M-system R6-NE1 User manual

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-7787 Rev.7 P. 1 / 9
INSTRUCTION MANUAL
ETHERNET INTERFACE MODULE
(Modbus/TCP, for 32-point analog signals) MODEL R6-NE1
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
Network interface module ..................................................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
• The equipment must be mounted inside a panel.
• Install lightning surge protectors for those wires connect-
ed to remote locations.
• Insert a noise filter for the communication line connected
to the unit. NEC TOKIN Model ESD-SR-250 or equiva-
lent is recommended.
• The actual installation environments such as panel con-
figurations, connected devices, connected wires, may af-
fect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure the CE conform-
ity.
■HOT INSERTION/REMOVAL OF MODULES
• It is possible to replace the module with the power is sup-
plied. Be sure to replace it when the module is not com-
municating with a host, as it is possible to affect the sys-
tem. However, replacing multiple modules at once may
greatly change line voltage levels. We recommend that
you replace them one by one.
■GENERAL PRECAUTIONS
• Do not set the DIP switch on the side panel while the
power is supplied. The DIP switch is selectable for main-
tenance without the power.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.

R6-NE1
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-7787 Rev.7 P. 2 / 9
INSTALLATION
Use the Base Model R6x-BSA or B6x-BSB.
Before mounting the Network Interface Module onto the Base, be sure to configure the module as explained below.
■DATA ALLOCATION
The setting determines the data area size assigned to each
I/O module mounted on the base.
The data sent/received via Modbus is mapped according to
this setting.
In order to use the second channel of analog I/O modules,
choose the Mode 2. (The 2nd channel cannot be sent/re-
ceived in the Mode 1.)
See “COMPONENT IDENTIFICATION.”
■NETWORK SLOTS ON THE BASE
Mount the Network Module to the dedicated slot on the
base.
• R6x-BSA
The I/O and the power (model: R6x-PF1) modules can be
positioned freely on whichever among the slots 1 through 8.
Set a module address to each I/O module.
123 ・・・ 8
Network
Module
I/O & Power Supply
Modules
• R6x-BSB
The power module (model: R6-PSM) should be located on
the extreme left, the I/O modules can be positioned freely
on whichever among the slots 1 through 8. Set a module
address to each I/O module.
1
Power Supply
Module
I/O Modules
23 ・・・8
Network
Module

R6-NE1
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-7787 Rev.7 P. 3 / 9
COMPONENT IDENTIFICATION
RUN Indicator LED
ERR Indicator LED
Configuration Jack
RJ-45 Connector
■ SIDE VIEW ■ FRONT VIEW
ON
12345678
LED Function Data Allocation
LINK
DPLX (Duplex)
COLL (Collision)
LINK10 (10Mbps)
LINK100
(100Mbps)
Ethernet LED
Not used
Not used
8
6
7
3
4
5
2
1
0
F
E
D
C
B
A
9
8
6
7
3
4
5
2
1
0
F
E
D
C
B
A
9
■SIDE DIP SW
(*) Factory setting
• Data Allocation Mode: SW1, SW2
DATA ALLOCATION MODE SW1 SW2
1■
2 (*)
= ON, Blank = OFF
• LED Function: SW3
LED FUNCTION SW3
RUN:
ERR:
Green ON in normal communications
(*)
Green ON/blinks in an abnormality
RUN:
ERR:
Red ON when receiving
Red ON when transmitting ■
= ON, Blank = OFF
Note: Be sure to set unused SW4 through 8 to OFF.
■ETHERNET INDICATORS
ID COLOR FUNCTION
LINK Red ON at LINK
DPLX Red ON with full-duplex communication
LINK10 Red ON with 10 Mbps connection
LINK100 Red ON with 100 Mbps connection
COL Red Blinking when collision occurs
PC CONFIGURATOR
With configurator software, settings shown below are available.
Refer to the software manual of R6CON for detailed operation.
■INTERFACE MODULE SETTING
PARAMETER AVAILABLE RANGE DEFAULT SETTING
Communication Failure Detection Time 0.2 – 3200.0 (sec.) 3.0 (sec.)
IP address 255.255.255.255 192.168.0.1
Port 1 0 – 32767 502
Port 2 0 – 32767 502
Port 3 0 – 32767 502
Port 4 0 – 32767 502
TCP connection close time 1 1.0 – 3200.0 (sec.) 180.0 (sec.)
TCP connection close time 2 1.0 – 3200.0 (sec.) 180.0 (sec.)
TCP connection close time 3 1.0 – 3200.0 (sec.) 180.0 (sec.)
TCP connection close time 4 1.0 – 3200.0 (sec.) 180.0 (sec.)
Card map 00000000 to FFFFFFFF FFFFFFFF

R6-NE1
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-7787 Rev.7 P. 4 / 9
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
■EXTERNAL DIMENSIONS unit: mm (inch)
90 (3.54) 5.6
(.22)
90 (3.54) LOCKING CLAMP
POSITIONING GUIDE
18 (.71)
■CONNECTION DIAGRAM
INTERNAL POWER
INTERNAL BUS
CONFIGURATION
JACK
JACK
BUS CONNECTOR
Modbus/TCP RJ-45
CONNECTOR

R6-NE1
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-7787 Rev.7 P. 5 / 9
CHECKING ETHERNET CONNECTION
■IP ADDRESS
The R6-NE1 does not support BootP Table Software. The IP Address and Subnet Mask can be configured using the R6CON
Configurator Software.
The Modbus/TCP Port No. is fixed at 502.
■DATA ALLOCATION MODE
The Data Allocation Mode is usually set to ‘2’ with the side DIP switches. Setting ‘1’ is used only when all the I/O modules on
the base are for Data Allocation Mode 1. This setting affects analog I/O data allocations.
■CHECK WIRING
Connect an Ethernet cable to the front RJ-45 connector.
■CHECK LED
When wiring is correct, LINK and LINK10, or LINK and LINK100 are turned on.
When the module is receiving or sending data, LINK10 or LINK100 blinks.*
* LEDs are turned ON for firmware version V2.02 or later.
■CHECK R6-NE1 CONNECTION
Enter “ping command” on the Windows MS-DOS as follows:
C:¥WINDOWS>ping ***.***.***.***
(***.***.***.***: Enter IP address in decimal.)
ping ***.***.***.*** with 32 bytes of data:
Reply from ***.***.***.*** : bytes=32 time<10ms TTL=64
Reply from ***.***.***.*** : bytes=32 time<10ms TTL=64
Reply from ***.***.***.*** : bytes=32 time<10ms TTL=64
Reply from ***.***.***.*** : bytes=32 time<10ms TTL=64
Ping statistics for ***.***.***.***
Packets:Sent=4,Received=4,Lost=0(0% loss)
Replies in case of normal connection are as shown above. If the connection cannot be established normally due to e.g. wrong
IP address, other replies such as ‘timeout’ will be received.
■CHECK CONNECTION TO THE APPLICATION SOFTWARE
Check Point 1: LINK LEDs
When normal connection is established, the front LINK and LINK10 or LINK100 are turned on regardless of data sending/
receiving status. Check power supply to the switch/hub in case that these LEDs are not on.
Check Point 2: RUN Indicator LED
With the side DIP SW3 is set to OFF, a green LED turns on at the RUN Indicator LED in normal data sending/receiving.
Check Point 3: Sending/Receiving Indicators
With the side DIP SW3 is set to ON, a red LED turns on at the RUN Indicator LED in data receiving, and a red LED turns
on at the ERR Indicator LED in data sending. In normal operating conditions, these LEDs may seem to blink at once due to
the high speed transmission.

R6-NE1
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-7787 Rev.7 P. 6 / 9
MODBUS FUNCTION CODES & SUPPORTED CODES
■Data and Control Functions
CODE NAME
01 Read Coil Status X Digital output from the slave (read/write)
02 Read Input Status X Status of digital inputs to the slave (read only)
03 Read Holding Registers X General purpose register within the slave (read/write)
04 Read Input Registers X Collected data from the field by the slave (read only)
05 Force Single Coil X Digital output from the slave (read/write)
06 Preset Single Registers X General purpose register within the slave (read/write)
07 Read Exception Status
08 Diagnostics X
09 Program 484
10 Poll 484
11 Fetch Comm. Event Counter Fetch a status word and an event counter
12 Fetch Comm. Event Log A status word, an event counter, a message count and
a field of event bytes
13 Program Controller
14 Poll Controller
15 Force Multiple Coils X Digital output from the slave (read/write)
16 Preset Multiple Registers X General purpose register within the slave (read/write)
17 Report Slave ID
18 Program 884 / M84
19 Reset Comm. Link
20 Read General Reference
21 Write General Reference
22 Mask Write 4X Register
23 Read / Write 4X Registers
24 Read FIFO Queue
■Exception Codes
CODE NAME
01 Illegal Function X Function code is not allowable for the slave
02 Illegal Data Address X Address is not available within the slave
03 Illegal Data Value X Data is not valid for the function
04 Slave Device Failure
05 Acknowledge
06 Slave Device Busy
07 Negative Acknowledge
08 Memory Parity Error
■Diagnostic Subfunctions
CODE NAME
00 Return Query Data X Loop back test
01 Restart Comm. Option X Reset the slave and clear all counters
02 Return Diagnostic Register X Contents of the diagnostic data (2 bytes)
03 Change ASCII Input Delimiter X Delimiter character of ASCII message
04 Force Listen Only Mode X Force the slave into Listen Only Mode

R6-NE1
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-7787 Rev.7 P. 7 / 9
MODBUS I/O ASSIGNMENTS
The DIP SW located at the side of the module switches the unit’s data allocation mode.
In the Data Allocation Mode 1, one (1) word is assigned per module. The second channel of analog I/O modules cannot be used.
In the Data Allocation Mode 2, two (2) words are assigned per module regardless of whether the second word area is required
or not.
For discrete I/O, 16-channel area is automatically assigned to each module. With a 4-channel module, the bits assigned to ch.
5 through 16 remain “0.”
Note: DO NOT access addresses other than mentioned below. Such access may cause problems such as inadequate operation.
Coil (0X) 1 – 16 Module address 0 Do 1 – 4
17 – 32 Module address 1 Do 1 – 4
33 – 48 Module address 2 Do 1 – 4
49 – 64 Module address 3 Do 1 – 4
: : :
241 – 256 Module address 15 Do 1 – 4
Inputs (1X) 1 – 16 Module address 0 Di 1 – 4
17 – 32 Module address 1 Di 1 – 4
33 – 48 Module address 2 Di 1 – 4
49 – 64 Module address 3 Di 1 – 4
: : :
241 – 256 Module address 15 Di 1 – 4
257 – 272 Active module map
273 – 288 Status
289 – 320 Channel status
■Data Allocation Mode 1
Input Registers
(3X)
1 Module address 0 Ai 1 (INT)
2 Module address 1 Ai 1 (INT)
3 Module address 2 Ai 1 (INT)
4 Module address 3 Ai 1 (INT)
: : :
16 Module address 15 Ai 1 (INT)
17, 18 Module address 0 Ai 1 (Float)
19, 20 Module address 1 Ai 1 (Float)
21, 22 Module address 2 Ai 1 (Float)
23, 24 Module address 3 Ai 1 (Float)
: : :
47, 48 Module address 15 Ai 1 (Float)
Holding Registers
(4X)
1 Module address 0 Ao 1 (INT)
2 Module address 1 Ao 1 (INT)
3 Module address 2 Ao 1 (INT)
4 Module address 3 Ao 1 (INT)
: : :
16 Module address 15 Ao 1 (INT)
17, 18 Module address 0 Ao 1 (
Float )
19, 20 Module address 1 Ao 1 (
Float )
21, 22 Module address 2 Ao 1 (
Float )
23, 24 Module address 3 Ao 1 (
Float )
: : :
47, 48 Module address 15 Ao 1 (
Float )
■Data Allocation Mode 2
Input Registers
(3X)
1 Module address 0 Ai 1 (INT)
2 Module address 0 Ai 2 (INT)
3 Module address 1 Ai 1 (INT)
4 Module address 1 Ai 2 (INT)
: : :
31 Module address 15 Ai 1 (INT)
32 Module address 15 Ai 2 (INT)
33, 34 Module address 0 Ai 1 (Float)
35, 36 Module address 0 Ai 2 (Float)
37, 38 Module address 1 Ai 1 (Float)
39, 40 Module address 1 Ai 2 (Float)
: : :
93, 94 Module address 15 Ai 1 (Float)
95, 96 Module address 15 Ai 2 (Float)
Holding Registers
(4X)
1 Module address 0 Ao 1 (INT)
2 Module address 0 Ao 2 (INT)
3 Module address 1 Ao 1 (INT)
4 Module address 1 Ao 2 (INT)
: : :
31 Module address 15 Ao 1 (INT)
32 Module address 15 Ao 2 (INT)
33, 34 Module address 0 Ao 1 (
Float )
35, 36 Module address 0 Ao 2 (
Float )
37, 38 Module address 1 Ao 1 (
Float )
39, 40 Module address 1 Ao 2 (
Float )
: : :
93, 94 Module address 15 Ao 1 (
Float )
95, 96 Module address 15 Ao 2 (
Float )

R6-NE1
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-7787 Rev.7 P. 8 / 9
■ACTIVE MODULE MAP
Indicates the slots where I/O modules are mounted. When the module is mounted, the corresponding bit turns to “1.”
257272
Module address 0
Module address 1
Module address 2
Module address 15
■STATUS
Communication status data. When one or more I/O modules are mounted on the base, the corresponding bit turns to “0.”
273288
“0”
“0”
“0”
“0”
I/O Module Found (0 : I/O module(s) found, 1 : No I/O module found)
“0”
“0”
“0”
Internal Communication Counter
(Every Internal Communication Cycle Adds +1)
■CHANNEL STATUS
Channel Status shows the I/O module’s data error.
- Input overrange (≤ -15% or ≥ 115%) of Input modules except R6x-TSx and R6x-RSx.
- Inputs of R6x-TSx, R6x-RSx burnout.
- Output wire breakdown of R6x-YSx (Firmware Version 2.00 or later).
In the above case, the corresponded bit is “1.”
289304
Module address 0
Module address 1
Module address 2
Module address 15
305320
Unused
289304
Module address 0
Module address 1
Module address 2
Module address 7
305320
Module address 8
Module address 9
Module address 10
Module address 15
• Data Allocation Mode 1•Data Allocation Mode 2
In the Data Allocation Mode 2, the LSB is used for channel 1, and the MSB for channel 2, of an analog module.

R6-NE1
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-7787 Rev.7 P. 9 / 9
I/O DATA DESCRIPTIONS
• 16-bit Analog Data
0 to 100% of the selected I/O range is converted into 0 to 10000 (binary).
With °C temperature unit, raw data is multiplied by 10. For example, 25.5°C is converted into 255.
With °F temperature unit, the integer section of raw data is directly converted into the data. For example, 135.4°F is con-
verted into 135.
Negative values are represented in 2’s complements.
015
• Discrete Data
Input 1 (Output 1)
Input 2 (Output 2)
Input 3 (Output 3)
Input 4 (Output 4)
Not Used (Remains “0”)
0 : OFF
1 : ON
015