Life Gear 20582 User manual

FORMULA
MAGNETIC UPRIGHT BIKE
ITEM NO.: 20582
OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo and are subject to change without
prior notice. 2020, Sept.

1
TABLE OF CONTENTS
WARRANTY ------------------------------------------------------------------------------- 2
IMPORTANT SAFETY INSTRUCTIONS ------------------------------------------- 3
PARTS LIST ------------------------------------------------------------------------------- 4
HARDWARE LIST ----------------------------------------------------------------------- 6
TOOLS -------------------------------------------------------------------------------------- 6
EXPLODED VIEW ----------------------------------------------------------------------- 7
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 8
HOW TO MOVE THE UPRIGHT BIKE --------------------------------------------- 20
OPERATING THE COMPUTER ------------------------------------------------------ 21
ADJUSTMENTS -------------------------------------------------------------------------- 22
MAINTENANCE -------------------------------------------------------------------------- 23
TROUBLESHOOTING ----------------------------------------------------------------- 23
WARM UP AND COOL DOWN ROUTINE ---------------------------------------- 24

2
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it
has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's
obligation under this warranty is limited to replacing or repairing free of charge, any parts
which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is offered only to the original owner and is not transferable. Proof of
purchase is required.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

3
IMPORTANT SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following important
safety instructions when using this equipment. Read all instructions before using
this equipment.
1. Read all instructions and follow it carefully before using this equipment. Make sure the
equipment is properly assembled and tightened before use.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercises are
recommended.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that may catch any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult your local dealer.
6. Do not use the equipment outdoors.
7. This equipment is for household use only. It is not a commercial model.
8. Only one person at a time should use this equipment.
9. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
10. Care should be taken in mounting or dismounting the equipment.
11. Do not allow children to use or play on the equipment. Keep children and pets away
from the equipment while in use. This machine is designed for adults use only. The
minimum free space required for safe operation is not less than two meters.
12. The maximum weight capacity for this product is 110 kg.
WARNING: Before beginning any exercise program consult your
physician. This is especially important for people who are over 35 years old or who
have pre-existing health problems. Read all instructions before using any fitness
equipment. Do not operate this exercise equipment without properly fitted guards,
as the moving parts can present a risk of serious injury if exposed.
CAUTION: Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

4
PARTS LIST
No. Description Qty No. Description Qty
001 Main Frame 1 027 Nut M10x1x6 2
002 Handlebar Post 1 028 Flywheel Ø230x40xØ32 1
003 Seat Post 1 029 Rear Left Stabilizer End Cap 1
004 Seat Sliding Tube 1 030 Hexagon Nut M10 2
005 Adjustable Handlebar
Ø25x1.5x1280 1 031 Carriage Bolt M8x70 4
006 Front Stabilizer Ø60x1.5x330 1 032 Adjustable Leveler M10 2
007 Rear Stabilizer Ø60x1.5x480 1 033 Big Curve Washer Ø8 4
008 Left Cover 640x399x84 1 034 Cap Nut M8 4
009 Right Cover 640x399x81 1 035 Front Left Stabilizer End Cap
Ø60x1.5 1
010 Left Foot Pedal YH-30X 1 036 Nylon Nut M8 5
011 Right Foot Pedal YH-30X 1 037 Washer Ø16xØ8x1.5 9
012 Cover Cap Ø40xØ25x10 2 038 Bearing 6000Z 2
013 Belt PJ 360J6 1 039 Idle Wheel Bracket 1
014 Belt Pulley with Crank Ø240J6 1 040 Hexagon Socket Pan Head Cap
Bolt M8x18 1
015 Washer Ø23xØ34.5x2.5 1 041 Spring Ø17x80xØ2.5 1
016 Bearing Nut II 7/8" 1 042 Seat Post Knob M16x1.5 1
017 Bearing 2 043 Seat Post Bushing 1
018 Bearing Cup 2 044 Seat Post Cover 1
019 Bearing Nut I 15/16" 1 045 Seat Adjustment Knob M10 1
020 Hexagon Nut 7/8" 1 046 Seat Sliding Tube Bolt 1
021 Cross Recessed Pan Head
Tapping Screw ST4.2x25 6 047 Seat Sliding Tube End Cap (□38) 2
022
Cross Recessed Pan Head Drilling
Screw with Tapping Screw Thread
ST4.2x25
4 048 Seat Cushion DD-982AT 1
023 Hexagon Nut M6 2 049 Computer 1
024 Tension Bracket 2 050 Tension Control Knob 1
025 Spring Washer Ø6 2 051 Cross Recessed Pan Head Bolt
M5x10 4
026 Eyebolt M6x36 2 052 Hexagon Socket Pan Head Cap
Bolt M8x10 4

5
PARTS LIST
No. Description Qty No. Description Qty
053 Hexagon Socket Pan Head Cap
Bolt M8x15 1 064 Spacer (Ø12x20x1.5) 1
054 Curve Washer Ø16xØ8x1.5 1 065 Clamp Cover 1
055 Handlebar Post Cover 1 066 Extension Sensor Wire
(L=1100 mm) 1
056 Sensor with Wire L=750 mm 1 067 Tension Cable (L=1350 mm) 1
057 Cross Recessed Pan Head
Tapping Screw ST2.9x12 1 068 Front Right Stabilizer End Cap 1
058 Handlebar Foam Grip
Ø24xØ30x520 2 069 Washer Ø10xØ20x2 1
059 Handlebar End Cap Ø25 2 070 Washer Ø24xØ40x3 1
060 Rear Right Stabilizer End Cap 1 071 Cross Recessed Pan Head
Tapping Bolt M5x15 1
061 Hand Pulse Sensor with Wire
L=750 mm 2 072 Big Washer Ø5 1
062 Cross Recessed Pan Head
Tapping Screw ST4.2x20 4 073 Wire Grommet Ø12.1 1
063 Handlebar T-Knob (M8x55) 1

6
HARDWARE LIST
TOOLS
(31) Carriage Bolt
4 PCS
(34) Cap Nut
4 PCS
(33) Big Curve Washer
4 PCS
Allen Wrench
1 PC
Multi Hex Tool with Phillips Screwdriver
1 PC
Multi Hex Tool
1 PC

7
EXPLODED VIEW
22
11
12
22
9
13
14
32
31
30
60
30
42
18
17 16 70
41
39
38
40
7
33
34
36 37
28
27 26
23 24
25
20
19 17
15
18
29
22
21
8
10
12
21
43
44
55
3
69
45
47
48
37 36
4
46
47
67
2
71 72
49
68
51
50
5
58
58
59
59
63
64 65
61
62
62
61
1
35
6
33
34
62
31
62
57
56
32
52
37
66
52 37
53 54
73
67
66
26
22

8
ASSEMBLY INSTRUCTIONS
STEP 1
Position the Front Stabilizer (6) in front of the Main Frame (1) and align bolt holes.
Attach the Front Stabilizer (6) onto the front curve plate of the Main Frame (1) with two
Carriage Bolts (31), two Big Curve Washers (33), and two Cap Nuts (34). Tighten cap nuts
with the Multi Hex Tool with Phillips Screwdriver provided.
Hardware:
33
34
31
1
6
33 34
31
33
34
31
16
(31) Carriage Bolt
2 PCS
(34) Cap Nut
2 PCS
(33) Big Curve Washer
2 PCS

9
STEP 2
Install two Adjustable Levelers (32) with two Hexagon Nuts (30) onto the Rear Stabilizer (7).
STEP 3
Position the Rear Stabilizer (7) behind the Main Frame (1) and align bolt holes.
Attach the Rear Stabilizer (7) onto the rear curve plate of the Main Frame (1) with two
Carriage Bolts (31), two Big Curve Washers (33), and two Cap Nuts (34). Tighten cap nuts
with the Multi Hex Tool with Phillips Screwdriver provided.
Hardware:
33
34
31
7
1
34
33
31
33
34
31
7
1
(31) Carriage Bolt
2 PCS
(34) Cap Nut
2 PCS
(33) Big Curve Washer
2 PCS
30
32
7

10
STEP 4
Remove three Nylon Nuts (36) and three Washers (37) from underside of the Seat
Cushion (48). Remove nylon nuts with the Multi Hex Tool with Phillips Screwdriver
provided.
Guide bolts on underside of the Seat Cushion (48) through holes on top of the Seat Sliding
Tube (4), attach with three removed Nylon Nuts (36) and Washers (37). Tighten nylon nuts
with the Multi Hex Tool with Phillips Screwdriver provided.
STEP 5
Remove one Washer (69) and one Seat Adjustment Knob (45) from underside of the Seat
Sliding Tube (4). Guide Seat Sliding Tube Bolt (46) on underside of the Seat Sliding Tube
(4) through hole on top of the Seat Post (3), attach with one removed Washer (69) and one
Seat Adjustment Knob (45).
48
37
36
4
48
37
36
37
36
46
48
69
45
4
4
46
69
45
3

11
STEP 6
Slide the Seat Post Cover (44) onto the tube of the Main Frame (1).
Insert the Seat Post (3) into the Seat Post Bushing (43) on the tube of the Main Frame (1)
and then attach the Seat Post Knob (42) onto the tube of the Main Frame (1) by turning it in a
clockwise direction with Multi Hex Tool provided to lock the Seat Post (3) in the suitable
position.
44
43
3
1
42
42
1
3
44

12
STEP 7
Pull both Sensor Wire (56) and Tension Cable (67) out from the tube of the Main Frame (1).
Remove four Hexagon Socket Pan Head Cap Bolts (52), four Washers (37), one Hexagon
Socket Pan Head Cap Bolt (53), and one Curve Washer (54) from the tube of the Main
Frame (1). Remove bolts with the Allen Wrench provided.
STEP 8
Slide the Handlebar Post Cover (55) up to the Handlebar Post (2).
52
37
53 54 1
1
1
56
67
55
255
2

13
STEP 9
It is recommended to have a second person assist with this step. One person should hold
the Handlebar Post (2) in place while the other person to insert and connect the wires.
Insert the Tension Cable (67) through into the bottom hole of the Handlebar Post (2) and pull
it out from the top end of the Handlebar Post (2).
Connect the Sensor Wire (56) from the Main Frame (1) to the Extension Sensor Wire (66)
from the Handlebar Post (2).
66
66
55
2
1
56
67
56
66
55
2
1
67

14
STEP 10
Insert the Handlebar Post (2) onto the tube of the Main Frame (1) and secure with four
Hexagon Socket Pan Head Cap Bolts (52), four Washers (37), one Hexagon Socket Pan
Head Cap Bolt (53), and one Curve Washer (54) from the tube of the Main Frame (1).
Tighten bolts with the Allen Wrench provided.
Slide the Handlebar Post Cover (55) down to the Handlebar Post (2).
STEP 11
Insert the Hand Pulse Sensor Wires (61) and the Wire Grommet (73) through into the hole
on the Handlebar Post (2). Then pull the Hand Pulse Sensor Wires (61) out from the top
end of the Handlebar Post (2).
55
2
52
37
53 54
1
52 37
2
1
55
2
5
61
66
67
61
66
67
2
73
73
61
73
5
5

15
STEP 12
Place the Adjustable Handlebar (5) through clamp on the Handlebar Post (2) with hand
pulse sensors facing the seat.
Hold the Adjustable Handlebar (5) in desired position and fasten Clamp Cover (65), Spacer
(64), and Handlebar T-Knob (63) onto clamp. Tighten the Handlebar T-Knob (63) after
adjustment.
STEP 13
Remove one Cross Recessed Pan Head Tapping Bolt (71) and one Big Washer (72) from
the Tension Control Knob (50). Remove bolt with the Multi Hex Tool with Phillips
Screwdriver provided.
2
2
2
5
5
5
65
64
63
65
64
63
61
50
72
71

16
STEP 14
Remove four Cross Recessed Pan Head Bolts (51) from the Computer (49). Remove bolts
with the Multi Hex Tool with Phillips Screwdriver provided.
STEP 15
Insert the Tension Control Knob (50) into the hole on the Computer (49).
Attach the Tension Control Knob (50) into the Computer (49) with one Cross Recessed Pan
Head Tapping Bolt (71) and one Big Washer (72) that were removed. Tighten bolt with the
Multi Hex Tool with Phillips Screwdriver provided.
49
51
49
49
49
72
71
50
50
72
71
50

17
STEP 16
It is recommended to have a second person assist with this step. One person should hold
the Computer (49) in place while the other person to connect the wires.
Connect the Hand Pulse Sensor Wires (61) and Extension Sensor Wire (66) to the wires that
come from the Computer (49).
Put the cable end of resistance cable of Tension Control Knob (50) into the cable lock of
Tension Cable (67), see Figure A.
Pull the resistance cable of Tension Control Knob (50) up and force it into the slot of metal
bracket of Tension Cable (67), see Figure B.
Insert the metal fitting on the resistance cable of Tension Control Knob (50) into the hole at
the end of the slot in the metal bracket of Tension Cable (67), see Figure C.
Connect the resistance cable of Tension Control Knob (50) to Tension Cable (67) complete,
see Figure D.
Tuck wires into the Handlebar Post (2).
A
B
C
D
50
67
50
50
50
67
67
67
61
67
66 49
50
66
61
4949
49
61
66
2
2

18
STEP 17
Attach the Computer (49) onto the top end of the Handlebar Post (2) with four Cross
Recessed Pan Head Bolts (51) from the Computer (49) that were removed. Tighten bolts
with the Multi Hex Tool with Phillips Screwdriver provided.
49
2
2
49
51
51

19
STEP 18
The Foot Pedals, Pedal Shafts and Pedal Straps are marked “R” for Right and “L” for
Left.
Select the Left Foot Pedal Strap (10) which has L marked on the side of the strap. Snap the
three hole end of the strap onto the inside edge of the Left Foot Pedal (10). Snap the other
end of the strap onto the outside edge of the Left Foot Pedal (10). Select adjustment holes
which allow your foot to be easily removed from the foot pedal.
Use the same procedure to snap the Right Foot Pedal Strap (11) onto the Right Foot Pedal
(11).
Insert the pedal shaft of Left Foot Pedal (10) into threaded hole in the left Crank (14). Turn
the pedal shaft by hand in the counter-clockwise direction until snug.
Note: DO NOT turn the pedal shaft in the clockwise direction, doing so will strip the
threads.
Tighten the pedal shaft of Left Foot Pedal (10) with the Multi Hex Tool with Phillips
Screwdriver provided.
Insert pedal shaft of Right Foot Pedal (11) into threaded hole in right Crank (14). Turn the
pedal shaft by hand in the clockwise direction until snug. Tighten pedal shaft of Right Foot
Pedal (11) with the Multi Hex Tool with Phillips Screwdriver provided.
1
10
11
14
Left Foot Pedal Right Foot Pedal
11
11
10
10