Logitech ZONE VIBE 130 User manual

ZONE VIBE 130
Setup Guide
Guide d'installation

CONTENTS
English . . . . . . . . . . . . . . . . .3
Français . . . . . . . . . . . . . . . 12
Español . . . . . . . . . . . . . . . . 21
Português . . . . . . . . . . . . . . 30

KNOW YOUR PRODUCT
Front view:
Back view:
Microphone
boom
Music control button
(play/ pause/
nexttrack)
USB-A
adapter
USB-C
receiver
Call button
(answer/ end/
reject calls)
Volume up / down
3English

Bottom view:
3-position switch (power /
Bluetooth®pairing)
Mute button
USB-C port
LED light
4English

USB-C USB-C USB-AUSB-C
BOX CONTENT
1. Zone Vibe 130 wireless headphones
2. Charging cable
3. USB-C receiver
4. USB-A adapter
5. Travel bag
6. User documentation
POWER ON / OFF
1. Slide the switch in the arrow’s direction to
the middle to power on the headphones.
1
2
2. Once powered on, the LED light will slightly
turn white.
3. There will be a voice prompt that tells you
the battery status.
5English

CONNECT YOUR HEADPHONES
a. Connect via USB-C receiver
1. Insert the receiver into the computer
USB-C port. Or insert the USB-C receiver
with the USB-A adapter to the USB-A port.
2. Zone Vibe 130 is already paired to the
receiver it ships with.
3. Once successfully paired, the LED light on
the receiver will turn solid white then dim.
b. Connect via BLUETOOTH®
1. Slide the switch to the bottom in the arrow’s
direction for 2 seconds to initiate pairing.
2. The LED light will ash white rapidly.
3. Open Bluetooth®settings on your device.
4. Select Logi Zone Vibe 130 in discoverable
devices.
5. Once successfully paired, the LED light will
turn solid white.
LOGI Zone
Vibe 130
2 sec.
USB-C
USB-A
ADJUSTING HEADPHONES
1. Adjust the headphones by sliding earcups
up and down the extended part of the
headband.
2. It may be easier to adjust the headphones
on your head. Slide the earcups up
and down the headband until they sit
comfortably on your ears.
6English

HEADPHONES CONTROLS
Note:
- Media control functionality depends on the type of application.
- Call activities are always the rst priority. When two devices are connected, the Bluetooth®connection will be prioritized
over the receiver. When two Bluetooth®devices are connected, the last active device will override the other.
Tip: Music EQ controls available on Logi Tune.
UC version:
Usage Button Action
Call controls Answer / End call Call button Short press
Reject call 1.5 sec. press
Music controls Play / Pause Music control button Short press
Track forward Double press
Volume Volume up "+" Short press
Volume down "-"
Connectivity Bluetooth®pairing 3-position button 2 sec. press
Voice notications indicate
when the microphone is on /
o mute.
L L L
Mute
"Mute on"
"Mute o"
MUTE
There are 2 ways to mute your microphone.
Press the button to mute. Flip up or down the mic
boom to mute or unmute.
7English

HEADPHONES LIGHT INDICATOR
Note:
- User-triggered behaviors, such as Bluetooth®pairing, will be prioritized then revert back to its previous status once
thebehavior is completed.
Category Status Light
White
Power
Power ON Turn solid white and then dim
Battery charging Breathing
Battery fully charged Solid and then o
Connectivity Bluetooth®pairing Fast blinking
Bluetooth®/ receiver connected Turn solid white and then dim
Calls Active call Solid
Incoming call Slow blinking
Red Calls Mute Solid
Power Low battery (< 10%) Slow blinking
Factory reset Fast blink from red to white for
three times then LED turn o
RECEIVER LIGHT INDICATOR
UC version
Category Status Light
White
Connectivity
Receiver connecting Fast blinking
Receiver connected Turn solid white and then dim
Receiver disconnected O
Calls
Active call Turn solid white and then dim
Incoming call Repeat "fast blinking 3 times then
LED o"
Red Calls Mute Solid
Blue Connectivity New device pairing Fast blinking
New device paired Solid blue then dim white
Connecting mode
Connected
Incoming call
Mute on
Pairing mode
Paired
8English

CHARGING
To conserve battery life, headphones
automatically power o aer 30 minutes
without usage.
Sleep timer can be adjusted in Logi Tune.
The LED light on the headphones will
blinkslowly in RED when the battery is lower
than 10%.
Charging via USB cable
1. Plug one end of the cable to the USB-C port
on the bottom of the earcup and the other
end into the USB-C charging port on your
computer.
2. The LED light will start breathing white when
charging.
3. The LED light will turn solid white when fully
charged.
– 2 hours will fully charge the battery.
– 5 minutes will give you 1 hour of playback.
Note:
Battery life may vary based on user, environment,
andcomputing conditions.
4. The headphones can be used with the receiver
and Bluetooth®paired while charging.
LOGI TUNE
Logi Tune helps boost your headphones
performance with periodic soware
andrmwareupdates.
It is recommended to update both your
headphones and receiver. To do so, download
LogiTune from www.logitech.com/tune
www.logitech.com/tune
Logi Tune
9English

ADJUSTING SIDETONE
Sidetone lets you hear your own voice during conversations
so you are aware of how loud you are talking. In Logi Tune,
select the sidetone feature, and adjust the dial accordingly.
 A higher number means you hear more external sound.
 A lower number means you hear less external sound.
AUTO SLEEP TIMER
By default, your headphones will automatically power o
when not in use for 30 minutes. Adjust the sleep timer in
Logi Tune. To wake up your headphones, try sliding o/on
the power switch again.
RESET YOUR HEADPHONES
1. Power the headphones on.
2. Press and hold the call button and volume ’–’ button
for5seconds.
3. The LED light will quickly blink from red to white for 3 times
and then turns o when your headphones are successfully
reset.
4. The headphones will turn o aer reset.
10 English