Life Fitness CLUB TRICEP Series User manual

CLUB SERIES TRICEP
Part # 7167101
Rev D Revision:10/12/011
ASSEMBLY INSTRUCTIONS

PARTS LIST
KEY PART
#
DESCRIPTION QT
Y
KEY PART
#
DESCRIPTION QT
Y
1 69928xx TOWER 1 17 3202404 3/8 X 3” BUTTON HEAD BOLT 4
1A 6988801 CABLE 1 18 3108406 3/8 X 3/4” FLAT HEAD BOLT 2
1B 6714901 GUIDE ROD BUSHING 2 19 3102807 3/8” LOW HEIGHT LOCK NUT 21
1C 6925801 LABEL, KEEP CLEAR 1 20 3221501 3/8” ACORN NUT 1
1D 6692601 3 X 2 END CAP 3 21 3102514 3/8” SAE WASHER 26
1E 3102903 3/8-16 X 2.5 BOLT 2 22 3114502 3/8” LOCK WASHER 1
1F 3102933 3/8-16 X 2 BOLT 1 23 6886701 3/8” RH WASHER 46
1G 6480301 3/8 SPACER 4 24 3233502 1/2 X 3-1/4” SHOULDER BOLT 1
1H 3102514 3/8 FLAT WASHER 2 25 6020601 1/2” FLANGE BEARING 2
1I 6866701 3/8 RH WASHER 4 26 3203501 PILLOW BLOCK 2
1J 3102807 3/8-16 NYLOCK NUT LOW HT 3 27 6913801 WEIGHT STACK SELECTOR PIN 1
1K 6866601 CAP, RH-20 BLK 4 28 3108001 WEIGHT STACK CUSHION 2
1L 3222801 4.5" PULLEY 3 29 6866601 BLACK RH CAP 6
2 69911xx ASSY, ARM SUPPORT 1 30 3222001 1” SHAFT COLLAR 2
3 69901xx ASSY, HANDLE 1 31 3116001 1-1/4” RUBBER BUMPER 3
3A 6994501 RUBBER GRIP 2 32 6714901 GUIDE ROD BUSHING 2
3B 6989801 RUBBER STOP 2 33 6912801 ACCORDION SLEEVE 2
4 69897xx ASSY, PIVOT ARM 1 34 6984101 PLACARD LABEL 1
5 68839xx GUIDE ROD SUPPORT 1 35 6986301 LANGUAGE PLACARD LABEL 1
6 6888902 CAM SHROUD 1 36 6925502 HEAD PLATE 1
7 6890902 COUNTERBALANCE 1 37 6926901 GUIDE ROD 2
8 68856xx CROSS SUPPORT 1 38 6887202 10 LB. WEIGHT PLATE (STD) 15
9 71669xx SEAT SUPPORT 1 39 6888402 15 LB. WEIGHT PLATE (OPT) 10
9A 6990602 ASSY, SEAT ADJUST BLK 1 40 69132xx ARM/CHEST PAD 4
9B 6797101 ADJ PLATE 1 41 69131xx SEAT PAD 1
9C 6897001 ADJ PLATE 15 POS 1 42 6971601 WEIGHT STACK LABEL 1
9D 3234301 SCREW 4 43 3230701 STARLOCK WASHER 4
9E 6912202 HINGE 1 44 6866602 WHITE RH CAP 40
9F 6896901 HINGE PIN 2 OR 6866603 PLATINUM RH CAP 40
9G 3102416 END CAP, 2 X 1 3 45 6861902 TOP COVER SHROUD BLK 1
9H 3221701 E-RING EXTERNAL 3/8 4 46 6862102 FRONT SIDE SHROUD BLK 2
10 68888xx 4 X 18” PLATE 1 47 6862007 FRONT PLATINUM SHROUD 1
11 3102901 3/8 X 1-1/4” BOLT 8 48 6925302 ASSY, REAR FULL SHROUD 1
12 3102924 3/8 X 1-3/4” BOLT 2 OPTION* 6921502 ASSY, FRONT FULL SHROUD 1
13 3102903 3/8 X 2-1/2” BOLT 3
14 3102922 3/8 X 2-3/4” BOLT 6
15 3102942 3/8 X 3-1/2” BOLT 2
16 3102905 3/8 X 3-3/4” BOLT 4
*For all 5 digit part numbers you need to add the color at the end. **Language placard kit comes with Dutch, French,
For shrouds and weldments please use the following codes: German, Poruguese, Spanish, Japaneese, and
xxxxx07 Denotes Platinum Italian.
xxxxx08 Denotes White
*For upholstery, please use the following codes:
#02ROYAL BLUE
#03SLATE
#04CRANBERRY
#05NORTHWOODS
#06 SPACE BLUE
#07AMERICAN BEAUTY RED
#08SUEDE
#12 BLACK
#13HUNTER GREEN
#14 REGIMENTAL BLUE
#15GINGERSNAP
#16CONCORD
#17URQUOISE
#18 RASPBERRY
#19CROCUS

2"
4X
3X
4X
2X
4X
3X
2X
1
1B
1D
1C
1E
1E
1F
1I
1H
1J
1K
1G
SECTION A-A
3X
1A
1L

STEP 1:
FIGURE 1
4
0123456
1/2 1/2 1/2 1/2 1/2 1/2
3/8 X 2-3/4” 14
44
21 23
1
19
2
• LOOSELY assemble the top of the ARM SUPPORT (2) to the TOWER (1) using four RH CAPS (44), two 3/8 X 2-3/4” BOLTS
(14), four 3/8” SAE WASHERS (21), four 3/8” RH WASHERS (23) and two 3/8” LOW HEIGHT LOCK NUTS (19) as shown in
FIGURE 1.
• LOOSELY assemble the bottom of theARM SUPPORT (2) to the TOWER (1) using four RH CAPS (44), two 3/8 X 3-3/4” BOLTS
(16), four 3/8” SAE WASHERS (21), four 3/8” RH WASHERS (23) and two 3/8” LOW HEIGHT LOCK NUTS (19) as shown in
FIGURE 1.
3/8 X 3-3/4” 16
1A

• LOOSELY assemble the SEAT FRAME (9) to the ARM SUPPORT (2) using four RH CAPS (44), two 3/8 X 3-3/4” BOLTS (16),
four 3/8” SAE WASHERS (21), four 3/8” RH WASHERS (23), and two 3/8” LOW HEIGHT LOCK NUTS (19) as shown in
FIGURE 2.
STEP 2:
FIGURE 2
5
3/8 X 3-3/4” 16
9
19
2
23
21
44
9F 9H 9E
1A
9C
9G
9D 9B
9A

6
0123456
1/2 1/2 1/2 1/2 1/2 1/2
STEP 3:
FIGURE 3
•Securely tighten all loose frame connections made to this point, then proceed to snap RH
CAPS (44) over the RH WASHERS (23) on all tightened connections.
• LOOSELY assemble the CROSS SUPPORT (8) to theARM SUPPORT (2) and SEAT FRAME (9) using eight RH CAPS (44), four
3/8 X 2-3/4 BOLTS (14), eight 3/8” SAE WASHERS (21), eight 3/8” RH WASHERS (23) and four 3/8” LOW HEIGHT LOCK
NUTS (19) as shown in FIGURE 3.
3/8 X 2-3/4” 14
9
8
2
23
21
44
19
1A

7
• Slide two ACCORDION SLEEVES (33) and two PILLOW BLOCKS (26) over the PIVOT ARM (4) as shown in FIGURE 4
STEP 4
FIGURE 4
• SECURELY assemble the PIVOT ARM (4) to the ARM SUPPORT (2) using four previously inserted 3/8 X 3” BUTTON HEAD
CAP SCREWS (17), four RH WASHERS (23), four 3/8” SAE WASHERS (21), four 3/8” LOW HEIGHT LOCK NUTS (19) and
four RH CAPS (44) as shown in FIGURE 5.
STEP 5:
FIGURE 5
33
26
4
• Attach two 1-1/4” RUBBER BUMPER (31) to the ARM SUPPORT (2) where the PIVOT ARM (4) shaft contacts tube in both
directions.
TIGHTEN!
SET SCREWS
3/8 X 3” 17
2
19
44
23
4
31
• IMPORTANT! When PIVOT ARM (4) is centered and level in the PILLOW BLOCKS (26), tighten the PILLOW BLOCK set
screws.
31
21
43
17 3/8 X 3”
BUTTON HEAD
• Assemble four 3/8 X 3” BUTTON HEAD CAP SCREWS (17) and four STARLOCK WASHERS (43) to the the PILLOW
BLOCKS (26) as shown in FIGURE 4.

8
STEP 6:
FIGURE 6
• SECURELY assemble the COUNTERBALANCE (7) to the PIVOT ARM (4) using two RH CAPS (44), one 3/8 X 2-1/2” BOLT
(13), two 3/8” SAE WASHERS (21), two 3/8” RH WASHERS (23) and one 3/8” LOW HEIGHT LOCK NUT (19) as shown in
FIGURE 6.
STEP 7:
FIGURE 7
• Rotate the PIVOTARM (4) up to it’s resting position and slide the end of the CABLE into the bushing on the PIVOT ARM (4) as
shown in FIGURE 7.
13 3/8 X 2-1/2”
23
44
21
7
4
19
4
CABLE
2
0123456
1/2 1/2 1/2 1/2 1/2 1/2

9
STEP 8:
FIGURE 8
STEP 9:
FIGURE 9
• Assemble the HANDLE (3) to the PIVOT ARM (4) using one 1/2 X 3-1/4” SHOULDER BOLT (24), one 3/8” LOCK WASHER
(22), and one 3/8” ACORN NUT (20) as shown in FIGURE 9. (NOTE: Tighten enough to allow HANDLE to rotate freely.)
• Insert two 1/2” FLANGE BEARINGS (25) into the HANDLE (3) as shown in FIGURE 8.
25
3
24 1/2 X 3-1/4”
22
20
4
3
31
• Attach one 1-1/4” RUBBER BUMPER (31) to the HANDLE (3) as shown in FIGURE 8
3B
3A

STEP 11:
FIGURE 11
• SECURELYassemble the SEAT PAD (41) to the seat adjust on the SEATADJUST (9A) using two BLACK RH CAPS (29), two 3/8 X
1-3/4”BOLTS (12)and two 3/8”RHWASHERS (23)as shown inFIGURE 10.
12 3/8 X 1-3/4”
29
9 23
41
0123456
1/2 1/2 1/2 1/2 1/2 1/2
10
STEP 10:
FIGURE 10
• SECURELY assemble the CAM SHROUD (6) to the ARM SUPPORT (2) using two RH CAPS (44), two BLACK RH CAPS
(29), two 3/8 X 3-1/2” BOLTS (15), four 3/8” RH WASHERS (23) and two 3/8” LOW HEIGHT LOCK NUTS (19) as shown
in FIGURE 10.
3/8 X 3-1/2” 15
19
6
23
44
2
29
1A
9A