M-system SC100 Series User manual

1
SCCFG Users Manual EM-9192 Rev.4
SC100/SC200 Series
Multi-Function PID Controller
PC CONFIGURATOR SOFTWARE
Model: SCCFG
Users Manual
http://www.m-system.co.jp/
5-2-55, Minamitsumor
i, Nishinari-ku, Osaka 557-0063 JAPA
N
Te l: [phone] Fax: [phone]
E-mail: [e-mail]

2
SCCFG Users Manual EM-9192 Rev.4
Contents
1. INTRODUCTION ...................................................................................3
2. BEFORE GETTING STARTED .............................................................4
2.1 GENERAL DESCRIPTIONS ..............................................................................................4
2.2 SYSTEM REQUIREMENTS ...............................................................................................4
3. MAIN DIALOG.......................................................................................5
4. COMMUNICATION................................................................................6
4.1 COP-IRDA COMMUNICATION ADAPTOR.........................................................................6
4.2 SETTING ON THE CONTROLLER....................................................................................6
4.3 COP-US COMMUNICATION ADAPTOR ............................................................................6
4.4 SETTING ON THE CONTROLLER....................................................................................6
5. COM PORT SETTING...........................................................................7
6. CONFIGURATION.................................................................................8
6.1 UPLOAD FROM DEVICE ...................................................................................................8
6.2 READ CFG FILE ................................................................................................................8
6.3 DOWNLOAD TO DEVICE...................................................................................................8
6.3.1 WRITE TO DEVICE WITH DIFFERENT LCD FIRMWARE VERSION .....................9
6.4 WRITE TO CFG FILE ....................................................................................................... 10
6.5 EXPORT TO CSV ............................................................................................................. 10
6.6 CONFIGURATION DATA IN CSV FORMAT...................................................................... 11
6.7 CONFIGURATION ITEM LIST.......................................................................................... 19
7. SHORT TREND DATA .........................................................................22
7.1 UPLOAD AND EXPORT TO CSV.....................................................................................22
7.2 SHORT TREND DATA IN CSV FORMAT..........................................................................23
Appx 1. ERROR CODES..........................................................................24

3
SCCFG Users Manual EM-9192 Rev.4
1. INTRODUCTION
Thank you for choosing M-System’s SC100/200 Series Multi-Function PID Controllers.
This manual describes software functions of PC Congurator Software model: SCCFG, PC environment and opera-
tion methods. Please refer to the relevant hardware users manuals for the detailed information about the terms used
in this manual.
The SCCFG makes it easy and smooth to set parameters to the SC100/200 Series. Setting data and short trend data
can be exported to CSV le via infrared communication.
LCD rmware version mentioned in the text can be conrmed on the screen of the Controller. Go to: Conguration
view > Version > SC_LCD Ver. X.XX.

4
SCCFG Users Manual EM-9192 Rev.4
2. BEFORE GETTING STARTED
2.1 GENERAL DESCRIPTIONS
Uploading and saving setting data Conguration setting data saved in the Controller is uploaded to a PC via infrared com-
munication and saved in binary or CSV le format.
Downloading setting data Conguration setting data saved in the PC is downloaded to the Controller via infrared
communication. Only binary format le can be transferred.
Creating short trend data les*Short trend data le received from the Controller via infrared is converted into CSV and
saved.
*SC200, SC210, SC200D, SC200W and SC210W only.
2.2 SYSTEM REQUIREMENTS
PC IBM PC/AT or compatible
OS
Windows XP SP3 or later, Windows Vista, Windows 7 (32-bit / 64-bit),
Windows 10 (32-bit / 64-bit)
Note: no guarantee for all environments
Resolution 1024 by 768 pixels or higher
Display color 65000 colors (16-bit)
USB Port Used to communicate with the Controller via Communication Adaptor model: COP-IRDA
or COP-US.

5
SCCFG Users Manual EM-9192 Rev.4
3. MAIN DIALOG
Double-clicking SCCFG.exe icon starts the SCCFG to show Main Dialog as shown below.
(1) “Uploaded from device” is indicated when [Upload from device] has been successfully completed.
File name is indicated when [Read CFG le] has been successfully completed.
(2) Device Model and LCD Ver. are indicated when [Upload from device] or [Read CFG le] has been successfully
completed. (e.g. LCD Ver. : 1.0x)
(3) The buttons become selectable once [Upload from device] or [Read CFG le] is complete.
MAIN DIALOG MENU
Conguration
Upload from device Setting data is uploaded from the Controller via infrared communication.
Read CFG le Setting data is read in from a le.
Download to device Setting data is download to the Controller via infrared communication.
New setting is valid only after the power supply is restarted.
Write to CFG le Setting data is saved in a le.
Export to CSV Setting data is converted into CSV and saved.
Short trend data Upload and export to CSV
Short trend data is acquired from the device via infrared and saved as
CSV le.
Error occurs with models SC100 or SC110.
COM Port COM port for infrared communication is specied.
(1)
(2)
(3)

6
SCCFG Users Manual EM-9192 Rev.4
4. COMMUNICATION
4.1 COP-IRDA COMMUNICATION ADAPTOR
Use M-System’s Model COP-IRDA or COP-US to communicate with the Controller via infrared rays. Before using
the COP-IRDA, install its driver in your PC. Refer to the instruction manual for the COP-IRDA for more information.
When the driver is installed correctly, the COP-IRDA is assigned to a COM port.
4.2 SETTING ON THE CONTROLLER
Set only one Controller module to infrared communication mode at once when multiple devices line up side by side.
Refer to the users manual for the Controller for more information to operate the Controller to activate the communica-
tion mode.
4.3 COP-US COMMUNICATION ADAPTOR
Use M-System’s Model COP-US to communicate with the Controller with wired communication. Before using the
COP-US, install its driver in your PC. Refer to the instruction manual for the COP-US for more information.
When the driver is installed correctly, the COP-US is assigned to a COM port.
4.4 SETTING ON THE CONTROLLER
Refer to the users manual for the Controller for more information to operate the Controller to activate the communica-
tion mode.
PC
SCCFG
Controller
COP-IRDA
USB portInfrared port
Max. 0.2 m
PC
SCCFG
Controller
COP-US
USB portConfigurator jack
Connector
adapter

7
SCCFG Users Manual EM-9192 Rev.4
5. COM PORT SETTING
Select COM No. assigned to the COP-IRDA or COP-US among COM1 to COM20.

8
SCCFG Users Manual EM-9192 Rev.4
6. CONFIGURATION
6.1 UPLOAD FROM DEVICE
Click on [Upload from Device] button to call up the setting data saved in the Controller.
6.2 READ CFG FILE
Click on [Read CFG le]. The folder directory appears on the screen. Select a conguration le and click on [Open].
6.3 DOWNLOAD TO DEVICE
Click on [Download to device] button to write the setting data presently on the screen. All data except for the port
setting is downloaded.
The table below shows relevant parameters.
PARAMETER Write (X)
Back light brightness X
Screen saver (time) X
MV-0/100% symbol X
Loop display (MV, OP) X
Loop variables X
Graph scale divisions X
Decimals (% display) X
Alarm blinking X
Bargraph color X
Digital display color X
Trend recording X
Storing interval X
Trend channel X
Trend graph color X
Selected loop color X
Touch tone X
Home X
Select operation view X
Select unit mode X
Modbus-RTU No
Modbus/TCP No
Language X
Parameter setting*1X
PRG mode indicator*2X
Numerical key control*2X
*1. For Range Hi limit, Range Lo limit and Decimal place, LCD rmware version 1.5x or later
*2. LCD rmware version 1.5x or later

9
SCCFG Users Manual EM-9192 Rev.4
6.3.1 WRITE TO DEVICE WITH DIFFERENT LCD FIRMWARE VERSION
When the LCD rmware version of setting data, which is created by “READ CFG FILE” or “DOWNLOAD TO DEVICE”,
is different from the LCD rmware version of destination device, the data may change to factory setting value depend-
ing on conguration item. Except following conguration items, the data can be handed over even LCD rmware is
different.
• When reading conguration of LCD rmware version 1.3x or 1.4x and writing to the device with LCD rmware version
1.5x or later.
LCD rmware version of read data:
Ver. 1.3x (SC100, SC110, SC200, SC210)
Ver. 1.4x (SC100, SC110, SC200, SC210)
LCD rmware version of destination device:
Ver. 1.5x or later
CONFIGURATION ITEM DATA
User’s parameter table item
(Range Hi limit, Range Lo limit and Decimal place)
Factory setting*
PRG mode indicator Factory setting*
Numerical key control Factory setting*
*Refer to 6.7 CONFIGURATION ITEM LIST

10
SCCFG Users Manual EM-9192 Rev.4
6.4 WRITE TO CFG FILE
Click on [Write to CFG le]. The folder directory appears on the screen. Type the name and click on [Save].
6.5 EXPORT TO CSV
Click on [Export to CSV]. The folder directory appears on the screen. Type the name and click on [Save].