M-LOCKS Tantum Basic User manual

Made in The Netherlands
Tantum
Basic / MLS
Mounting
instructions
V02 EN

2www.m-locks.com
TANTUM BASIC / TANTUM MLS
1 IMPORTANT INSTRUCTIONS
• Before mounting the lock, please read the instructions for use carefully.
• Ensure that you only program the lock when the safe is open.
After changing the code, always try the code several times with the safe door open.
• Only after several positive function tests (opening / closing) the safe door can be closed.
• Each key entry is confirmed by an audible tone and visual signal. These signals are not referred to in
the description that follows.
• You have a maximum of 10 seconds for each key entry. If you do not make an entry via the keypad
during this period of 10 seconds, the entry procedure will automatically abort. You then have to
start from the beginning.
• After entering a valid code, you will hear two audible tones. An invalid entry will trigger a long tone.
• If you accidentally enter an invalid code at the first attempt, you must wait 20 seconds before you
re-enter the code.
• Our products fulfil the EN1300 requirements regarding resistance against electrostatic charge.
In fact it may happen that the electrostatic charge of a user exceeds the extreme value many times.
That’s why we are asking you to touch the metal surface of the safe for discharging before
operating the lock.
!The certifications of our locks are valid only if used together with the entry units indicated on the
respective certificates. As soon as an entry unit not specified on our certificates is used, the certifica-
tion of the lock expires immediately.

3www.m-locks.com
Tantum V02 EN
!Caution!
• The lock has been designed for use in a temperature range from +10˚C to +50˚C and a non-
condensing humidity range from 30% to 80%.
• It may only be cleaned with a moist cloth (do not use aggressive cleaning agents).
• The lock may only be installed by qualified fitters.
• The lock may not be lubricated.
• Never open the lock housing. If it is necessary to disassemble the hardware, only do so in
accordance with the technical instructions. If you fail to do so, the lock may no longer function
properly and you will forfeit your right to warranty.
2CHARACTERISTICS
The motor lock can be mounted in all four mounting directions. The mounting dimensions are
standard. The lock is delivered with metric (M6) mounting screws.
The electronics feature a 6-digit main code (in some cases it may be that the lock requires a 7-digit
code) that can be changed by the user. With the main code user code(s) can be activated and deleted.
After entering a valid code, a double signal sounds and the motor will retract the lock bolt. You can
now open the door/bolt work. Closing the lock can either be done automatically by closing the door/
bolt work (Automatic Closing) or by pushing a random digit on the keypad (Push to Close). The default
closing mode is Push to Close. The main code can change the closing mode to Automatic closing. To
achieve “Automatic Closing” it is imperative that a door-/bolt work switch (NC=Normally Closed) is
connected to the lock.
If the door is not opened within 5 seconds, the lock will automatically lock again in case “Automatic
Closing” is active.
A signal will sound every 10 seconds as long as the lock is open in case “Push to Close” is active.
Three long tones will sound when during opening or closing the lock bolt is blocked. Entering the code
again will close, respectively open the lock again. Remove the obstruction and retry.

4www.m-locks.com
3 GENERAL INSTRUCTIONS
The certification of this lock is based on this mounting instruction. Read carefully.
The force applied to the lock bolt should not exceed 1 kN. If higher force is applied, please consult with
the manufacturer / certificate holder (M-LOCKS). Only use supplied screws (M6) to mount the lock.
Tightening torque 4,5 Nm.
The position of the cable entry depends on the input unit used. The Tantum motor lock is available with
and without drill protection. When installing the lock behind a cable feed-through / opening always the
lock with the factory anti-drilling protection (Tantum anti drill) must be used.
Attention! The certification of the lock types ‘Tantum anti drill’ is only valid with the drill protection
applied at the factory. The standard dimensions are 30x45x1.5 (LxWxH, in mm). The lock loses its
certification if you retrofit the drill protection yourself. Depending on the area of application,
construction and resistance class of your secure storage unit, it may be possible that you need a
stronger drilling protection or that the lock shall be protected by other constructive measures to
achieve the required resistance class.
A lock without drilling protection shall not be installed behind an existing cable guide / opening.
The maximum size of the cable / spindle-hole must not exceed a diameter (Ø) of 15 mm or the
contour of the key hole shown below.
The lock has to be fitted exclusively on a steel secure storage. The mounting base also must be made
of steel. Installation on other materials only after consultation with M-LOCKS or certification institute.
66,7 mm
41,2 mm 60,3 mm
9,3 mm
85,2 mm
12,5 mm
25,4 mm
12 mm throw
26,75 mm
12,5 mm
9,6
23,5
6
A A
B B
C C
D D
E E
F F
4
4
3
3
2
2
1
1
DRAWN
CHK'D
APPV'D
MFG
Q.A
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
FINISH:
DEBURR AND
BREAK SHARP
EDGES
NAME
SIGNATURE
DATE
MATERIAL:
DO NOT SCALE DRAWING
REVISION
TITLE:
DWG NO.
SCALE:2:1 SHEET 1 OF 1
A4
WEIGHT:
Schlusselführung

5www.m-locks.com
Tantum V02 EN
It is recommended to prevent access to unauthorized persons to safety-relevant parts of the high-
security lock when the safe is open. For instance by a with screws fixed interior cover.
The lock housing must be protected against destructive attacks from outside with suitable protective
materials .
4 BOLTWORK REQUIREMENTS
The force applied to the bolt work on the lock bolt has to be limited to 1 kN (E.g. by a preconceived
breaking point). Please contact your manufacturer if higher forces are needed. Only use supplied
screws to mount the lock.
In the LOCKED position the distance between the bolt and the bolt
work should be approximately 1 mm.
Check on the boltwork handle to see if the lock is locked.
5 MOUNTING INSTRUCTIONS
Mount the entry unit following the manufacturer’s instruction.
1. Battery- or Alarm box
2. Keypad cable
3. Door/bolt work switch (NC)
Insert the connector of the entry unit in in position 2 and check that the connector is completely
seated.
312

6www.m-locks.com
Connect a 9V alkaline Procell, Duracell , Energizer or Duracell Industrial battery to the battery clip to the
keyboard (or battery box) , and check the lock functions .
Please lay the cables in such a way that they are not kinked, that the cables are not crushed and that
there is no friction with moving parts of the boltwork.
When installing the cable, make sure that the connecting cable has enough space between the lock and
moving parts. We recommend a distance of at least 5 mm and a fixation of the connecting cables e.g.
by means of cable ties.
If the distance between the cable and the lock is too small, the manufacturer (M-LOCKS) can provide
you with special M6 spacer bolts (increase the distance by 6 mm) or longer M6 / polyamide-coated
fastening screws.
When using longer fastening screws, it is possible to independently increase the distance (lock / bolt-
work) using metal spacer washers / bushings.
In this case, please ensure that the fastening screws still have sufficient engagement with the fasten-
ing points of the boltwork.
6 FUNCTIONAL TEST
As with all locks from M-LOCKS, this unit has a unique feature for checking the electronics (both that
of the input unit and that of the lock): ’Function 5’.
Press and hold key ‘5’ until you hear a double tone. The LED will illuminate when performing the
following actions:
5
Next, press all of the keys in one by one and one after the other.
1234567890
If the key = OK
If the key = not OK , the test will be aborted.
If one or more keys do not operate properly, please contact your supplier.
Perform this functional test always with door open!
Functional test
• Enter code. The lock emits a double signal for the correct code.
• When the lock bolt is fully retracted turn bolt work handle towards OPEN position.
• Turn handle towards LOCKED position.
• In case the lock is programmed with Push to Close, push a random digit on the keypad. The lock
should close now.
• In case the lock is programmed to close automatically the lock should close as soon as the bolt work
is in the fully closed position (signalled by a door/ bolt work switch).
• Make sure there is an air space on all sides of the lock bolt when the safe’s bolt work is fully thrown
into locked position.

7www.m-locks.com
Tantum V02 EN
Installation check
With door open, bring bolt work in LOCKED position:
• Avoid continuous pressure on the lock bolt.
• During the movement of the bolt work the cables should be clear of moving parts.
Only after several positive function tests (opening / closing) the safe door can be closed!
7 DATASHEET
8 NOTES
2021_V02_EN Errors and modifications reserved
Tantum Basic /
Tantum Basic anti drill
Tantum MLS
Tantum MLS anti drill
Opening Automatic Automatic
Locking Automatic / Push to Close Automatic / Push to Close
Blocking element Motor Motor
Mounting dimensions Standard Standard
Possible mounting positions 4 4
Tantum Basic /
Tantum Basic anti drill
Tantum MLS /
Tantum MLS anti drill
Power supply 9V Alkaline Duracell, Procell or Energizer block batteries
Software
Codes 2 (6 digits) Up to 10 (6 or 7 digits)
Manager Codes 1 1
User Codes 1 Up to 9
Time delay / open window 01-99 min / 01–19 min 01-99 min / 1-19 min
Battery low signal Yes Yes
Volume adjustable Yes Yes
Silent alarm Yes Yes
Dual mode - Yes
Audit 200 events - Yes
Manipulation protection 5 minute lockout after 4 consecutive wrong codes

M-LOCKS BV
Vlijtstraat 40
7005 BN Doetinchem
The Netherlands
If you need some help, please send an E-mail to:
[email protected]
We will be happy to help you!