Luxli SFT-50R User manual

Light as soft as a cloud.
As part of Luxli’s Softi series, the LED Ring Light with Camera Mount
provides soft,attering light without harsh shadows. Control the intensity
when illuminating your subject with a variable dimmer and dial in the
right amount of light for a proper exposure.The 4.7"(11.9 cm) diameter
opening accommodates most lenses and places them at the center
of the wraparound light, which is ideal for macro or portrait work.A
bracket allows you to attach your lens and camera combos and
offers vertical adjustment for a proper t, while a macro slider helps
to ne-tune your camera position to prevent and reduce light ares.
This LED Ring Light emits a 5600 K color temperature or 3200 K with an
optional tungsten lter. And the unit can be powered by a standard
power outlet or up to two rechargeable batteries, making it a exible
choice for photographers and videographers alike.

Specications
Light source 441 LEDs
Color temperature 3200 K (with tungsten lter) or 5600 K
Brightness 11,000 lx per 19.7"(50 cm)
Power Source AC power (with included adapter)
or two Sony L-Series batteries
Continuous operating time Up to 150 min.
Battery charging time Up to 5 hr.
Output power 24.66 W
Voltage 7.4 to 14.8 V DC
Maximum lens diameter 4.7"(119 mm)
Ring light diameter 9"(23 cm)
Ring light dimensions (W × D × H) 11"× 9.8"× 2.2"(27.9 × 25 × 5.5 cm)
Weight (ring light and macro slider) 2.9 lb. (1.3 kg)

Precautions
• Do not attempt to disassemble, repair,or perform any unauthorized
modications on this device.
• Do not handle with wet hands, immerse in liquids, or expose to
water and rain. Electric shock or re may result.
• This device contains small parts which may pose a choking hazard.
Keep out of reach of children.
• Do not operate this device in the presence of ammable gas or
vapor.
• Do not use this product if it emits smoke or a strange odor.
Disconnect the power source immediately to avoid personal injury,
and contact the place of purchase.
• Observe caution when handling batteries; use only batteries
approved by the manufacturer of this product.
• Do not stare or gaze at the LED panel for prolonged periods while
the device is on.

• Batteries are prone to leakage when fully discharged.To avoid
damaging this product,be sure to remove batteries when leaving
the product unattended.
• Do not cover the ventilation grille found at the rear of the device
when in operation, and ensure the light is cool before storing.
• Do not use or leave this device in conditions of extreme heat, severe
cold, or high humidity.
• The unit will display a decrease in brightness when the battery runs
low. Be sure to replace the battery when necessary.
• Dispose of used batteries,packing, and old devices in accordance
with appropriate environmental regulations.
• All images are for illustrative purposes only.

Overview
Front
1. Battery release button
2. Battery mounts
3. Magnetic posts
4. Handle
Back
5. Power LED indicator
6. Power switch
7. Battery test button
8. Battery power indicator
9. Dimmer
10.Threaded sockets
11.Bracket locking knobs
12.DC power input
3 4 765 8 10 119
2 21 1
12

Macro Slider Top
1. 1/4"-20 camera mount
2. Macro slider guide
3. Macro slider mounting
bracket
Also Included
• Diffuser
• Tungsten lter
• Filter magnets
• 2 × NP-F750 rechargeable
batteries
• Dual battery charger
Macro Slider Bottom
4. Camera locking wheel
5. Macro slider adjustment knob
6. 1/4"-20 threaded tripod
mounts
7. Macro slider locking knob
• Battery charger power
adapter
• SFT-50R power adapter
• Power cord
• Padded carrying case
31 2 5 64
7

Powering the Ring Light
Using the AC Power Adapter
1. Plug the 3-pronged end of
the power cord into a power
source.
2. Connect the other end of
the power cord into the AC
adapter.
3. Plug the AC adapter into the
LED ring light’s DC power input.
Mounting Batteries
1. Place each battery in the
battery tray, aligning the
conductor contacts of the
battery with the metal prongs
of the light unit.
2. Lock it in place by sliding the
battery until it clicks.
3. To remove a battery,press the
corresponding battery release
button.

Checking the Battery Power
While the device is powered on,
hold the battery test button to see
how much power is remaining.
Charging the Batteries
1. Plug one end of the battery
charger’s power adapter into
a power source,and the other
end into the dual battery
charger.
2. Place each battery in a
battery tray, aligning the
conductor contacts of the
battery with the metal prongs
of the battery charger.An LED
indicator will blink to show the
battery charging progress.

Setting up the Ring Light
Mounting the Macro Slider
There are two 1/4"-20 threaded
sockets to mount the macro slider
to a tripod. One is for horizontal
orientation.The other is for portrait
orientation.
1. Align the 1/4"-20 threaded
socket with your tripod’s
mounting stud.
2. Use the tripod’s locking
mechanism to secure the
macro slider.
Mounting the Ring Light
1. Align the macro slider’s
mounting bracket with the
threaded sockets on the back
of the ring light.
2. Use the locking knobs to
secure the bracket.