÉRIFICATIONS À EFFECTUER AVANT LA MISE EN MARCHE
3Vérifiez si tous les dispositifs de fixation sont serrés
3Vérifiez si l'APPAREI D'EXERCICE PO YVA ENT est de niveau et stable.(Référez-vous au manuel d'utilisation.)
3Vérifiez si les contre-écrous des vérins de mise à niveau sont serrés.(Référez-vous au manuel d'utilisation.)
3isez le manuel d'utilisation dans son intégralité avant d'utiliser l'appareil d'exercice polyvalent.
Before attempting to operate your Cross-Trainer, it is imperative that you familiarize yourself with the contents of the
Operation Manual. If your Cross-Trainer does not behave as described in the OPERATION MANUA contact ife
Fitness Customer Support Services at 800.735.3867 (toll-free within U.S.A., Canada). Refer to the OPERATION
MANUA for a contact list of International Offices. Prior to your call, please be sure you have located and noted the
MODEL NUMBER & SERIAL NUMBER. The Model & Serial number information of your ife Fitness Cross-Trainer is
listed on a label located on the front stabilizer.
Physical Dimensions
ength: 81 3⁄4in. (207.65 cm.)
Width: 28 in. (71.12 cm.)
Height: 65 in. (165 cm.) with console
Weight (C SX): 239 lbs. (108.41 kg.) 243 lbs. (110.22 kg.) with console
Weight (CSX): 232 lbs. (105.24 kg.) 236 lbs. (107.05 kg.) with console
Shipping Dimensions (without con ole)
ength: 80 in. (203 cm.)
Width: 28 in. (71 cm.)
Height: 47.5 in. (121 cm.)
Weight (C SX): 303 lbs. (137 kg.)
Weight (CSX): 296 lbs. (134.27 kg.)
7