Life Fitness Club Series User manual

CLUB SERIES ADJUSTABLE AB BENCH
Part # 7320301
RevC. Revision:11/18/021
ASSEMBLY INSTRUCTIONS
End of Life

PARTS LIST
PART #
AP04-0013
P04-0011
AP04-0014
AP04-0012
AP01-0032
P07-0005
P07-0002
AP04-0023
DA1C03817016NU
DA1C03806816NU
DA1C03808316NU
DA1C03816416NU
KEY
1
2
3
4
5
6
7
8
9
10
11
12
QTY
1
1
2
1
2
1
1
1
2
4
4
1
KEY
13
14
15
16
OR
17
18
19
20
21
22
PART #
DB2E03807200NU
DC120010510U
P05-0009
P06-0021
P06-0021
P06-0012
P06-0005
P06-0013
P06-0007
P06-0006
P03-0004
DESCRIPTION
3/8”LOWHEIGHTLOCKNUT
3/8”SAEWASHER
3/8”RHWASHER
WHITERH CAP
PLATINUMRHCAP
1-1/4”SHAFTCOLLAR
5X8”ROLLERPAD
2-3/8”OD PLASTICWASHER
2”SQ.ENDCAP
3X2”ENDCAP
3/4 X 5-5/16” CHROME PIVOT SHAFT
QTY
7
18
18
18
18
4
4
8
1
1
1
DESCRIPTION
SEAT
FRAME
PAD ADJUST
BASE
19-1/4” ROLLER PAD TUBE
SEATPAD
BENCHPAD
REARBASE
3/8X170mmBOLT
3/8X68mmBOLT
3/8X83mmBOLT
3/8X164mmBOLT
BOLT LENGTH
Tools Required forAssembly
2
NOTE:BOLTLENGTHISMEASUREDFROMTHE UNDERSIDE OFTHE HEAD OFTHE BOLT.
Bolt Length Ruler
* 9/16” wrench
* Ratchet with 9/16” socket
* 3mmAllen wrench (Supplied)
* 4mmAllen wrench (Supplied)
01
1/2 1/2 1/2 1/2 1/2 1/2
23456
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

3
11 3/8X 83mm BOLT
12 3/8X164mmBOLT
9 3/8 X 170mm BOLT
13
3/8” LOW
HEIGHT LOCK
NUT
14
3/8” SAE
WASHER
RH CAP
(WHITE/PLATINUM)
15
RH
WASHER
10 3/8X 68mmBOLT
16

STEP 1:
FIGURE 1
4
• SECURELYassemble the BASE (4)to the FRAME(2) using fourRH CAPS (16),two 3/8 X68mm BOLTS(10), four 3/8” SAE
WASHERS(14), four 3/8” RHWASHERS(15) and two 3/8” LOWHEIGHTLOCKNUTS (13) as shown inFIGURE 1.
10 3/8X68mm
4
2
13
14
15
16
10 3/8X68mm
8
• SECURELY assemble the REAR BASE (8) to the FRAME (2) using four RH CAPS (16), two 3/8 X 68mm BOLTS (10), four 3/8” SAE
WASHERS(14), four 3/8” RHWASHERS(15) and two 3/8” LOWHEIGHTLOCKNUTS (13) as shown inFIGURE 1.

5
STEP 2:
FIGURE 2
• SECURELYassemble the SEAT (1) to the FRAME (2) using two RH CAPS (16), one 3/8 X 164mm BOLT (12), two 3/8” SAEWASH-
ERS(14), two 3/8” RHWASHERS(15) and one 3/8”LOWHEIGHTLOCKNUT(13) as shownin FIGURE 2.
12 3/8X164mm
13
16
2
1514
1

6
STEP 3:
FIGURE 3
• SECURELYassemble two PADADJUSTS (3) to the SEAT (1) using two RH CAPS (16), one 3/8 X 170mm BOLT (9), two 3/8” SAE
WASHERS(14), two 3/8” RH WASHERS (15) andone 3/8” LOWHEIGHTLOCK NUT(13) as shown in FIGURE3.
• SECURELY assemble one 3/4” X 5-5/16” CHROME PIVOT SHAFT (22) between the two PAD ADJUSTS (3) using two RH
CAPS(16), one 3/8 X170mm BOLT (9), two 3/8” SAEWASHERS (14), two 3/8” RHWASHERS (15)and one 3/8” LOWHEIGHT
LOCKNUT(13)as shown in FIGURE 3.
22 CHROME
3/8X 170mm 9
1
13
3
16
15
14

STEP 4:
FIGURE 4
7
16
7
1
6
3/8X83mm 11
15
• SECURELY assemble the BACK PAD (7) to the SEAT (1) usingtwo RH CAPS (16), two 3/8 X 83mm BOLTS (11), two 3/8” SAE
WASHERS(14) and two 3/8” RHWASHERS (15) as shown in FIGURE 4.
• SECURELYassemble the SEATPAD (6) to the SEAT(1)using two RH CAPS (16), two 3/8 X 83mm BOLTS (11),two 3/8” SAE
WASHERS(14) and two 3/8” RHWASHERS (15) as shown in FIGURE 4.
14

8
STEP 5:
FIGURE 5
• Assemble four 5 X 8” ROLLER PADS (18) to the SEAT (1) using four 1-1/4” SHAFT COLLARS (17), eight 2-3/8” OD PLASTIC
WASHERS (19) and two 19-1/4” ROLLER PAD TUBES (5) as shown in FIGURE 5. Once the ROLLER PADS (18) are assembled
to the SEAT (1), SECURE the 19-1/4” ROLLER PAD TUBES (5) in place using the four SET SCREWS in the tubes on the SEAT
(1) as shown in FIGURE 5..
17
1
5
18
• Insert one 3 X 2” END CAPS (21) and one 2” SQ. END CAP (20) into the BASE (1) as shown in FIGURE 5.
21
20
SERIAL#
LOCATION
SET SCREWS
SET SCREWS 19

Clean:
• Upholstery with mild soap and water.
• Guide rods with a cotton cloth.
• Hand grips with mild soap and water.
• Frame damage can be repaired with touch-up paint can be purchased from your LifeFitness customer service representative at
[phone].
Inspect:
• Cables for wear or damage and proper tension (should not exceed 3/4” deflection.) Pay close attention at bends and attachment
points.
• Hardware should be checked for looseness. Tighten as required.
• Frames should be inspected for wear or damage.
• Hand Grips should be checked for wear or damage
Lubricate:
• Lube the Guide Rods. Apply the lubricant to a cotton cloth, then run the cotton cloth up and down the guide rods as needed. Do not
spray lubricant directly on the Guide Rods.
PREVENTATIVE MAINTENANCETIPS
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
2. Do not allow minors or children to play on or around this equipment.
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
3. Exercise with care to avoid injury.
4. Consult your physician before beginning any exercise program.
9
Thank you for purchasing the LifeFitness CLUB SERIESADJUSTABLEAB BENCH. If unsure of
proper use of equipment, call your local LifeFitness distributor or call the LifeFitness customer service
department at [phone].
CAUTION-PLEASE READ
Action DAILY WEEKLY QUARTERLY BI-ANNUALLY AS NEEDED
CLEAN
Upholstery X
Guide Rods X
Hand Grips X
INSPECT
Visual Overall X
Cables X
Hardware X
Frame X
Hand Grips X
LUBRICATE
Guide Rods X
WARRANTYINFORMATION
10YEARS STRUCTURUALFRAME
3YEARS PILLOWBLOCKS, PULLEYS,WEIGHT PLATESANDGUIDE RODS
1YEAR CABLES
90 DAYS UPHOLSTERY