Life Gear 26280 User manual

FORMULA II ,
MAGNETIC RECUMBENT BIKE
ITEM NO: 26280
OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without notice.
2014, Dec.

1
TABLE OF CONTENTS
WARRANTY ------------------------------------------------------------------------------- 1
SAFETY INSTRUCTIONS ------------------------------------------------------------- 2
PARTS LIST ------------------------------------------------------------------------------- 3
HARDWARE PACKING LIST --------------------------------------------------------- 4
TOOLS -------------------------------------------------------------------------------------- 4
OVERVIEW DRAWING -----------------------------------------------------------------5
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 6
OPERATING THE COMPUTER ------------------------------------------------------ 13
ADJUSTMENTS -------------------------------------------------------------------------- 15
MAINTENANCE -------------------------------------------------------------------------- 16
TROUBLESHOOTING ------------------------------------------------------------------ 16
WARM UPAND COOL DOWN ROUTINE ----------------------------------------- 17
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it
has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's
obligation under this warranty is limited to replacing or repairing, free of charge, any parts
which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is extended only to the original owner and is not transferable.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

2
SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following safety
instructions when using this equipment: Read all instructions before using this
equipment.
1. Read all the instructions in this manual and do warm up exercises before using this
equipment.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercise of every
position of the body is necessary. Refer to Warm Up and Cool Down Routine page.
After exercise, relaxation of the body is suggested for cool-down.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that might catch any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult an Authorized
Service Representative.
6. Do not use the equipment outdoors.
7. This equipment is for household use only.
8. Only one person should be on the equipment while in use.
9. Keep children and pets away from the equipment while in use. This machine is
designed for adults only. The minimum free space required for safe operation is not
less than two meters.
10. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
11. The maximum weight capacity for this product is 110 kgs.
WARNING:Before beginning any exercise program consult your physician.
This is especially important for the persons who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness
equipment.
CAUTION:Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

3
PARTS LIST
No. Description Qty No. Description Qty
001 Front Main Frame 1 030 Cap Nut M8 6
002 Front Stabilizer Ø60x1.5x350 1 031 Flywheel Ø230 1
003 Rear Stabilizer Ø60x1.5x430 1 032 Bearing Cup 2
004 Idle Wheel Bracket 1 033 Bearing 2
005 Back and Seat Support Bracket 1 034 Bearing Nut I 15/16" 1
006 Adjustable Leveler M10 2 035 Bearing Nut II 7/8" 1
007 Front Post 1 036 Washer Ø40xØ24x3.0 1
008 Rear Handlebar 1 037 Washer Ø34.5xØ23x2.5 1
009 Tension Bracket 2 038 Hexagon Nut 7/8" 1
010 Washer Ø16xØ8x1.5t 22 039 Belt Pulley with Crank Ø240 1
011 Spring Ø17x62xØ2.5 1 040 Bolt M5x20mm 1
012 Rear Left Stabilizer End Cap 1 041 Washer Ø5 1
013 Rear Right Stabilizer End Cap 1 042 Bolt M5x10mm 4
014 Washer Ø20xØ8x2.0t 7 043 Rear Handlebar Foam Grip
Ø30xØ24x510 2
015 Bushing 2 044 Left Foot Pedal (YH-30X) 1
016 Spring Washer Ø6 2 045 Right Foot Pedal (YH-30X) 1
017 Carriage Bolt M8x70mm 4 046 Rear Handlebar Round End Cap
Ø25 4
018 Nut M10 2 047 Cover Cap Ø40xØ25x10 2
019 Bolt M8x15mm 13 048 Round Knob M16 1
020 Bolt M8x18mm 1 049 Hand Pulse Sensor with Wire
(750mm) 2
021 Eyebolt M6x36 2 050 Sensor with Wire (750mm) 1
022 Idle Wheel Ø10xØ35 1 051 Left Shroud 1
023 Screw ST2.9x12mm 2 052 Right Shroud 1
024 Screw ST4.2x20mm 4 053 Triangle Knob M12 1
025 Screw ST4.2x25mm 10 054 Tension Control Knob 1
026 Phillips Self Tapping Screw
ST4.2x25mm 6 055 Tension Cable L=1150mm 1
027 Nylon Nut M8 2 056 Front Left Stabilizer End Cap Ø60 1
028 Nut M6 2 057 Front Right Stabilizer End Cap Ø60 1
029 Nut M10x1.0x10t 2 058 Front Post Cover 1

4
PARTS LIST
No. Description Qty No. Description Qty
059 Back Cushion 1 069 Bolt M8x45mm 2
060 Belt PJ360 J6 1 070 Bolt M6x15mm 8
061 Seat Cushion 1 071 Washer Ø18xØ6x1.5t 8
062 Computer (HR-1586) 1 072 Backrest and Seat Support Bracket
End Cap 1
063 Sensor Extension Wire (600mm) 1 073 Front Handlebar Foam Grip
Ø30xØ24x150 2
064 Rear Main Frame 1 074 Bolt M8x10mm 4
065 Seat Sliding Tube 1 075 Bolt M8x30mm 2
066 Left Rear Main Frame Cover 1 076 Hand Pulse Sensor Extension Wire
A (1000mm) 1
067 Right Rear Main Frame Cover 1 077 Hand Pulse Sensor Extension Wire
B (1000mm) 2
068 Wire Plug Ø12.1 2 078 Hand Pulse Sensor Extension Wire
C (600mm) 2
HARDWARE PACKING LIST
TOOLS
Allen Wrench S6
1 PC Multi Hex Tool with Phillips Screwdriver
1 PC
(10) Washer
Ø16xØ8x1.5t
2 PCS
(14) Washer
Ø20xØ8x2.0t
6 PCS
(17) Carriage Bolt
M8x70mm
4 PCS
(30) Cap Nut M8
6 PCS (69) Bolt M8x45mm 2 PCS

5
27
10
24
49
10 19
19 10
19
10
19
78
78
77
77
76
76
75
74
73
73
72
71
71
70
70
59
69
68
68
67
66
65
64
53
15
15
63
63
55
61
48
27
58
42
11
8
49
5
43
25
26
26
7
41 40
54
46
46
46
46
10
10
62
10
10
10
10
19
19
19
24
24
24
20
22
4
60
39
45
44
36 34
32
32
33
33 35 37 38
28 16 9
29
29
21
21
31
1
30
30
30
14
14
14
14
13
12
57
56
3
2
18
17
17
50
23
6
51
47
25
25
26
52
47
26
OVERVIEW DRAWING

6
ASSEMBLY INSTRUCTIONS
1. Rear Main Frame Installation
Remove two M8x30mm Bolts (75), four M8x15mm Bolts (19), and six Ø16xØ8x1.5t
Washers (10) from the Rear Main Frame (64). Remove bolts with the S6 Allen Wrench
provided.
Connect the Hand Pulse Sensor Extension Wire A (76) from the Rear Main Frame (64)
to the Hand Pulse Sensor Extension Wire B (77) from the Front Main Frame (1).
Attach the Rear Main Frame (64) into the Front Main Frame (1) with two M8x30mm Bolts
(75), four M8x15mm Bolts (19), and six Ø16xØ8x1.5t Washers (10) that were removed.
Tighten bolts with the S6 Allen Wrench provided.
77
76
75
64
10
10
19
19 1
Allen Wrench S6
Tool:

7
2. Front and Rear Stabilizers Installation
Install two Adjustable Levelers (6) with two M10 Nuts (18) onto the Rear Stabilizer (3).
Position the Front Stabilizer (2) in front of Front Main Frame (1) and align bolt holes.
Attach the Front Stabilizer (2) onto the front curve of the Front Main Frame (1) with two
M8x70mm Carriage Bolts (17), two Ø20xØ8x2.0t Washers (14), and two M8 Cap Nuts (30).
Tighten cap nuts with the Multi Hex Tool with Phillips Screwdriver provided.
Position the Rear Stabilizer (3) behind the Rear Main Frame (67) and align bolt holes.
Attach the Rear Stabilizer (66) onto the rear curve of the Rear Main Frame (64) with two
M8x70mm Carriage Bolts (17), two Ø20xØ8x2.0t Washers (14), and two M8 Cap Nuts (30).
Tighten cap nuts with the Multi hex Tool with Phillips Screwdriver provided.
Hardware:
4 Washers (Ø20xØ8x2.0t)
4 Carriage Bolts (M8x70mm) 4 Cap Nuts (M8)
Tool:
Multi Hex Tool with Phillips Screwdriver
17
6
18
3
14
30
17
2
14
30
1
64

8
3. Front Post, Front Post Cover, and Tension Control Knob Installation
Remove four M8x10mm Bolts (74), four Ø16xØ8x1.5t Washers (10), one Ø20xØ8x2.0t
Washer (14), and one M8x15mm Bolt (19) from the Front Main Frame (1). Remove bolts
with the S6 Allen Wrench provided.
Slide the Front Post Cover (58) up to the Front Post (7).
Insert the Tension Cable (55) through into the bottom hole of Front Post (7) and pull it out
from the square hole of Front Post (7).
Connect the Sensor Wire (50) and Hand Pulse Sensor Extension Wires B (77) from the
Front Main Frame (1) to the Sensor Extension Wire (63) and Hand Pulse Sensor Extension
Wires C (78) from the Front Post (7).
Insert the Front Post (7) onto the tube of the Front Main Frame (1) and secure with four
M8x10mm Bolts (74), four Ø16xØ8x1.5t Washers (10), one Ø20xØ8x2.0t Washer (14), and
one M8x15mm Bolt (19) that were removed. Tighten bolts with the S6 Allen Wrench
provided.
Slide the Front Post Cover (58) down to the Front Post (7).
Remove the Ø5 Washer (41) and M5x20mm Bolt (40) from the Tension Control Knob (54).
Remove bolt with the Multi Hex Tool with Phillips Screwdriver provided.
Put the cable end of resistance cable of Tension Control Knob (54) into the spring hook of
Tension Cable (55) as shown in drawing A of figure 3. Pull the resistance cable of Tension
Control Knob (54) up and force it into the gap of metal bracket of Tension Cable (55) as
shown in drawing B of figure 3. Attach the Tension Control Knob (54) onto the Front Post (7)
with the Ø5 Washer (41) and M5x20mm Bolt (40) that were removed. Tighten bolt with the
Multi Hex Tool with Phillips Screwdriver provided.
1
74 10
50
78
77
74
63
55
58
7
41 40
54
10
19
14
55
54
54
55
BA
Allen Wrench S6
Tool:
Multi Hex Tool with Phillips Screwdriver

9
4. Left and Right Foot Pedals Installation
The Cranks, Foot Pedals, Pedal Shafts and Pedal Straps are marked “R” for Right and
“L” for Left.
Insert the pedal shaft of Left Foot Pedal (44) into threaded hole in the left Crank (39). Turn
the pedal shaft by hand in the counter-clockwise direction until snug.
Note: DO NOT turn the pedal shaft in the clockwise direction, doing so will strip the
threads.
Tighten the pedal shaft of Left Foot Pedal (44) with the Multi Hex Tool with Phillips
Screwdriver provided.
Insert pedal shaft of Right Foot Pedal (45) into threaded hole in right Crank (39). Turn the
pedal shaft by hand in the clockwise direction until snug.
Tighten pedal shaft of Right Foot Pedal (44) with the Multi Hex Tool with Phillips Screwdriver
provided.
39
45
44
Tool:
Multi Hex Tool with Phillips Screwdriver