manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. M-system
  6. •
  7. Transmitter
  8. •
  9. M-system 10TG User manual

M-system 10TG User manual

BEFORE USE ....
Thank you for choosing us. Before use, please check con-
tents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact our sales office or representatives.
■PACKAGE INCLUDES:
Signal conditioner ...............................................................(1)
Mounting screw (M3.5 × 10)...............................................(2)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■POWER INPUT RATING & OPERATIONAL RANGE
• Locate the power input rating marked on the product and
confirm its operational range as indicated below:
24V DC rating: 24V ±10%,
approx. 35mA with voltage output 1
approx. 55mA with current output 1
■GENERAL PRECAUTIONS
• Before you remove the unit or mount it, turn off the power
supply and input signal for safety.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -5 to +55°C
(23 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
• Be sure to put the terminal cover on while the power is
supplied.
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
COMPONENT IDENTIFICATION
Zero Adj.
Span Adj. Output 1
Body
Specifications
Connection Diagram
(side)
Zero Adj.
Output 2*Span Adj.
Terminal Cover
*Provided only when the second output is selected.
INSTALLATION
Use Standard Rack (model: 10BXx).
TACHOGENERATOR TRANSMITTER MODEL 10TG
EM-0839 Rev.8 P. 1 / 2
MG CO., LTD. www.mgco.jp
5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
INSTRUCTION MANUAL
TERMINAL CONNECTIONS
Connect the unit as in the diagram below or refer to the connection diagram on the side of the unit.
■EXTERNAL DIMENSIONS unit: mm (inch)
130 (5.12)
3 (.12)
51 (2.01)
82 (3.23)
2–4.3 (.17) dia.
MTG HOLE
TERMINAL COVER
7–M3.5 SCREW
8 (.31)
91 (3.58)
99 (3.90 )
25 (.98)
12
3
56
78
■CONNECTION DIAGRAM
INPUT
+
–
1
OUTPUT 1
2
7
8
+
–
OUTPUT 2
5
6
CONNECTOR
OUTPUT 2*
POWER
*For 1 output channel type, OUTPUT 1 is also connected to the
card-edge connector inside.
Note: The section enclosed by broken line is only for 2nd output channel.
WIRING INSTRUCTIONS
■SCREW TERMINAL
Torque: 0.8 N·m
CHECKING
1) Terminal wiring: Check that all cables are correctly con-
nected according to the connection diagram.
2) Power input voltage: Check voltage supplied to the rack
(model: 10BXx). For the DC power source, be sure that
the ripple level is within 10% p-p.
3) Input: Check that the input signal is within 0 – 100% of
the full-scale.
4) Output: Check that the load resistance meets the de-
scribed specifications.
ADJUSTMENT PROCEDURE
This unit is calibrated at the factory to meet the ordered
specifications, therefore you usually do not need any cali-
bration.
For matching the signal to a receiving instrument or in case
of regular calibration, adjust the output as explained in the
following.
■HOW TO CALIBRATE THE OUTPUT SIGNAL
Use a signal source and measuring instruments of sufficient
accuracy level. Turn the power supply on and warm up for
more than 10 minutes.
1) ZERO: Apply 0% input and adjust output to 0%.
2) SPAN: Apply 100% input and adjust output to 100%.
3) Check ZERO adjustment again with 0% input.
4) When ZERO value is changed, repeat the above proce-
dure 1) – 3).
5) Go through the same procedure for Output 2. Extender
Card (model: 10EC) is required to access the Output 2
Adjustments on top of the unit maintaining electrical
connection at the rear connector.
MAINTENANCE
Regular calibration procedure is explained below:
■CALIBRATION
Warm up the unit for at least 10 minutes. Apply 0%, 25%,
50%, 75% and 100% input signal. Check that the output
signal for the respective input signal remains within accu-
racy described in the data sheet. When the output is out of
tolerance, recalibrate the unit according to the “ADJUST-
MENT PROCEDURE” explained earlier.
LIGHTNING SURGE PROTECTION
We offer a series of lightning surge protector for protec-
tion against induced lightning surges. Please contact us to
choose appropriate models.
10TG
EM-0839 Rev.8 P. 2 / 2
MG CO., LTD. www.mgco.jp
5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Other M-system Transmitter manuals

M-system 10MS User manual

M-system

M-system 10MS User manual

M-system 27U User manual

M-system

M-system 27U User manual

M-system 10RS User manual

M-system

M-system 10RS User manual

M-system Mini-M M2XUM User manual

M-system

M-system Mini-M M2XUM User manual

M-system M80YS User manual

M-system

M-system M80YS User manual

M-system 10JR User manual

M-system

M-system 10JR User manual

M-system B5RS User manual

M-system

M-system B5RS User manual

M-system KWVS2 User manual

M-system

M-system KWVS2 User manual

M-system M2EXV User manual

M-system

M-system M2EXV User manual

M-system SENTRONIC M2SES User manual

M-system

M-system SENTRONIC M2SES User manual

M-system M5VF User manual

M-system

M-system M5VF User manual

M-system MFS2 User manual

M-system

M-system MFS2 User manual

M-system 10VF2 User manual

M-system

M-system 10VF2 User manual

M-system M6DVF User manual

M-system

M-system M6DVF User manual

M-system M3LM User manual

M-system

M-system M3LM User manual

M-system B3FV User manual

M-system

M-system B3FV User manual

M-system Mini-M M2AC User manual

M-system

M-system Mini-M M2AC User manual

M-system 10JRE User manual

M-system

M-system 10JRE User manual

M-system M5 Series User manual

M-system

M-system M5 Series User manual

M-system FJR User manual

M-system

M-system FJR User manual

M-system CT TRANSMITTER User manual

M-system

M-system CT TRANSMITTER User manual

M-system M3LU User manual

M-system

M-system M3LU User manual

M-system 27RS User manual

M-system

M-system 27RS User manual

M-system RB User manual

M-system

M-system RB User manual

Popular Transmitter manuals by other brands

Electro-Voice HTU-2 user manual

Electro-Voice

Electro-Voice HTU-2 user manual

AKG SO 40 SNAPON manual

AKG

AKG SO 40 SNAPON manual

Nokia NWSP Assembly instructions

Nokia

Nokia NWSP Assembly instructions

Vaisala AQT530 Configuration guide

Vaisala

Vaisala AQT530 Configuration guide

Audio Ltd. HX2040 user guide

Audio Ltd.

Audio Ltd. HX2040 user guide

Audiovox S1BTXA Programming guide

Audiovox

Audiovox S1BTXA Programming guide

Vaisala HUMICAP HMT310 user guide

Vaisala

Vaisala HUMICAP HMT310 user guide

Valcom 27A Series manual

Valcom

Valcom 27A Series manual

iSimple JamKast ISFM31 instructions

iSimple

iSimple JamKast ISFM31 instructions

Listen LT-82 user manual

Listen

Listen LT-82 user manual

Xantech HDTXSG01 installation instructions

Xantech

Xantech HDTXSG01 installation instructions

Lectrosonics SMDWB series quick start guide

Lectrosonics

Lectrosonics SMDWB series quick start guide

SkyLink PT-434 User instructions

SkyLink

SkyLink PT-434 User instructions

Halemeier Tri-Mitter MultiWhite2 manual

Halemeier

Halemeier Tri-Mitter MultiWhite2 manual

AlzaPower APW-FMTV2 user manual

AlzaPower

AlzaPower APW-FMTV2 user manual

JTS PT-920B/5 instruction manual

JTS

JTS PT-920B/5 instruction manual

Critical Environment Technologies CGAS-AP installation manual

Critical Environment Technologies

Critical Environment Technologies CGAS-AP installation manual

Dwyer Instruments CDT Series Installation and operating instructions

Dwyer Instruments

Dwyer Instruments CDT Series Installation and operating instructions

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.