LITESHEET BriteCor AC Direct BSS User manual

BSS BriteCor AC
Direct Damp
Location Stik
Installation Manual

BSE2 BriteCor Damp Location Stik Installation Manual
Page 2of 6
NOTES
•WARNING –Risk of fire or electric shock.
•WARNING - It is recommended that installation be
performed by a certified electrician.
•All electrical connections must be in compliance with
local codes, ordinances or the national electrical code
(NEC). Contact your municipal building department to
learn about your local codes, permits and/or
inspections.
•Do not connect this Luminaire to an electrical system
that does not provide means for equipment grounding.
Never use a fixture in a two-wire system that is not
grounded.
•If dimming functionality is included, use only with
Litesheet approved dimmers.
•Do not use excessive force when manipulating cables
and wires.
•WARNING –To prevent wiring damage or abrasion, do
not pinch wires between surfaces.
•WARNING –Only connect Luminaire to the voltage
indicated by the Luminaire label. It is intended for
direct connection to this voltage. DO NOT connect to a
different or unknown voltage.
Document #: 11-00016
Rev: F
Date: 4/20/2022

LiteSheet Solutions
Page 3of 6
CONTENTS OF KIT
•BriteCor Damp Location Stik luminaire
•Mounting brackets
•(4) M5 x 5mm screws
•(4) T-nuts
TOOLS AND ADDITIONAL PARTS REQUIRED
•Philips head screwdriver
•Mounting screws
Installation
1. Turn off power source.
2. Locate T-nut in channel on extrusion. Line up
either L or flat bracket holes with T-nut holes.
Using a M5 x 5mm screw, attached bracket to
T-nut. Tighten until T-nut rotates in channel.
L-Bracket shown.
3. Use 3 brackets for each 40” Stik module. Use
2 brackets for each 20” Stik module.
4. Use appropriate hardware to mount to final
surface.

BSE2 BriteCor Damp Location Stik Installation Manual
Page 4of 6
Module Combining Calculations
A MODULE is considered a 20” or 40” Stik. MODULES
are used to form ASSEMBLIES. ASSEMBLIES and/or
MODULES have a 12” cable with connector that can
be plugged into one another to form long STRINGS of
lights. STRINGS can be as long as the chart shown.
See chart for maximum STRING length. Contact
LiteSheet for longer ASSEMBLY or STRING lengths.
Stik Module
Stik Assembly
String of lights

LiteSheet Solutions
Page 5of 6
Max String Length @
120vac
Max String Length @
277vac
STIK
75 feet
(Max Modules (21) 40”
or (42) 20” or
combination not to
exceed 75 feet.
170 feet
(Max Modules (50) 40”
or (100 20”) or
combination not to
exceed 170 feet.
1. STRINGS of lights are connected using quick
connectors. Each MODULE or ASSEMBLY will
plug into the next MODULE or ASSEMBLY
with a quick disconnect. Each STRING will
have 3 types of MODULES or ASSEMBLIES - a
starter MODULE or ASSEMBLY which will
have a pigtail to wire to a junction box on one
end, a middle MODULE or ASSEMBLY which
will have a quick connector on both ends and
an end MODULE or ASSEMBLY which will
have a quick connector on one end and an
end plate on the other end. MODULES,
ASSEMBLIES AND STRINGS MUST NOT BE
UNPLUGGED OR PLUGGED TOGETHER
WHILE POWER IS APPLIED.
2. Only the starter MODULE is connected to
power. On the starter MODULE or
ASSEMBLY, secure the pigtail cable using an
UL approved wet location cable gland and a
UL rated wet location electrical box. Use
wire connectors to join power side black wire
to BriteCor module or unit black wire, power
side white wire to BriteCor module or unit
white wires. Connect green wires to ground.

BSE2 BriteCor Damp Location Stik Installation Manual
Page 6of 6
For warranty information and
technical support, contact us at:
434-446-1460
Find more great products at:
www.litesheet.com