MACDEV TACTICAL DRONE User manual
USERS MANUAL
Manufactured by
MacDev Paintball - Australia
macdev.net
TACTICAL DRONE USERS MANUAL
Copyright Mac Developments Pty. Ltd. 2009
All rights reserved
No part of this document may be copied or reproduced in any form or by any means without
-
opments Pty. Ltd., known as indicated in this manual and drawings. All rights of manufac-
-
-
STATEMENT OF LIABILITY
assumes no responsibility for its resale or safe handling. Mac Developments Pty. Ltd. assumes
CAUTION!
This is not a toy. Misuse may cause serious injury or death. Eye protecon designed
specically for paintball must be worn by user and persons within range. Recommend 18
years or older to purchase. Persons under 18 must have adult supervision. READ USERS
MANUAL CAREFULLY BEFORE USING THIS PRODUCT.
CONTENTS
Installing a preset air system
Installing a loader
Understanding the beam sensor
Disabling the beam sensor
About the tourney lock
Debounce (Blue)
Dwell (Red)
Fire mode (White)
Eye mode (Flickering white)
Bolt tracking delay (Flickering green)
Resetting the software
Inline regulator
Drivetrain
INTRODUCTION
manufactured from the highest quality material available using state of the art machining
techniques.
-
macdev website (www.macdev.net) and follow the prompts to register your purchase.
QUICK SETUP
Before installing a preset air system, loosen the
all the way in as shown.
NOTE: when you unscrew the ASA cap to turn the
air o again, your marker usually stores one shot.
Point the marker in a safe direcon to re o that
shot before entering a safe area.
Loosen the feed strap screw, then slide a loader
into the feed tube. Ensure that the loader is pushed
the loader in place using the feed strap screw.
marker is turned on, your indicator LED will use colour to report the beam sensor status.
Red LED - no paintball loaded
will decrease velocity, whilst turning coun-
ter clockwise will increase velocity.
marker.
12" stock barrel
Eye cover screw x2
Eye cover x2
Feed clamp strap
Strap screw
Feed clamp screw
Detent x2
Body
Keg
Keg outside o-ring
(020) x3
Keg switch
o-ring (019)
Bolt Tip
o-ring (014)
Bolt
Powertube
tip o-ring (011)
Powertube
mid o-ring (013)
Powertube
Powertube
rear o-ring (018)
Drive cap
o-ring (019)
Drive cap
End cap
o-ring (020)
End cap
Grip plate
screw x6
Wrap around grip
Grip mount
screw x2
Subplate
screw x2
Subplate
o-rings
Subplate
Subplate
top o-rings
Solenoid
Solenoid
screw x2
Membrane pad
9V alkaline
Bearing
Trigger
spring
Trigger
ASA pin
ASA o-ring
retainer
ASA retainer
o-ring (014)
ASA retainer
o-ring (005)
ASA body
ASA horizontal
bar
Bar o-rings
(005) x2
ASA cap
Hose
Inline cap
Inline sleeve
Filter
Inline bottomworks
Inline swivel
o-ring (015)
Inline cap
o-ring (015)
Inline adjuster
Seat
Inline spring
Inline piston
Inline retainer
inner o-ring (008)
Inline piston
o-ring (016)
Inline regulator
body
Inline top
o-ring (015)
Shroud strap
Shroud cap
Shroud strap
screw
Trigger pin
screw
Trigger
pin
Inline bottomworks
o-ring (018)
Inline o-ring
retainer
Inline retainer
outer o-ring (017)
Shroud
Adjuster
o-ring (008)
Keg inner
o-ring (017)
PARTS LIST
PROGRAMMING YOUR DRONE
-
before playing.
-
solid again.
LED Colour Default
Blue 10
Red Dwell (1ms increments)
White Fire mode 1 (semi)
Green
modes
5 (10bps)
2
2
Purple 3
Flickering Blue -
Flickering Red 2
Flickering White Eye Mode 2 (forced
shot)
Flickering Green 10
2
your marker feeling unresponsive.
dwell will result in very poor performance from your marker, whilst a very high value will
1 Uncapped semi
2 Capped semi
3 Uncapped 3 shot burst
5 Uncapped full auto
marker and hopper. If you use a capped mode (like PSP or
-
ing. For a very fast loader, this may be set to 1, for slow hoppers it should be higher. If your
loader delay is set too low for your loader, then you may experience paintballs breaking in
the breech.
Primarily, you should use the debounce register to remove bounce from your marker.
remove bounce when bounce cannot be removed using the debounce register.
a MacDev tech.
back to you the approximate speed achieved via the colour of the indicator LED.
-
-
MAINTENANCE
this is available seperately in large tubs. Use only genuine seals and parts on your marker to
ensure the best performance.
Please refer to the parts list (centre pages) for a view of the parts contained in your inline
regulator and drivetrain.
1. Piston o-ring
2. Inner retainer o-ring
3. Inline regulator body inside bore (where the piston o-ring slides)
1. Bolt
2. Keg switch o-ring
1 - delayed
2 - forced
3 - test mode with full dwell
Manufactured by
MacDev Paintball - Australia
macdev.net
Table of contents
Other MACDEV Paintball Equipment manuals
