Life Gear 26590 User manual

METEOR,
MAGNETIC RECUMBENT BIKE
ITEM NO: 26590
OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without notice.
2012, Oct.

1
TABLE OF CONTENTS
WARRANTY ------------------------------------------------------------------------------- 2
IMPORTANT SAFETY INSTRUCTIONS ------------------------------------------- 3
PARTS LIST ------------------------------------------------------------------------------- 4
HARDWARE PACKING LIST --------------------------------------------------------- 5
TOOLS -------------------------------------------------------------------------------------- 5
OVERVIEW DRAWING ----------------------------------------------------------------- 6
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 7
OPERATING THE COMPUTER ------------------------------------------------------ 13
ADJUSTMENTS -------------------------------------------------------------------------- 15
MAINTENANCE -------------------------------------------------------------------------- 16
TROUBLESHOOTING ------------------------------------------------------------------ 16
WARM UP AND COOL DOWN ROUTINE ----------------------------------------- 17

2
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it
has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's
obligation under this warranty is limited to replacing or repairing free of charge, any parts
which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is offered only to the original owner and is not transferable. Proof of
purchase is required.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

3
IMPORTANT SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following important
safety instructions when using this equipment: Read all instructions before using this
equipment.
1. Read all instructions and follow it carefully before using this equipment. Make sure the
equipment is properly assembled and tightened before use.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercise is necessary.
Refer to the Warm Up and Cool Down Routine pages. After exercise, relaxation of the
body is suggested for cool-down.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that might catch any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult your local dealer.
6. Do not use the equipment outdoors.
7. This equipment is for household use only.
8. Only one person at a time should use this equipment.
9. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
10. Care should be taken in mounting or dismounting the equipment.
11. Do not allow children to use or play on the equipment. Keep children and pets away
from the equipment while in use. This machine is designed for adults use only. The
minimum free space required for safe operation is not less than two meters.
12. The maximum weight capacity for this product is 110 kgs.
WARNING: Before beginning any exercise program consult your physician.
This is especially important for the persons who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness
equipment.
CAUTION: Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

4
PARTS LIST
No. Description Qty No. Description Qty
001R Front Right Stabilizer End Cap 1 027 Extension Hand Pulse Sensor Wire
II L=350mm 2
001L Front Left Stabilizer End Cap 1 028 Computer (HR1581) 1
002 Front Stabilizer Ø60x1.5x330 1 029 Bolt M5x10 4
003 Cap Nut M8 4 030 Tension Control Knob 1
004 Big Curve Washer Ø8xØ20x2 7 031 Tension Cable L=1150mm 1
005 Screw ST4.2x25 11 032 Washer Ø5 1
006 Carriage Bolt M8x70 4 033 Bolt M5x20 1
007 Screw ST2.9x16 1 034 Front Post 1
008 Cover Cap 2 035 Bolt M8x10 4
009 Pan Head Phillips Self Drilling
Screw ST4.2x25 6 036 Washer Ø8xØ16x1.5 21
010R Right Cover 1 037 Bolt M8x20 1
010L Left Cover 1 038R Rear Right Stabilizer End Cap 1
011 Belt 360J6 1 038L Rear Left Stabilizer End Cap 1
012R Right Foot Pedal YH-30X 1 039 Idler Arm 1
012L Left Foot Pedal YH-30X 1 040 Nylon Nut M8 1
013 Belt Pulley with Crank 1 041 Front Post Cover 1
014 Washer Ø34.5xØ23x25 1 042 Spring 1
015 Bearing Nut II 7/8" 1 043 Bearing 60002Z 2
016 Ball Bearing 2 044 Middle Section Hand Pulse Sensor
Wire L=1000mm 1
017 Bearing Cup 2 045 Bolt M8x30 2
018 Bearing Nut I 15/16" 1 046 Rear Main Frame 1
019 Hexagon Nut 7/8" 1 047 Seat Cushion 1
020 Flywheel Ø230 1 048 Back Cushion 1
021 Front Main Frame 1 049 Bolt M6x15 8
022 Screw ST2.9x12 2 050 Washer Ø6 8
023 Triangle Knob M12x58 1 051 Back and Seat Support Bracket
End Cap 23x53x1.5 1
024 Handlebar End Cap Ø25x1.5 4 052 Seat Sliding Tube 1
025 Front Handlebar Foam Grip
Ø24xØ30x160 2 053 Back and Seat Support Bracket 1
026 Extension Sensor Wire
L=500mm 1 054 Rear Handlebar Foam Grip Ø24xØ30x510 2

5
PARTS LIST
HARDWARE PACKING LIST
TOOLS
No. Description Qty No. Description Qty
055 Screw ST4.2x20 4 067 Adjustable Leveler M10 2
056 Hand Pulse Sensor with Wire
L=750 2 068 Nut M10 2
057 Bolt M8x45 2 069 Handlebar 1
058 Wire Grommet Ø12.1 2 070 Extension Hand Pulse Sensor Wire
I L=1100mm 2
059 Nut M6 2 071 Sensor with Wire L=750mm 1
060 Round Knob M16x1.5 1 072 Bolt M8x15 13
061 Bushing 2 073 Washer Ø40xØ24x3 1
062R Right Rear Main Frame Cover 1 074 Nut M10x1 2
062L Left Rear Main Frame Cover 1 075 Eyebolt M6x36 2
063 Rear Stabilizer 1 076 Washer Ø14xØ10xδ1.0 2
064 Bolt M8x70 2 077 Washer Ø12xØ6x1t 1
065 Tension Bracket 2 078 Bolt M6x10 1
066 Spring Washer Ø6 2
Allen Wrench S6
1 PC
Multi Hex Tool with Phillips Screwdriver
1 PC
(3) Cap Nut M8
4 PCS
(4) Big Curve Washer Ø8xØ20x2
6 PCS
(6) Carriage Bolt M8x70
2 PCS
(36) Washer Ø8xØ16x1.5
2 PCS
(57) Bolt M8x45
2 PCS
(64) Bolt M8x70
2 PCS

6
OVERVIEW DRAWING
4
67
66
38L
65
4
3
6
63
62R
61
61
9
9
44
58
64
51
53
52
3
36
49
50
50
48
47
46
45
72
36
72
44
42
41
40
39
36
37
36
34
33
32
31
30
29
27
26
28
25
24
20
74
9
21
19
73
18
17
16
17
16
15
14
13
12R
11
10R
8
7
55
55
2
1R
56
55
24
24
54
55
56
58
4
57
68
69
71
22
70
8
54
35
72
5
36
72
59
59
49
5
5
9
9
75
60
23
1L
10L
12L
38R
62L
65
66
75
74
9
5
5
36
72
70
71
25 24
72 36
4
43
76
77 78

7
ASSEMBLY INSTRUCTIONS
1. Rear Main Frame Installation
Remove two M8x30 Bolts (45), four M8x15 Bolts (72), and six Ø8xØ16x1.5 Washers (36)
from the Rear Main Frame (46). Remove bolts with the S6 Allen Wrench provided.
Connect the Middle Section Hand Pulse Sensor Wire (44) from the Rear Main Frame (46)
to the Extension Hand Pulse Sensor Wire I (70) from the Front Main Frame (21).
Attach the Rear Main Frame (46) into the Front Main Frame (21) with two M8x30 Bolts (45),
four M8x15 Bolts (72), and six Ø8xØ16x1.5 Washers (36) that were removed. Tighten
bolts with the S6 Allen Wrench provided.
45
72
36
46
21
36
70
44
72 36
Allen Wrench S6
Tool:

8
2. Front and Rear Stabilizers Installation
Position the Front Stabilizer (2) in front of Front Main Frame (21) and align bolt holes.
Attach the Front Stabilizer (2) onto the front curve of the Front Main Frame (21) with two
M8x70 Bolts (64) and two Ø8xØ20x2 Big Curve Washers (4). Tighten bolts with the S6
Allen Wrench provided.
Position the Rear Stabilizer (63) behind the Rear Main Frame (46) and align bolt holes.
Attach the Rear Stabilizer (63) onto the rear curve of the Rear Main Frame (46) with two
M8x70 Carriage Bolts (6), two Ø8xØ20x2 Big Curve Washers (4), and two M8 Cap Nuts (3).
Tighten cap nuts with the Multi hex Tool with Phillips Screwdriver provided.
Hardware:
(64) Bolt M8x70
2 PCS
(3) Cap Nut M8
2 PCS
(4) Big Curve Washer
Ø8xØ20x2
4 PCS
(6) Carriage Bolt M8x70
2 PCS
Multi Hex Tool with Phillips Screwdriver
Tool:
Allen Wrench S6
2
4
3
6
64
64
4
3
21
46
67
68
4

9
3. Left and Right Foot Pedals Installation
The Cranks, Foot Pedals, Pedal Shafts and Pedal Straps are marked “R” for Right and
“L” for Left.
Insert the pedal shaft of Left Foot Pedal (12L) into threaded hole in the left Crank (13). Turn
the pedal shaft by hand in the counter-clockwise direction until snug.
Note: DO NOT turn the pedal shaft in the clockwise direction, doing so will strip the
threads.
Tighten the pedal shaft of Left Foot Pedal (12L) with the Multi Hex Tool with Phillips
Screwdriver provided.
Insert pedal shaft of Right Foot Pedal (12R) into threaded hole in right Crank (13). Turn the
pedal shaft by hand in the clockwise direction until snug.
Tighten pedal shaft of Right Foot Pedal (12R) with the Multi Hex Tool with Phillips
Screwdriver provided.
12R
12L
13
Multi Hex Tool with Phillips Screwdriver
Tool: