Life Fitness Club Series User manual

CLUB SERIES OLYMPIC INCLINE BENCH
Part # 72xxxx
RevA. Revision:5/02/021
ASSEMBLY INSTRUCTIONS

PARTS LIST
PART #
xx
xx
xx
xx
xx
xx
xx
xx
xx
3102901
KEY
1
2
3
4
5
6
7
8
9
10
QTY
2
1
1
1
1
1
1
2
2
2
KEY
11
12
13
14
15
16
17
OR
18
PART #
3102922
3102905
3102807
3102514
6866701
6866601
6866602
6866603
32024xx
DESCRIPTION
3/8 X 2-3/4” BOLT
3/8 X 3-3/4” BOLT
3/8” LOW HEIGHT LOCK NUT
3/8” SAE WASHER
3/8” RH WASHER
BLACK RH CAP
WHITE RH CAP
PLATINUM RH CAP
3/8 X 4-1/4” BUTTON HD BOLT
QTY
6
18
26
48
52
10
42
42
4
DESCRIPTION
UPRIGHT
SPOTTER SUPPORT
CROSS BRACE
BENCH FRAME
FOOT PLATFORM
BACK PAD
SEAT PAD
BAR SUPPORT RACK
WEIGHT HORN
3/8 X 1-1/4” BOLT
BOLT LENGTH
Tools Required for Assembly
2
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
Bolt Length Ruler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
* Rubber mallet or hammer
* 9/16” wrench
* Ratchet with 9/16” socket
* 3mmAllen wrench

3
12 3/8 X 3-3/4” BOLT
13
3/8” LOW
HEIGHT LOCK
NUT
14
3/8” SAE
WASHER
17
RH CAP
(BLACK/WHITE/PLATINUM)
15
RH
WASHER
11 3/8 X 2-3/4” BOLT
16
18 3/8 X 4-1/4” BUTTON HEAD BOLT
10 3/8 X 1-1/4” BOLT

STEP 1:
FIGURE 1
4
• LOOSELY assemble the two UPRIGHTS (1) to the SPOTTER SUPPORT (2) and the CROSS BRACE (3) using sixteen RH CAPS
(17), eight 3/8 X 3-3/4” BOLTS (12), sixteen 3/8” SAE WASHERS (14), sixteen 3/8” RH WASHERS (15) and eight 3/8” LOW
HEIGHT LOCK NUTS (13) as shown in FIGURE 1.
0123456
1/2 1/2 1/2 1/2 1/2 1/2
15 14
17
1
12
3
3/8 X 3-3/4” 12
2

5
STEP 2:
FIGURE 2
• LOOSELY assemble the BNECH FRAME (4) to the SPOTTER SUPPORT (2) and CROSS BRACE (3) using eight RH CAPS
(17), four 3/8 X 2-3/4” BOLTS (11), eight 3/8” SAE WASHERS (14), eight 3/8” RH WASHERS (15) and four 3/8” LOW HEIGHT
LOCK NUTS (13) as shown in FIGURE 2.
•Securelytightenalllooseframe connectionsmadetothis point, thenproceedtosnapRHCAPS(17)
over the RH WASHERS (15) on all tightened connections.
11 3/8 X 2-3/4”
13
3
15
14
4
17
2

6
STEP 3:
FIGURE 3
0123456
1/2 1/2 1/2 1/2 1/2 1/2
18 3/8 X 4-1/4”
2
5
• SECURELY assemble the FOOT PLATFORM (5) to the SPOTTER SUPPORT (2) using four 3/8 X 4-1/4” BUTTON HEAD
BOLTS (18), four RH CAPS (17). four 3/8” SAE WASHERS (14), four 3/8” RH WASHERS (15) and four 3/8” LOW HEIGHT
LOCK NUTS (13) as shown in FIGURE 3.
14
15
17
13

7
STEP 4:
FIGURE 4
11 3/8 X 2-3/4”
15
6
• SECURELY assemble the BACK PAD (6) to the BENCH FRAME (4) using two RH CAPS (17), two 3/8 X 2-3/4” BOLTS (11)
and two 3/8” RH WASHERS (15) as shown in FIGURE 4.
• SECURELY assemble the SEAT PAD (7) to the BENCH FRAME (4) using two RH CAPS (17), two 3/8 X 1-1/4” BOLTS (10), and
two 3/8” RH WASHERS (15) as shown in FIGURE 4.
17
3/8 X 1-1/4” 10
17
15 4
7

8
STEP 5:
FIGURE 5
13
• SECURELY assemble the two BAR SUPPORT RACKS (8) to the UPRIGHTS (1) using six BLACK RH CAPS (16), six RH CAPS
(17), six 3/8 X 3-3/4” BOLTS (12), twelve 3/8” SAE WASHERS (14), twelve 3/8” RH WASHERS (15) and six 3/8” LOW HEIGHT
LOCK NUTS (13) as shown in FIGURE 5.
1
17
8
15
14
16 12 3/8 X 3-3/4”
0123456
1/2 1/2 1/2 1/2 1/2 1/2

9
STEP 6:
FIGURE 6
• SECURELY assemble the two WEIGHT HORNS (9) to the UPRIGHTS (1) using four BLACK RH CAPS(16), four RH CAPS (17),
four 3/8 X 3-3/4” BOLTS (12), eight 3/8” SAE WASHERS (14), eight 3/8” RH WASHERS (15) and four 3/8” LOW HEIGHT
LOCK NUTS (13) as shown in FIGURE 6.
16
1
17 13
12 3/8 X 3-3/4”
15 14

Clean:
• Upholstery with mild soap and water.
• Guide rods with a cotton cloth.
• Hand grips with mild soap and water.
• Frame damage can be repaired with touch-up paint can be purchased from your LifeFitness customer service representative at
[phone].
Inspect:
• Cables for wear or damage and proper tension (should not exceed 3/4” deflection.) Pay close attention at bends and attachment
points.
• Hardware should be checked for looseness. Tighten as required.
• Frames should be inspected for wear or damage.
• Hand Grips should be checked for wear or damage
Lubricate:
• Lube the Guide Rods. Apply the lubricant to a cotton cloth, then run the cotton cloth up and down the guide rods as needed. Do not
spray lubricant directly on the Guide Rods.
PREVENTATIVE MAINTENANCE TIPS
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
2. Do not allow minors or children to play on or around this equipment.
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
3. Exercise with care to avoid injury.
4. Consult your physician before beginning any exercise program.
10
Thank you for purchasing the LifeFitness CLUB OLYMPIC INLCINE BENCH. If unsure of proper use
of equipment, call your local LifeFitness distributor or call the LifeFitness customer service department
at [phone].
CAUTION-PLEASE READ
Action DAILY WEEKLY QUARTERLY BI-ANNUALLY AS NEEDED
CLEAN
Upholstery X
Guide Rods X
Hand Grips X
INSPECT
Visual Overall X
Cables X
Hardware X
Frame X
Hand Grips X
LUBRICATE
Guide Rods X
WARRANTY INFORMATION
10 YEARS STRUCTURUAL FRAME
3 YEARS PILLOW BLOCKS, PULLEYS, WEIGHT PLATES AND GUIDE RODS
1 YEAR CABLES
90 DAYS UPHOLSTERY