Lightronics FXPAR4 User manual

Page 1 of 3
FXPAR4 MULTIPLE LENS PAR FIXTURE
Version 1.1 OWNER’S MANUAL 02/08/2022
www.lightronics.com
Lightronics Inc. 509 Central Drive, Virginia Beach, VA 23454 757 486 3588
FEATURES AND SPECIFICATIONS
Power Supply: 120 VAC, 60 Hz
Power Consumption: 800 Watts MAX
Lamp:OSRAM GLA/575 or GLE/750 (G9.5 Base)
Maximum Ambient Temperature: 113° F/45° C
Maximum Housing Temperature: 320° F/160° C
Dimensions: 10” D x 11” W x 11.4” H
255mm D x 280mm W x 290mm H
Weight: 8.8 lbs. / 4 kg
DESCRIPTION
This manual contains important information about
safe installation and use of the FXPAR4 fixture.
Please read these instructions completely before
energizing. Follow these instructions carefully and
keep this manual for future reference.
The FXPAR4 is suitable for stage, disco, night club,
and other artistic applications.
The housing is a high quality aluminum alloy with an
insulating paint finish.
The FXPAR4 includes a lens rotation ring to enable
beam adjustments. A gel filter holder is also
provided. The product complies with CE norms and
standards.
The fixture is supplied with four interchangeable high
quality lenses to cover various lighting applications.
INSTALLATION
MOUNTING
Make sure that all power is disconnected from
the fixture before proceeding.
The fixture is for INDOOR USE ONLY. Use only in
dry locations. Keep this device away from moisture,
excessive heat, humidity and dust. Do not mount the
fixture directly on or to a flammable surface.
Maintain a 5 foot/1.5 meter clearance from
flammable objects.
The fixture must be installed in a location with
adequate ventilation, at least 5 feet/1.5 meters from
adjacent surfaces. Do not allow vent holes to be
blocked.
This unit is designed to be hung via its yoke using
M12 or 1/2" size bolt. Ensure that the fixture is firmly
attached to avoid vibration and slipping. Ensure that
the supporting structure is able to support the weight
of all fixtures installed. The unit should also be
secured with a safety cable through one of the holes
on the yoke.
To adjust the tilt angle of the body, loosen the yoke
CAUTION RISK OF FIRE
The fixture must be located a
minimum of 5 feet / 1.5 meters
from flammable objects.

Page 2 of 3
FXPAR4 MULTIPLE LENS PAR FIXTURE
Version 1.1 OWNER’S MANUAL 02/08/2022
www.lightronics.com
Lightronics Inc. 509 Central Drive, Virginia Beach, VA 23454 757 486 3588
locking knob and adjust as needed. Ensure that the
locking knob is tightened down when finished.
POWER CONNECTIONS
The unit is supplied with a power cable and may be
provided with a power cable connector. The GREEN
/ YELLOW conductor in the power cable is
connected to the fixture case as a safety ground.
This conductor must be used if installing an alternate
cable connector.
LAMP REMOVAL / INSTALLATION
The FXPAR4 fixture uses an OSRAM GLA/575 or
GLE/750 (G9.5 Base) lamp. Before installing a
lamp, verify that the lamp is compatible with the
voltage at your facility. Operating lamps beyond their
rated voltage reduces lamp life and can cause other
lamp failures.
Disconnect all power from the fixture.
Allow the fixture to cool off before proceeding.
Keep the lamp and lens clean. Do not touch the
lamp or lens with your bare hands.
LAMP REMOVAL
1. Remove the lamp holder from the main housing
using the knurled knob at the rear of the fixture.
2. Do not touch the glass envelope of the lamp.
Remove the lamp from the lamp holder by pulling
it straight out of the lamp holder socket.
LAMP INSTALLATION
1. Remove the lamp holder from the main housing
using the knurled knob at the rear of the fixture.
2. Insert the lamp in the lamp holder socket. Do not
touch the lamp glass envelope with your fingers.
Do not operate the lamp unless the lamp holder
is installed in the fixture!
3. Install the lamp holder in the main housing and
tighten the knob.
LENS REMOVAL / INSTALLATION
The FXPAR4 contains a lens rotation ring which is
located near the front of the housing. The lens is
held in place by two small fixed tabs on one side of
the lens rotation ring and a larger metal release tab
on the other side.
Disconnect all power from the fixture.
Allow the fixture to cool off before proceeding.
Do not remove or install the lens while the unit is
hanging up. The lens can easily fall out if
released.
LENS REMOVAL
1. Place the fixture on a horizontal surface with the
lens down.
2. Turn the lens rotation ring until the metal release
tab is 90º away from the gel retaining clip on the
housing.
3. Hold one hand under the lens and press the
metal release tab to release it. Allow the lens to
carefully drop out of the fixture.
LENS INSTALLATION
1. Place the fixture on a horizontal surface.
2. Turn the lens rotation ring until the metal release
tab is 90º away from the gel retaining clip on the
housing.
3. Slide the one edge of the lens edge under the
fixed tabs on the lens rotation ring.
4. Press the other edge of the lens down until it is
CAUTION
RISK OF ELECTRIC SHOCK
The fixture must be correctly
grounded and must be
installed to comply with all
applicable regulations.
Rotation Ring
Release Tab

Page 3 of 3
FXPAR4 MULTIPLE LENS PAR FIXTURE
Version 1.1 OWNER’S MANUAL 02/08/2022
www.lightronics.com
Lightronics Inc. 509 Central Drive, Virginia Beach, VA 23454 757 486 3588
captured by the metal release tab of the rotation
ring.
OPERATION
The lens and gel holder must be installed when the
fixture is operating.
Avoid direct exposure to the light from the lamp. The
light can be bright enough to harm the eye.
Do not project the beam onto nearby flammable
surfaces. The minimum distance is 16 feet/5 meters.
The lens may be rotated to adjust beam alignment.
This is done by rotating the lens rotation ring located
near the front of the fixture.
Replace the lamp if it is damaged or deformed.
Replace the lens if it is cracked or scratched.
Once correctly installed, the fixture may be operated
by applying power via a dimmer or other compatible
power.
Switching the lamp on and off at short intervals will
reduce the life of both the lamp and the fixture.
MAINTENANCE
To ensure the reliability of the fixture, it should be
kept clean. The lens and reflector should be
regularly cleaned to maintain an optimum light
output.
Do not use any organic solvent, e.g. alcohol, to
clean the housing. Do NOT use glass cleaner or
any type of solvent on the reflector. When cleaning
the reflector use a damp, clean, soft, lint-free cotton
cloth with a mild, soapy water solution and gently
wipe the reflector, and then remove any soapy water
residue with a clean, soft, lint-free cotton cloth.
Do not use rough surface materials to wipe the
reflector. Cleaning frequency depends on the
environment in which the fixture operates. Moisture,
smoke or particularly dirty surroundings can cause
greater accumulation of dirt on the unit’s optics. It is
recommended that the lens be cleaned at least once
every 20 days. Clean the reflector at least once
every 30 / 60 days.
If service is required, contact the dealer from whom
you purchased the item, or contact the Lightronics
Service Department, 509 Central Drive, Virginia
Beach, VA 23454. Tel: [phone].
WARRANTY INFORMATION AND
REGISTRATION – CLICK LINK BELOW
www.lightronics.com/warranty.html
CAUTION
RISK OF ELECTRIC SHOCK
Disconnect the fixture from power
before handling.
CAUTION - HOT SURFACES
Allow the fixture to cool off
before handling.
CAUTION - HOT SURFACES
Do not touch any part of the
fixture during operation. It can
operate at temperatures which
can cause severe burns.
CAUTION: RISK OF
FIRE/ELECTRIC SHOCK
Do not operate the lamp
unless the lamp holder
is installed in the
fixture.