LUCCI Air Aria CTC User manual

V1.0 –AU (2019/09)
LUCCI
AIRFUSION ARIA CTC
CEILING FAN
⚫INSTALLATION
⚫OPERATION
⚫MAINTENANCE
⚫WARRANTY INFORMATION
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.

Aria CTC Installation Instructions
1 | P a g e
THANK YOU FOR PURCHASING
Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read
and follow all instructions carefully before assembly, installation and use of this ceiling fan. Please keep
instructions for future reference.
SAFETY PRECAUTIONS
1. In Europe: This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the appliance in a safe way and
understand the hazards involved. Cleaning and maintenance shall not be undertaken by children
without supervision.
2. In Australia: The appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning the use of the appliance by a person responsible
for their safety.
3. Children should be supervised to ensure that they do not play with the appliance.
4. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local
wiring rules.
IN AUSTRALIA
WARNING:
FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION
MUST BE INCORPORATED INTO THE FIXED WIRING IN
ACCORDANCE WITH THE WIRING RULES.
As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting the
minimum electrical safety of this standard.
Please note warranty will be void if installation is without a means for
an all-pole disconnection incorporated in the fixed wiring in
accordance with the wiring rules.
Example: If a fan is connected to a circuit that can be isolated via an

Aria CTC Installation Instructions
2 | P a g e
all-pole safety switch at the switchboard, then this is considered to be
an all-pole disconnection to the ceiling fan electrical circuit, meeting
the requirements of clause 7.12.2 of AS/NZS 60335.1.
A single-pole switch on the active of the receiver input of remote
control must also be included in the wiring, and located the same
room as the ceiling fan.
5. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection
facilities. Contact your local government for information regarding the collection systems available. If
electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the
ground water and get into the food chain, damaging your health and well-being.
6. The structure to which the fan is to be mounted must be capable of supporting a weight of 30kg.
7. The fan should be mounted so that the blades are at least 2.3 m above the floor in Europe or 2.1 m
above the floor in Australia.
8. This fan is suitable for indoor, alfresco and coastal areas where the fan is fully undercover with a
minimum of 1 wall. This fan is not waterproof. When installed in an alfresco or coastal area, the
ceiling fan must be positioned in a location protected from water, wind and dust. Exposure to these
elements will void the warranty. Mounting the fan in a situation where it is subject to water or
moisture is dangerous and may increase the risk of damage, injury or electrical shock and will void
the warranty.
9. Must be assembled and installed by a licensed electrician.
10. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the
ceiling fan and contact the manufacturer, its service agent or suitably qualified persons.
11. The replacement of parts of the safety suspension system device shall be performed by the
manufacturer, its service agent or suitably qualified persons.
12. The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a
sufficient strength to withstand 4 times the weight of the ceiling fan; that the mounting of the
suspension system shall be performed by the manufacturer, its service agent or suitably qualified
persons.

Aria CTC Installation Instructions
3 | P a g e
PARTS LIST
•Unpack your ceiling fan carefully. Remove all parts and hardware.
•Lay out all the components on a smooth surface and make sure there are no components missing
before assembling. If parts are missing, return the complete product to the place of purchase for
inspection or replacement.
•Check whether the ceiling fan has been damaged during transport. Do not operate/install any
product which appears damaged in any way. Return the complete product to the place of purchase
for inspection, repair or replacement.
•Examine all parts, you should have the following:
Fan without light
Fan with light
1
Mounting bracket x 1
1
Mounting bracket x 1
2
Motor assembly x 1
2
Motor assembly x 1
3
Blades x 4
3
Blades x 4
4
Bottom motor cover x 1
4
LED light kit x 1
5
Motor housing x 1
5
Motor housing x 1
6
Mounting screws x 4
6
Mounting screws x 4
7
Spare screw for fan blade x 1
7
Spare screw for fan blade x 1
8
Balancing kit x 1 set
8
Balancing kit x 1 set
9
Wall switch x 1 set
9
Wall switch x 1 set
Fig. 1

Aria CTC Installation Instructions
4 | P a g e
INSTALLING THE MOUNTING BRACKET
•The ceiling fan must be installed in a location so that the blades are spaced 300mm from the tip of the
blade to the nearest objects or walls.
•Install the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least
20kg, with the 4 long screws provided. Ensure at least 30mm of the screw is threaded into the support.
(Fig. 2)
NOTE: The bracket screws provided are for use with wooden structures only. For structures
other than wood, the appropriate screw type MUST be used. Ensure the screws used are suitable
for the mounting surface and the surrounding environment.
ANGLED CEILING INSTALLATION
This fan hanging system DOES NOT support a degree angled ceiling installation.
HANGING THE FAN TO MOTOR ASSEMBLY
•Install the motor housing (1) onto the motor assembly. (Fig.3)
•Lift the fan assembly up to the mounting bracket. Hang the fan assembly onto the J-hook (2) of the
mounting bracket. (Fig.4)
•Complete the electrical wiring according to the ‘ELECTRICAL WIRING DIAGRAM’section below.
Fig. 3
Fig. 2
20 KG
Fig. 4

Aria CTC Installation Instructions
5 | P a g e
ELECTRICAL WIRING DIAGRAM
WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A
LICENSED ELECTRICIAN.
NOTE: AN ADDITIONAL ALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED
WIRING.
NOTE: Wiring diagram includes the light kit wiring. The light wiring diagram and switch is
omitted when no light kit is used with the ceiling fan.
USE WITH WALL SWITCH WIRING DIAGRAM:
Ensure the motor earth wire is connected to the single earthing terminal block “2” in the diagram below.
(Fig. 5)
Fig. 5

Aria CTC Installation Instructions
6 | P a g e
USE WITH REMOTE WIRING DIAGRAM: (REMOTE sold separately)
Ensure the motor earth wire is connected to the single earthing terminal block “2” in the diagram (Fig. 5)
for (Fig.6 and Fig.7)
1/ Remote without plugs (manual wiring)
2/ Remote with plugs (using quick connectors)
Fig. 6
Fig. 7

Aria CTC Installation Instructions
7 | P a g e
INSTALL THE FAN ASSEMBLY TO THE MOUNTING BRACKET
•After completing the electrical connection at the mounting bracket terminal block, connect the ceiling
fan wiring via the quick connector plug.
•Ensure the earth wiring is secure and correct, by performing an earthing continuity test from the
fan’s accessible metal body back to the earth terminal at the terminal block on the mounting bracket.
Install the fan assembly to the mounting bracket (Fig.8):
•Loosen two canopy screws (1) and remove from the mounting bracket.
•Loosen two canopy screws with star washer (2) by half thread from the mounting bracket. (For
L-shape slot on canopy to be mounted).
•Lift the hanging canopy of the fan assembly up to the mounting bracket and let the L-shape slot on
the hanging canopy go through the two canopy screws with star washer (2).
•Turn the hanging canopy until it locks in place at the end section of the L-shape slot, ensure the star
washer are between the hanging canopy (3) and screw head. Secure it by tightening the two canopy
screws with star washer (2).
•Secure and tighten the canopy screws (1) to the mounting bracket. The hanging canopy (3) shall
have 4 screws (1) & (2) in total. Avoid damaging the electrical wiring prepared previously when
hanging the canopy.
•Finally attach the canopy cover (4) to the mounting bracket, secure it by pushing the hooks of the
canopy cover into the slot holes of the hanging canopy and turn it anti clockwise.
Fig. 8

Aria CTC Installation Instructions
8 | P a g e
INSTALLING THE FAN BLADE AND LIGHT KIT
BLADE ATTACHMENT (Fig.9)
1. Before installing the blades, remove the blade screws and flat washers from the bottom of fan
motor.
2. Align the 2 holes on the blade with the 2 holes on the rotating member of fan motor assembly and
using the 2 blade screws in step 1, to secure the blade to the fan motor assembly.
Ensure all screws are tightened evenly to reduce the chance of warping or unbalancing. Take care
not to over tighten the screws, as this can damage the blades.
3. Once completed, repeat the process on the remaining blades.
INSTALLING THE BOTTOM COVER (FOR FAN WITHOUT LIGHT FIG.10)
Secure the bottom motor cover to the fan by turning it clockwise.
INSTALLING THE LED LIGHT KIT (FOR FAN WITH LIGHT FIG.11)
- Attach the LED light kit to the lamp base and connect wires to the LED light kit via the quick
connectors.
- Secure the LED light kit on the lamp base by turning the LED light kit body clockwise. Take care not
to cross thread or twist and damage the wires.
Fig. 10
Fig. 11
Fig. 9

Aria CTC Installation Instructions
9 | P a g e
USING YOUR CEILING FAN
FAN WALL CONTROL
Turn on the power and check the operation of the fan.
• OFF Position – Fan off
• 3rd Position – Low fan speed
• 2nd Position – Medium fan speed
• 1st Position – High fan speed
LIGHT CONTROL
• Toggle Switch – On/off
The LED Light Kit has a 3-step dimmable function which is controlled by an ON/OFF switch. Toggle the
switch ON/OFF to the luminaire 4 times within 5 seconds, the globe will light up in the following order:
100% brightness → 60% brightness → 10% brightness → 100% brightness
To switch back to 100% brightness at any stage, turn OFF the luminaire, and then after 5 seconds turn
ON the luminaire, it will reset to 100% brightness.
REVERSING SWITCH
Your ceiling fan can operate in either summer or winter mode.
SUMMER Mode: The reverse switch shall be in the SUMMER position to make the fan rotate in an
anticlockwise direction. The airflow will be directed downwards, for cooling in summer.
WINTER Mode: The reverse switch shall be in the WINTER position to make the fan rotate in a
clockwise direction. The airflow will be directed upwards assisting in the circulation of warm air, for
energy conservation in winter.
Fig. 13
Fig. 12