Lincoln 84700 Owner's manual

MODEL 84700
ROLLING OIL DRAIN PAN
SERIES “B”
OWNER/OPERATOR MANUAL
Page
Section - B4 - 37
Form 403897
JUN - 2009
DESCRIPTION
The Model 84700 Rolling Oil Drain Pan is designed to be used
in service pits having 36” to 49-1/2” between the pit walls.
Angle iron tracks must be attached to the sides of the pit
walls for the drain pan to roll on (See TYPICAL SERVICE PIT
DETAILS).
Oil drain pan has a capacity of 30 gallons (23 gallons to bottom
of screen) and is equipped with a 1-1/2” quarter-turn valve.
Drain pan contains a metal screen to eliminate oil splash and
to catch foreign objects such as tools and drain plugs. The
screen can be easily removed for drain pan clean out.
ASSEMBLY INSTRUCTIONS
1. Unpack drain pan and all loose parts.
2. Assemble quarter turn valve (245897) to one end of drain
pan. Assemble pipe cap (245899) to drain tting on oppo-
site end of drain pan.
3. Purchase and install your choice of a 1-1/2” quick discon-
nect tting and hose.
4. To install axle and wheel assemblies to pan, slide each axle
(236474) into the tubes on the drain pan. Slide one sleeve
(236476) on each end of axle (236474). Install locknut
(236473) hand tight on the axle. Install one retaining ring
(70475), one washer (48502) and wheel (236475) to each
end of axle (236474). Secure wheels with one washer
(48502) and one retaining ring (70475).
5. Place drain pan into pit, sliding axles out until the wheels
will roll on tracks. Center pan inside tracks so there is equal
clearance on both sides of drain pan between the pan and
the track. Carefully roll the drain pan from one end of pit to
the other. Axle ends should be adjusted for minimum clear-
ance on both sides of the tracks or pit walls. Wheels must
remain rmly on the tracks and should not leave tracks if
pan is cocked in the pit. After adjusting axles, tighten the
four locknuts (236473) enough to prevent the axles from
moving in the axle tubes. Again, roll the drain pan from one
end of the pit to the other checking for binding or excess
clearance. Readjust axles, if necessary, by loosening the
locknut on the axle to be adjusted and moving the axle in or
out as required. Tighten the four locknuts securely.
NOTE: Once the axle locknuts have been wrench tight-
ened, the tube ends will are out making the axle
nuts harder to turn. This is a self-locking feature
and is normal.
To order call 1-800-548-1191 or visit www.partdeal.com - [email protected]

Page Number - 2 Form 403897
MODEL 84700
ROLLING OIL DRAIN PAN
SERIES “B”
6. Stops should be installed in pit to prevent the valve and
quick disconnect coupler stud from striking the end of the
pit. See END STOP DETAILS.
7. Insert screen (237069) into drain pan.
8. Check all connections for leaks.
Make certain that all four axle locknuts (236473) are
securely tightened before putting drain pan into operation.
RETAIN THIS INFORMATION FOR FUTURE REFERENCE
WHEN ORDERING REPLACEMENT PARTS, LIST: PART NUMBER, DESCRIPTION, MODEL NUMBER, AND SERIES
LETTER. LINCOLN PROVIDES A DISTRIBUTOR NETWORK THAT STOCKS EQUIPMENT AND REPLACEMENT PARTS.
A LIST OF AUTHORIZED SERVICES DEPARTMENTS WILL BE FURNISHED UPON REQUEST.
OPERATION
The normal storage location for Model 84700 Rolling Oil Drain
Pan is at one end of the service pit where a exible hose
(supplied by customer), leading to a central waste oil tank, can
be attached to the pan. Wall bracket, provided, is attached to
the side of the pit for storing the drain hose when not in use.
After the vehicle has been driven over the service pit, position
the drain pan under the vehicle (make sure the quarter-turn
valve is closed). Drain crankcase, roll the drain pan to end of
pit. When the drain pan begins to get full, connect drain hose
to drain pan and open quarter turn valve to drain oil into cen-
tral waste oil tank. Remove the drain hose from the oil drain
pan by pulling upward and outward on the two handles at the
sides of the quick disconnect socket and hang the hose on the
bracket attached to the pit wall.
To order call 1-800-548-1191 or visit www.partdeal.com - [email protected]

Page Number - 3
Form 403897
MODEL 84700
ROLLING OIL DRAIN PAN
SERIES “B”
To order call 1-800-548-1191 or visit www.partdeal.com - [email protected]

Page Number - 4 Form 403897
MODEL 84700
ROLLING OIL DRAIN PAN
SERIES “B”
Americas:
One Lincoln Way
St. Louis, MO 63120-1578
USA
Phone [phone]
Fax [phone]
Europe /Africa/Middle East
Lincoln GmbH
Heinrich-Hertz-Str. 2-8
69190 Walldorf - Germany
Phone/Fax [phone]
www.lincolnindustrial.de
Asia/Pacic:
51 Changi Business Park
Central 2
#09-06 The Signature
Singapore 486066
Phone [phone]
Fax [phone]
© Copyright Lincoln Industrial
Corporation 2009
Printed in USA
Web site:
www.lincolnindustrial.com
Lincoln Industrial Standard Warranty
LIMITED WARRANTY
Lincoln warrants the equipment manufactured and supplied by Lincoln to be free from defects in material and workmanship for a period of one
(1) year following the date of purchase, excluding therefrom any special, extended, or limited warranty published by Lincoln. If equipment is
determined to be defective during this warranty period, it will be repaired or replaced, within Lincoln’s sole discretion, without charge.
This warranty is conditioned upon the determination of a Lincoln authorized representative that the equipment is defective. To obtain repair or
replacement, you must ship the equipment, transportation charges prepaid, with proof of purchase to a Lincoln Authorized Warranty and Service
Center within the warranty period.
This warranty is extended to the original retail purchaser only. This warranty does not apply to equipment damaged from accident, overload,
abuse, misuse, negligence, faulty installation or abrasive or corrosive material, equipment that has been altered, or equipment repaired by anyone
not authorized by Lincoln. This warranty applies only to equipment installed, operated and maintained in strict accordance with the written
specications and recommendations provided by Lincoln or its authorized eld personnel.
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE WARRANTY OF MERCHANTIBILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
In no event shall Lincoln be liable for incidental or consequential damages. Lincoln’s liability for any claim for loss or damages arising out of the
sale, resale or use of any Lincoln equipment shall in no event exceed the purchase price. Some jurisdictions do not allow the exclusion or limitation
of incidental or consequential damages, therefore the above limitation or exclusion may not apply to you.
This warranty gives you specic legal rights. You may also have other rights that vary by jurisdiction.
Customers not located in the Western Hemisphere or East Asia: Please contact Lincoln GmbH & Co. KG, Walldorf, Germany, for your warranty
rights.
Lincoln Industrial Special Limited Warranties
SPECIAL LIMITED 2 YEAR WARRANTY-
SL-V Series, Single Injectors-85772, 85782, and Replacement Injectors-85771, 85781
Lincoln warrants the SL-V Injector series to be free from defects in material and workmanship for two (2) years following the date of purchase. If an
injector model (single or replacement) is determined to be defective by Lincoln, in its sole discretion, during this warranty period, it will be repaired
or replaced, at Lincoln’s discretion, without charge.
SPECIAL LIMITED 5 YEAR WARRANTY-
Series 20, 25, 40 Bare Pumps, PMV Bare Pumps, Heavy Duty and 94000 Series Bare Reels
Lincoln warrants series 20, 25, 40 bare pumps, PMV bare pumps, Heavy Duty (82206), Mini Bench (81133, 81323), and 94000 LFR series (94100,
94300, 94500) bare reels to be free from defects in material and workmanship for ve (5) years following the date of purchase. If equipment is
determined by Lincoln, in its sole discretion, to be defective during the rst year of the warranty period, it will be repaired or replaced at Lincoln’s
discretion, without charge. In years two (2) and three (3), the warranty on this equipment is limited to repair with Lincoln paying parts and labor
only. In years four (4) and ve (5), the warranty on this equipment is limited to repair with Lincoln paying for parts only.
SPECIAL LIMITED 5 YEAR WARRANTY-
LFM Series Oil Meters (Lincoln Fluid Meter), LFV (Lincoln Fluid Valves), AOD (Air-Operated Diaphragm Pumps)-
Lincoln warrants the LFM meter series (908/912 series), the Lincoln Fluid valve (708/712 series), and our AOD Pump offering to be free from
defects in material and workmanship for ve (5) years following the date of purchase. If either is determined to be defective by Lincoln, in its sole
discretion, during the warranty period, they will be repaired or replaced, at Lincoln’s discretion, without charge.
Lincoln Industrial Contact Information
To nd Lincoln Industrial’s Nearest Service Center call the following number, you may also use our website
Customer Service 314-679-4200
Website www.lincolnindustrial.com
To order call 1-800-548-1191 or visit www.partdeal.com - [email protected]