Lumascape Quadralux Q2 LS9140 User manual

INSTALLATION INSTRUCTIONS
ARCHITECTURAL SPOTLIGHT
FACADE LUMINAIRE
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
Products and specifications are subject to change without notice.
USA I Australia I Asia I Middle East I Europe
1 / 3
IN0168US N180410
Quadralux Q2 LS9120
Quadralux Q4 LS9140
READ ALL SAFETY INSTRUCTIONS FIRST
› Follow instructions carefully, failure to do so will void
warranty.
› Ensure installation complies with local law and
applicable standards.
› Input voltage is 120-277 V AC, 50/60 Hz
› Only use Lumascape power supply, control equipment
and leader cables.
› Ensure mains input power is surge protected.
› Never make connections whilst the power is connected.
› Do not make modifications or alter the product.
› Keep luminaire and connections clean and free of debris
and moisture.
› It is the installers responsibility that the installation is
adequately sealed to avoid moisture ingress.
LS9140
Quadralux
LS9120
Quadralux
WARNING
Install in accordance with
National Electric Code, ANSI/NFPA 70 or
the Canadian Electrical Code,
Part I (CEC), CSA C22.1

INSTALLATION INSTRUCTIONS
ARCHITECTURAL SPOTLIGHT
FACADE LUMINAIRE
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
Products and specifications are subject to change without notice.
USA I Australia I Asia I Middle East I Europe
2 / 3
IN0168US N180410
Quadralux Q2 LS9120
Quadralux Q4 LS9140
LABEL
Wiring Details
CE Color Code UL / ETL Color Code Designation
Green / Yellow Green Earth / Ground
Brown Black Active / Live
Blue White Neutral
Black Grey Data *
* Data wire must be appropriately insulated if not connected.
Operating voltage on this wire is 24 V. Incorrect wiring will
damage luminaire and void warranty. Do not Hi-Pot test.
L
N
Luminaire Cable
Connect to PowerSync™ Master or suitable power
supply in accordance with local wiring rules.
Allen Key
Use Allen key to
lock luminaire tilt
into position after
adjusting tilt.
45°
7mm
(0.25"
)
Ø15mm
(0.6")
Base View of
Mounting Bracket
Washer Plate
Use washer plate when
attaching the mounting
bracket to an accessory
or when mounting to any
mounting surface using a
countersunk screw.
Mounting Bracket
Use to attach luminaire to
suitable mounting surface.
Note that mounting bracket
can be flipped upside down
if required for installation
purposes. Do not use mounting
bracket with countersunk
screws unless using in
conjunction with washer plate.
Bracket
Mounting
Screw
Use screw to
attach luminaire to
mounting bracket.
Attach Safety Cable
See over for details.
Bootlace ferrules must be ued on all wires
when connecting in terminal blocks.

INSTALLATION INSTRUCTIONS
ARCHITECTURAL SPOTLIGHT
FACADE LUMINAIRE
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
Products and specifications are subject to change without notice.
USA I Australia I Asia I Middle East I Europe
3 / 3
IN0168US N180410
Quadralux Q2 LS9120
Quadralux Q4 LS9140
Safety Cable Attachment
Cable Anchor
Remove the little rubber plugs and screw the
safety cable attachment bracket to the luminaire.
Mounting Screws
Be sure to use spring washers provided
(between screw head and safety anchor) to
ensure screws don’t loosen over time.
Attach Safety Cable
Attach the safety cable to the bracket.
Minimum break load for cable must be ≥1,020 kg
Attach Safety Cable
Attach the other end of the safety cable to a
structural component in a suitable manner.
QUESTIONS Contact us at details below.