Lightronics FXLE3030W User manual

Page 1 of 4
FXLE3030W LED FIXTURE
Version 1.0 OWNERS MANUAL 09/23/2019
www.lightronics.com
Lightronics Inc. 509 Central Drive, Virginia Beach, VA 23454 757 486 3588
FEATURES AND SPECIFICATIONS
LEDs: 300 Watt Array (Warm White)
Color Temperature: 3000 K
Beam Angle: 19º, 26º or 36º (50º Optional)
Control System: DMX512 + Stand Alone
DMX Channels: 1 or 2
DMX Connectors: 3 pin XLR I/O
Power Input: 100-230VAC, 50/60Hz
Max. Power Consumption: 300 Watts
Body Material: All Metal Construction
Body Color: Black or White Available
Reflector: Glass
Gel Frame and Size "M" Gobo Holder Included
FX Accessory Slot
Sliding Yoke Assembly on 12.75” Track
Size: 28"L x 13.5"W x 20"H (with yoke)
Weight: 23 lbs
DESCRIPTION
The FXLE3030W is an LED ellipsoidal fixture that is
suitable for stage, houses of worship, entertainment
venues and other artistic applications. It has automatic
stand-alone control modes and can operate via an
external DMX512 signal.
A mounting yoke enables the fixture to be installed and
operated in various positions and orientations.
INSTALLATION
LOCATION
The FXLE3030W is rated IP20 and is intended for
INDOOR USE ONLY.
Locate the unit in a well-ventilated area away from
moisture or heat. Maintain a minimum spacing of 20"
between the unit and other objects. The maximum
ambient operating temperature is 40ºC (104ºF). Keep
the vent holes clear. Holes are provided on the yoke to
install a traditional lighting c-clamp for mounting on
batten pipe. Use a safety cable attached to the safety
eye when hanging the fixture.
GOBO/FX SLOT ALIGNMENT
To rotate barrel, loosen the two 3mm hex socket cap
screws on both sides of body behind shutter handles.
Loosen both adjustment knobs at top and bottom of
fixture behind the shutter handles. Once GOBO or FX
slot is aligned, retighten screws and knobs.
YOKE ADJUSTMENT
To slide yoke along track, loosen 4 screws on both
side brackets with a #2 Phillips screwdriver, adjust
yoke and retighten screws once in desired location.
POWER CONNECTIONS
The FXLE3030W has a line cord for connection to a
100-230VAC, 50/60Hz, grounded service. Do not
power the unit from a dimmer pack.
When using 120VAC, only connect a maximum of
four FXLE3030W fixtures together with power
connectors.
The safety ground pin on the power cord must be
used.
DMX CONNECTIONS
A system using DMX control should be connected as a
chain of devices. In other words the control signal
cable should originate at the controller to the first
receiving device and then to others in a continuous
"daisy chain" fashion. An optically isolated DMX splitter
is recommended when installing the FXLE3030W in a
system with various other DMX devices.
DANGER
RISK OF ELECTRIC SHOCK

Page 2 of 4
FXLE3030W LED FIXTURE
Version 1.0 OWNERS MANUAL 09/23/2019
www.lightronics.com
Lightronics Inc. 509 Central Drive, Virginia Beach, VA 23454 757 486 3588
The FXLE3030W has a DMX IN and a DMX OUT
connector which are used to connect the DMX data
chain. The control cable can NOT be split into a Y or
multiple run/star arrangement with a cable running
directly from the controller to each receiving device.
DMX CONNECTOR PIN ASSIGNMENTS
Predominantly two connectors are used for connecting
fixtures and other DMX devices to a DMX control
chain. They are both “XLR type”connectors. Some
units use 3 pin connectors, others use 5 pin
connectors. The FXLE3030Wreceives a DMX signal
on the 3 pin MALE connector on the rear of the unit.
The 3 pin FEMALE connector is used to connect to the
next DMX device on the control chain.
If your console uses a 5 pin XLR connector, an adapter
cable can be purchased or fabricated to accommodate
this conversion. The following table shows the pin
assignments for both 3 pin and 5 pin XLR connectors:
DMX TERMINATION
It is recommended that a DMX data chain be
terminated at the last receiving device on the chain.
This is done by installing a commonly available 1/4
Watt, 120 Ohm resistor across the DATA - and DATA
+ wires at the last device. If you have only a few
fixtures installed very close together and with a short
run of DMX cable to the controller then you may be
able to operate without the terminator.
OPERATION
Power is applied once the power cord is connected to
a live power source. There is not an on/off switch.
Connect power cord to fixture first, then outlet. A
display and user interface is located on the back of the
unit. This interface is used to set the operating options
and settings. It consists of a backlit LCD display and
four buttons (MODE, DOWN, UP, and ENTER).
Use MODE to scroll through the available choices.
Push ENTER when you reach the option you want to
check or set. The current setting for the option will be
shown. Use UP and DOWN until you reach the
desired setting or menu then push ENTER to invoke
the new setting. Use ENTER to exit from the sub
menus.
DMX OPERATION
Use the DMX-Addr menu to set the unit DMX starting
address. The range is 001 - 512. A ‘V’will be
displayed if a valid DMX signal is present, an ‘x’
represents that no valid DMX signal is present.
For this fixture to operate in DMX mode, the mode
needs to be set for “DMX-Addr” on LCD display by
pressing the MODE button.
The fixture has 2 DMX modes. One channel and 2
channel: Channel 2 is not active in 1 channel mode.
CHANNEL 1: Fixture Intensity (000 - 255)
CHANNEL 2: Strobe Control (000 - 127, 128-255)
000 is Strobe OFF, starts slow and
increases to fastest at 127. From 128-
255 pattern transitions to short light
pulses with longer duration between
pulses as value rises from 128 to 255.
STAND ALONE MODE
You can operate the unit manually using the R-
DIMMER & P-STROBE menu. Use the UP and
DOWN buttons to change the level, Push ENTER
when done. The range is 000 - 255 (See above for
values).
DMX-KEEP: ON/OFF
The DMX-KEEP mode determines the characteristic of
the fixture upon the loss of the DMX input signal. The
LED array will either turn on or off based on the DMX-
KEEP setting when DMX signal is lost.
PIN #
SIGNAL NAME
1
DMX COMMON
2
DMX DATA -
3
DMX DATA +
4
NOT USED
5
NOT USED
MODE
ENTER
UP
P
DOWN
CONTROL PANEL

Page 3 of 4
FXLE3030W LED FIXTURE
Version 1.0 OWNERS MANUAL 09/23/2019
www.lightronics.com
Lightronics Inc. 509 Central Drive, Virginia Beach, VA 23454 757 486 3588
BK-LIGHT: ON/OFF
The backlight for the LCD display remains on at all
times if this function is set to ON. When Backlight is set
to OFF, then the backlit display will turn off 30 seconds
after the last button push on the control panel.
NOW TEMP
Provides operating temperature in ºC.
MAINTENANCE AND REPAIR
TROUBLESHOOTING
Fixture will not power up.
Check that you have power applied to the
unit.
Check the fuse located on the back panel of
the fixture.
Unable to control fixture.
Check that the LCD display currently
indicates “DMX-addr”.
Check the LCD display on the fixture; if there
is a V after the DMX value, a valid DMX
signal is present. If an ‘x’ is showing, then a
valid DMX signal is not present.
Verify that the fixture is properly addressed.
Check the DMX control cable for continuity
and polarity.
Remove the fixture from the DMX chain and
all other DMX devices.
Check the address settings or patch at the
controller.
CLEANING
DISCONNECT THE POWER CORD BEFORE
HANDLING THE UNIT.
A mild detergent can be used sparingly if needed.
Apply to cloth first; do not apply detergents directly to
fixture. Do not use chemicals or solvents when
cleaning the fixture. Ensure that the unit is dry before
use.
REPAIR
The only FXLE3030W user serviceable part is a 5 mm
x 20 mm externally accessible fuse on the rear panel.
DISCONNECT THE POWER CORD BEFORE
CHECKING OR REPLACING THE FUSE.
Replace fuse ONLY with 5.0 Amp, 250VAC, fast acting
fuse.
Internal service on the unit by other than Lightronics
authorized agents will void the warranty.
If service is required, contact the dealer from whom
you purchased the item, or contact the Lightronics,
Service Department, 509 Central Drive, Virginia Beach,
VA 23454. Tel: [phone].
FXLE3030W
10 Foot
20 Foot
30 Foot
Beam (ft.)
FC
Lux
Beam (ft.)
FC
Lux
Beam (ft.)
FC
Lux
19°
2.5
2150
23200
5
537.5
5800
7.5
239
2578
26°
4.75
1039
10960
9
279
2950
13.5
125
1345
36°
6.33
533
5740
12.6
143
1545
19
65.4
704
50°
9
279
3000
18
75
807
27
34
368
DANGER DO NOT OPEN UNIT
RISK OF ELECTRIC SHOCK
RISK OF FIRE
PHOTOMETRIC CALCULATIONS

This product is warranted for a period of TWO YEARS from the date of purchase against
defects in materials and workmanship.
This warranty is subject to the following restrictions and conditions:
A) If service is required, you may be asked to provide proof of purchase from an
authorized Lightronics dealer.
B) This warranty is valid only for the original purchaser of the unit.
C) This warranty does not apply to damage resulting from abuse, misuse, accidents,
shipping, and repairs or modifications by anyone other than an authorized
Lightronics service representative.
D) This warranty is void if the serial number is removed, altered or defaced.
E) This warranty does not cover loss or damage, direct or indirect arising from the use or
inability to use this product.
F) Lightronics reserves the right to make any changes, modifications, or updates as
deemed appropriate by Lightronics to products returned for service. Such changes
may be made without prior notification to the user and without incurring any
responsibility or liability for modifications or changes to equipment previously
supplied. Lightronics is not responsible for supplying new equipment in accordance
with any earlier specifications.
G)This warranty is the only warranty either expressed, implied, or statutory, upon which
the equipment is purchased. No representatives, dealers or any of their agents are
authorized to make any warranties, guarantees, or representations other than
expressly stated herein.
H) This warranty does not cover the cost of shipping products to or from Lightronics for
service.
I) Lightronics Inc. reserves the right to make changes as deemed necessary to this
warranty without prior notification.
Lightronics Inc. 509 Central Drive Virginia Beach, VA 23454 20100211
WARRANTY