M-LOCKS EM3020 User manual

Motor lock
EM2520
EM3020
EM3050
M•LOCKS BV
Vlijtstraat 40 • 7005 BN Doetinchem • The Netherlands • www.m-locks.com
Mounting
instructions
V01 EN

2www.m-locks.com
EM2520 / EM3020 / EM3050

3www.m-locks.com
Motor lock V01 EN
1 IMPORTANT INSTRUCTIONS
• Before mounting the lock, please read the instructions for use carefully.
• Ensure that you only program the lock when the safe is open.
After changing the code, always try the code several times with the safe door open.
• Only after several positive function tests (opening / closing) the safe door can be closed.
• Each key entry is confirmed by an audible tone and visual signal. These signals are not referred to in
the description that follows.
• You have a maximum of 10 seconds for each key entry. If you do not make an entry via the keypad
during this period of 10 seconds, the entry procedure will automatically abort. You must then start
again from the beginning.
• After entering a valid code, you will hear two audible tones. An invalid entry will trigger a long tone.
• If you accidentally enter an invalid code at the first attempt, you must wait 20 seconds before you
re-enter the code.
!Caution!
• The lock has been designed for use in a temperature range from +10˚C to +50˚C and a non-
condensing humidity range from 30% to 80%.
• It may only be cleaned with a moist cloth (do not use aggressive cleaning agents).
• The lock may only be installed by qualified fitters.
• The lock may not be lubricated.
• Never open the lock housing. If it is necessary to disassemble the hardware, only do so in
accordance with the technical instructions. If you fail to do so, the lock may no longer function
properly and you will forfeit your right to warranty.
2CHARACTERISTICS
The Motor lock electronic features a 6-digit manager code. The code can be changed by the manager.
With the manager code user codes can be activated and deleted. The EM3050 has a 6- or 7 digits
manager code. Depending on the programming of the lock until 9 users can be added. The lock can be
programmed with silent alarm.
EM2520 / EM3050: After entering a right code, you will hear a double tone, you can now unlock the
door and open it. If the door is not opened within 3 seconds, the lock will automatically lock again.
EM3020: After entering a right code, you will hear a double tone, you can now unlock the door and
open it. To close the lock you have to push a random key (PTC= Push To Close).
The Motor lock can be mounted in all four mounting directions. The mounting dimensions are
standard. The lock is delivered with metric (M6) mounting screws.

4www.m-locks.com
3 GENERAL
The VdS recognition of this lock is based on this mounting instruction. Read carefully.
The force applied to the lock bolt should not exceed 1 KN. If higher force is applied, please consult with
the testing institute (i.e. UL, VdS). Only use supplied screws to mount the lock. Fix the lock handtied.
The maximum allowed cable /spindle-hole diameter is 11mm (if located under the lock body).
Position of the cable hole depends on which entry unit is used.
The lock has to be fitted exclusively on steel secure storage. The mounting base also must be made of
steel. Installation on other materials only after consultation M-LOCKS or VdS .
It is recommended to prevent access to unauthorized persons to safety-relevant parts of the high-
security lock when the safe is open. Par example by a with a screws fixed interior cover.
The lock housing must be protected against destructive attacks from outside with suitable protective
materials.

5www.m-locks.com
Motor lock V01 EN
4 BOLT REQUIREMENTS AND LOCK MOUNTING
The force applied to the lock bolt in locked condition must not exceed 1 KN (p. E. by a preconceived
breaking point). If higher force is desired please consult with the manufacturer. Only use supplied
screws to mount the lock. Handtighten the screws securely so the lock body is attached firmly to the
mounting surface.
In the LOCKED position, there should be approximately 1 mm clearance
between the lock bolt and the cavity in the blocking bar of the bolt-
work. The lock bolt must move freely into the cavity.
Any bolt attachment should not exceed 0.5 Kg / 1 lb.
(equals a force of 5N)
When the lock bolt is retracted, the distance to the blocking bar must
not exceed 5 mm.
5 MOUNTING INSTRUCTIONS
Insert the connector of the entry unit in the inner position. Check that the connector(s) is completely
seated. To remove the connector(s), carefully lift and pull it out. In the entry unit or battery / alarmbox
connect a 9V ALKALINE Duracell, Industrial or Energizer batteries. Tie cables away from moving parts.
Note:
If a cable /spindle hole is located under the Motor lock, use a suitable drill protection; part number
T016.
Cable-hole 9-12 mm.

6www.m-locks.com
6 FUNCTIONAL TEST
Functional tests alway with door open!
• Enter code (1,2,3,4,5,6 or 5,5,5,5,5,5).
• Turn boltwork handle towards ‘OPEN’ position.
• For EM2520: After approximately 5 seconds, the motor can be heard again when it pushes the lock
bolt against the blocking bar of the boltwork.
• Turn handle towards ‘LOCKED’ position.
• For EM3020: Push a random key. You can hear the motor and the bolt will slide to the locked
position.
• When the lock is closed you will hear a double signal.
Repeat functional test several times before locking the safe door!
Check the keypad
If the lock does not react, follow the procedure below to check that your keypad is working.
Press and hold key ‘5’ until you hear a double tone. The LED will illuminate when performing the fol-
lowing actions:
5
Next, press all of the keys one by one and one after the other.
1234567890
If the key = OK
If the key = not OK , the test will be aborted.
If one or more keys do not operate properly, please contact your supplier.

7www.m-locks.com
Motor lock V01 EN
7 DATA SHEET
EM2520 / EM3020 /
EM2520 S / EM3020 S
EM3050 / EM3050 S EM3050 AB
Opening Automatic Automatc Automatic
Locking Automatic / PTC Automatic / PTC Automatic / PTC
Blocking element Blocking gear / Motor Blocking gear / Motor Blocking gear / Motor
Mounting Dimensions Standard Standard Standard
Possible mounting positions 4 4 4
EM2520 / EM3020 /
EM2520 S / EM3020/S
EM3050 / EM3050 S EM3050 AB
Power supply 9V Alkaline Duracell, Industrial or Energizer Battery
Software
Codes 2 (6 digits) Up to 10 (6 or 7 digits) Up to 10 (6 or 7 digits)
Manager Codes 1 1 1
User Codes 1 Up to 9 Up to 9
Time delay / open window 01-99 min / 01-19 min 01-99 min / 1-19 min 01-99 min / 1-19 min
Battery low signal Yes Yes Yes
Dallas key - Dallas key and code Dallas key and code
Silent alarm - Silent alarm Silent alarm
Audit 2000 events with
Date & Time - - With AB3000
Manipulation protection 5 minute lockout after 4 consecutive wrong codes
8 NOTES
2015_V01_EN Errors and modifications reserved

M•LOCKS BV
Vlijtstraat 40 • 7005 BN Doetinchem • The Netherlands • www.m-locks.com