Life Gear Transport EMS User manual

TRANSPORT EMS
MAGNETIC UPRIGHT BIKE
ITEM NO.: 20695
OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without notice.

1
TABLE OF CONTENTS
WARRANTY ------------------------------------------------------------------------------- 2
IMPORTANT SAFETY INSTRUCTIONS ------------------------------------------- 3
PARTS LIST ------------------------------------------------------------------------------- 4
HARDWARE PACKING LIST --------------------------------------------------------- 6
TOOLS -------------------------------------------------------------------------------------- 6
OVERVIEW DRAWING ----------------------------------------------------------------- 7
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 8
OPERATING THE COMPUTER ------------------------------------------------------ 13
ADJUSTMENTS -------------------------------------------------------------------------- 19
MAINTENANCE -------------------------------------------------------------------------- 20
TROUBLESHOOTING ------------------------------------------------------------------ 20
WARM UP AND COOL DOWN ROUTINE ----------------------------------------- 21

2
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it
has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's
obligation under this warranty is limited to replacing or repairing free of charge, any parts
which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is offered only to the original owner and is not transferable. Proof of
purchase is required.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

3
IMPORTANT SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following important
safety instructions when using this equipment. Read all instructions before using
this equipment.
1. Read all instructions and follow it carefully before using this equipment. Make sure the
equipment is properly assembled and tightened before use.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercises are
recommended.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that may catch any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult your local dealer.
6. Do not use the equipment outdoors.
7. This equipment is for household use only. It is not a commercial model.
8. Only one person at a time should use this equipment.
9. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
10. Care should be taken in mounting or dismounting the equipment.
11. Do not allow children to use or play on the equipment. Keep children and pets away
from the equipment while in use. This machine is designed for adults use only. The
minimum free space required for safe operation is not less than two meters.
12. The maximum weight capacity for this product is 110 kgs.
WARNING:Before beginning any exercise program consult your physician.
This is especially important for the people who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness
equipment.
CAUTION:Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

4
PARTS LIST
No. Description Qty No. Description Qty
001 Computer (TZ-6185E) 1 023 Seat Cushion DD-353T 1
002 Clamp Cover 1 024 Seat Sliding Tube End Cap
38x38 2
003 Handlebar End Cap Ø25 2 025 Nylon Nut M8 3
004 Handlebar Ø25 1 026 Washer Ø8xØ20x2.0t 3
005 Handlebar Foam Grip
Ø24xØ30x490 2 027 Seat Sliding Tube 1
006 Hand Pulse Sensor with Wire
L=750mm 2 028 Seat Sliding Tube Bolt 1
007 Cross Recessed Pan Head Self
Tapping Screw ST4.2x20mm 2 029 Washer Ø10xØ25x2.0t 1
008 Wire Grommet Ø12.1 1 030 Seat Adjustment Knob M10 1
009 Handlebar T-Knob M8x55 1 031 Seat Post 1
010 Spacer Ø12x1.5x20 1 032 Seat Post Cover 1
011 Cross Recessed Pan Head Bolt
M5x12mm 4 033 Seat Height Adjustment Knob M16x1.5 1
012
Cross Recessed Pan Head Self
Drilling Tapping Screw
ST4.2x20mm
6 034 Seat Post Bushing 1
013 Hexagon Nut M12x3t 1 035 Connector 1
014 Handlebar Post Ø76 1 036 Thermal Insulator Pad 1
015 Computer Extension Wire II
(1150mm) 1 037 Hexagon Socket Pan Head Cap Bolt M6x20 4
016 Magnetic System 1 038 Washer Ø6xØ16x1.2t 4
017 Power Supply Wire 1 039 Transport Wheel Ø45x19 2
018 AC Adapter 1 040 Cross Recessed Pan Head Bolt
M6x40 2
019 Curve Washer Ø8 6 041 Nylon Nut M6 10
020 Hexagon Socket Pan Head Cap
Bolt M8x15 6 042 Front Left Stabilizer End Cap 1
021 Handlebar Post Cover 1 043 Front Stabilizer Ø76x1.5tx430 1
022L Left Seat Sliding Tube Cover 1 044 Carriage Bolt M8x90mm 2
022R Right Seat Sliding Tube Cover 1 045 Curve Washer Ø8xØ20x2.0t 4

5
PARTS LIST
No. Description Qty No. Description Qty
046 Cap Nut M8 2 063 Bearing 6003-2Z 2
047 Front Right Stabilizer End Cap 1 064 Sensor with Wire L=200mm 1
048 Main Frame 1 065 Belt Pulley 260J6 1
049L Left Foot Pedal 1 066 Belt PJ370 J6 1
049R Right Foot Pedal 1 067 Belt Pulley Shaft 1
050 Crank Cover 2 068 Cross Recessed Pan Head Bolt
M6x15mm 4
051 Nut M10x1.25x10 2 069 Cross Recessed Pan Head Self
Tapping Screw ST4.2x25 8
052L Left Crank 1 070 Hexagon Socket Pan Head Cap
Bolt M8x45 1
052R Right Crank 1 071 Idler Arm 1
053 Cover Cap Ø40xØ25x10 2 072 Washer Ø10xØ14x1.0t 2
054L Left Shroud 1 073 Rear Stabilizer End Cap Ø76 2
054R Right Shroud 1 074 Rear Stabilizer Ø76x1.5tx480 1
055
Cross Recessed Pan Head Self
Drilling Tapping Screw
ST4.2x25mm
4 075 Hexagon Nut M10 2
056 Hexagon Socket Pan Head Cap
Bolt M8x10 1 076 Adjustable Leveler M10 2
057 Plastic Pad Ø10xØ20x2.0 6 077 Hexagon Socket Pan Head Cap
Bolt M8x90mm 2
058 Hexagon Socket Pan Head Cap
Bolt M5x15 2 078 Cross Recessed Pan Head Self Tapping Screw ST2.9x16mm 5
059 Washer Ø6 5 079 Computer Extension Wire I
(650mm) 1
060 Cross Recessed Pan Head Bolt
M6x10mm 1 080 Cross Recessed Pan Head Self Tapping Screw ST2.9x12 2
061 Bearing 6000-2Z 2 081 Spring Washer Ø6 4
062 Spring Clip Ø17x1.0t 2 082 Nylon Nut M5 2

6
HARDWARE PACKING LIST
TOOLS
(12) Cross Recessed Pan
Head Self Drilling Tapping
Screw ST4.2x20mm
2 PCS
(78) Cross Recessed Pan
Head Self Tapping Screw
ST2.9x16mm
5 PCS
(44) Carriage Bolt M8x90mm
2 PCS
(45) Curve Washer
Ø8xØ20x2.0t
4 PCS
(46) Cap Nut M8
2 PCS
(77) Hexagon Socket Pan
Head Cap Bolt M8x90mm
2 PCS
Allen Wrench S6
1 PC
Multi Hex Tool with Phillips Screwdriver
S10, S13, S14, S15
1 PC
Multi Hex Tool
S10, S13, S17, S19
1 PC

7
OVERVIEW DRAWING
23
22L
39
42
47
24
28
25
26
22R
12
29
31
24
30
32
33
34
41 40
46
45
44
66
69 49R
52R
50
51
53
54R
68
67
41
64
65
63
54L
53
52L
51
50
55
49L
80
48
43
79
1
210 9
5
4
5
7
67
6
8
11
14
19 20
15
21
3
3
18
17
35 36
39
41 40
12
62
59
69
69
69
73
74
73
45
77
75
76
78
60 59 61 72 61
70
56
71
13
62
78
63
55
27
12
37
38
16
41
58
82
57
81

8
ASSEMBLY INSTRUCTIONS
1. Front/Rear Stabilizers and Right/Left Foot Pedals Installation
Position the Front Stabilizer (43) in front of Main Frame (48) and align bolt holes.
Attach the Front Stabilizer (43) onto the front curve of the Main Frame (48) with two
M8x90mm Carriage Bolts (44), two Ø8xØ20x2.0t Curve Washers (45), and two M8 Cap
Nuts (46). Tighten cap nuts with the Multi hex Tool with Phillips Screwdriver provided.
Position the Rear Stabilizer (74) behind the Main Frame (48) and align bolt holes.
Attach the Rear Stabilizer (74) onto the rear curve of the Main Frame (48) with two
M8x90mm Hexagon Socket Pan Head Cap Bolt (77) and two Ø8xØ20x2.0t Curve Washers
(45). Tighten bolts with the S6 Allen Wrench provided.
Install two M10 Adjustable Levelers (76) with two M10 Hexagon Nuts (75) onto the Rear
Stabilizer (74).
Foot Pedals Installation
The Cranks, Foot Pedals, Pedal Shafts and Pedal Straps are marked “R” for Right and
“L” for Left.
Insert the pedal shaft of Left Foot Pedal (49L) into threaded hole in the Left Crank (52L).
Turn the pedal shaft by hand in the counter-clockwise direction until snug.
Note: DO NOT turn the pedal shaft in the clockwise direction, doing so will strip the
threads.
Tighten the pedal shaft of Left Foot Pedal (49L) with the Multi Hex Tool with Phillips
Screwdriver provided.
Insert pedal shaft of Right Foot Pedal (49R) into threaded hole in Right Crank (52R). Turn
the pedal shaft by hand in the clockwise direction until snug.
Tighten pedal shaft of Right Foot Pedal (49R) with the Multi Hex Tool with Phillips
Screwdriver provided.
Multi Hex Tool with Phillips Screwdriver
S10, S13, S14, S15
Tool:
Allen Wrench S6
46
45
49R
74
76
45
49L
77
48
44
43
52L
75
52R

9
Hardware:
․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․
2. Seat Post, Seat Cushion, Seat Sliding Tube, and Seat Sliding Tube Covers
Installation
Slide the Seat Post Cover (32) onto the tube of the Main Frame (48). Insert the Seat Post
(31) into the Seat Post Bushing (34) on the tube of the Main Frame (48) and then attach the
Seat Height Adjustment Knob (33) onto the tube of the Main Frame (48) by turning it in a
clockwise direction with Multi Hex Tool provided to lock the Seat Post (31) in the suitable
position.
Remove three M8 Nylon Nuts (25) and three Ø8xØ20x2.0t Washers (26) from underside of
the Seat Cushion (23). Remove nylon nuts with the Multi Hex Tool with Phillips
Screwdriver provided. Guide bolts on underside of the Seat Cushion (23) through holes on
top of the Seat Sliding Tube (27), attach with three removed M8 Nylon Nuts (25) and
Ø8xØ20x2.0t Washers (26). Tighten nylon nuts and washers with the Multi Hex Tool with
Phillips Screwdriver provided. Remove the Ø10xØ25x2.0t Big Washer (29) and Seat
Adjustment Knob (30) from the Seat Sliding Tube Bolt (28). Guide the Seat Sliding Tube
Bolt (28) on underside of the Seat Sliding Tube (27) through hole on top of the Seat Post
(31), attach with the Ø10xØ25x2.0t Big Washer (29) and Seat Adjustment Knob (30) that
were removed.
Attach the Left and Right Seat Sliding Tube Covers (22L, 22R) onto the Seat Sliding Tube
(27) and Seat Post (31) with two ST4.2x20mm Cross Recessed Pan Head Self Drilling
Tapping Screws (12) and five ST2.9x16mm Cross Recessed Pan Head Self Tapping
Screws (78). Tighten screws with the Multi Hex Tool with Phillips Screwdriver provided.
(44) Carriage Bolt
M8x90mm
2 PCS
(45) Curve Washer
Ø8xØ20x2.0t
4 PCS
(46) Cap Nut M8
2 PCS
(77) Hexagon Socket Pan
Head Cap Bolt M8x90mm
2 PCS
Multi Hex Tool
S10, S13, S17, S19
Multi Hex Tool with Phillips Screwdriver
S10, S13, S14, S15
Tool:
22L
12
22R
12 78
27 25
26
29
31
23
30
33
32
34
48
28