Lightmybricks LEGO Jurassic Park T.Rex Rampage 75936 Lighting... User manual

Light My Bricks: LEGO Jurassic Park – T.Rex
Rampage 75936 Lighting Kit
The following page is the instructions for the Light My Bricks LEGO Jurassic
Park – T.Rex Rampage (75936) LED light kit.
If you run into any issues, please refer to the online troubleshooting guide.

To ensure a trouble-free installation of your light kit, please read and follow
each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are
wishing to purchase the Light My Bricks LEGO Jurassic Park – T.Rex Rampage
(75936) LED light kit , please click here to view the product page
Package Contents:
12x White 30cm Bit Lights
25x White 15cm Bit Lights
5x Green 30cm Bit Lights
2x Flashing White 15cm Bit Lights
2x White Strip Lights
4x 6-Port Expansion Boards
5x 8-Port Expansion Boards
2x Flicker Effects Boards
5x 5cm Connecting Cables
3x 15cm Connecting Cables
3x 30cm Connecting Cables
1x 50cm Connecting Cable
18x Adhesive Squares
1x USB Power Cable
LEGO Pieces:
7x Black Tile 1×1 with Clip
4x Black 1×1 Modified Plate Rounded with Handle
4x Black Round Plate 1×1 with open stud
3x Technic Brick 1×1 with hole (Black or Grey)

3x Black Technic Pin with Friction Ridges Lengthwise with Centre
3x Black Speargun Minifig Weapon
1x Trans Clear Plate w Rounded Bottom 2×2
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles
providing they are laid correctly between the LEGO® studs. Do NOT forcefully
join LEGO® together around cables; instead ensure they are laying comfortably
in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the
cable and light.

Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards.
Connectors can be inserted only one way. With the expansion board facing up,
look for the soldered “=” symbol on the left side of the port. The connector side
with the wires exposed should be facing toward the soldered “=” symbol as you
insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port
or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up, ensure
the side of the connector with the wires exposed is facing down. If a plug won’t
fit easily into a port connector, don’t force it. Doing so will damage the plug and
the connector.

Connecting Micro Cable connectors to Micro
Expansion Board Ports
Take extra care when inserting the micro connectors to micro ports of Micro
Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is
similar to connecting lights and cables to Strip Lights. With the expansion
board facing up, ensure the side of the connector with the wires exposed is
facing down. If a plug won’t fit easily into a port connector, do not force it. Use
your fingernail to push the plastic part of the connector to the micro port.
Installing Bit Lights under LEGO® bricks
and plates.

When installing Bit Lights under LEGO® pieces, ensure they are placed the
correct way up (Yellow LED component exposed). You can either place them
directly on top of LEGO® studs or in between.
OK, Let’s Begin!
1.) First disconnect the front wall panels as well as the fire sections from the
right side of the entrance.

Next, take out the following provided LEGO pieces shown below:
2x Black Tile 1×1 with Clip
2x Black 1×1 Modified Plate Rounded with Handle
2x Black Round Plate 1×1 with open stud

2.) Take one of the black round plates with open stud and thread the connector
end of a Green 30cm Bit Light through the bottom of the black plate. Thread it
all the way through, then slightly bend the Bit Light on a 90 degree angle so
that it can sit flat against the bottom of the black round plate as per below:

Connect this piece to one of the Black 1×1 Modified Plate Rounded with Handle
pieces, then thread the connector side of the cable through the space just
above the handle. Pull the cable all the way out from the other side, then attach
the plate with clip at the bottom.