Mackworth TA400 User manual

Doc No. 999562 Revision of document: A
Revision Date: 24.08.21
TA400 Transfer Aid
User Manual

999562 – Revision A Page | 2 of 28
CONTENTS
Safety Instructions and Warnings.......................................................................................................................................... 3
1.1 Introduction....................................................................................................................................................................... 3
1.2 Manufacture...................................................................................................................................................................... 3
1.3 European Authorised Representative ............................................................................................................................... 3
1.4 Symbols Used .................................................................................................................................................................... 4
1.5 Contraindications / Limitations ......................................................................................................................................... 5
1.6 Intended Use ..................................................................................................................................................................... 5
1.7 Warning Notes................................................................................................................................................................... 6
1.8 Operating Environment..................................................................................................................................................... 6
Components/Key Parts .......................................................................................................................................................... 7
Assembly Instructions............................................................................................................................................................ 8
3.1 Unpacking.......................................................................................................................................................................... 8
3.2 Unboxing Transfer Aid....................................................................................................................................................... 8
Operating Instructions ........................................................................................................................................................... 9
4.1 Foot Tray Positioning......................................................................................................................................................... 9
4.2 To Alter the Leg Width .................................................................................................................................................... 10
4.3 Operating Seat Pads ........................................................................................................................................................ 11
4.4 Applying the Brakes......................................................................................................................................................... 11
4.5 Slings................................................................................................................................................................................ 12
4.5.1 Compatible Belt Types............................................................................................................................................ 12
Technical Specification ........................................................................................................................................................ 13
5.1 TA180 Dimensions........................................................................................................................................................... 13
5.2 Specifications................................................................................................................................................................... 14
5.3 Expected Product Lifetime .............................................................................................................................................. 14
5.4 Standards Applied ........................................................................................................................................................... 14
Environmental - Storage and Operating Conditions............................................................................................................ 15
6.1 Normal operating conditions .......................................................................................................................................... 15
6.2 Shipping and storage conditions ..................................................................................................................................... 15
Disposal................................................................................................................................................................................ 15
Fault Finding ........................................................................................................................................................................ 16
General Inspection and Maintenance.................................................................................................................................. 16
9.1 Service ............................................................................................................................................................................. 16
9.2 Inspection ........................................................................................................................................................................ 17
9.3 Cleaning ........................................................................................................................................................................... 17
9.3.1 General Cleaning ................................................................................................................................................ 17
9.3.2 Disinfecting (if necessary) .................................................................................................................................. 17
Warranty.............................................................................................................................................................................. 19
Service Record History ......................................................................................................................................................... 20

999562 – Revision A Page | 3 of 28
Safety Instructions and Warnings
1.1 Introduction
Please read and understand this manual in its entirety before using your Mackworth TA400 Transfer Aid.
The information in this manual is important for the safety of anyone near the Mackworth TA400 Transfer Aid and must be read
and understood to help prevent injuries. It is also crucial to the proper operation and maintenance of the Transfer Aid.
Should any questions arise from reviewing this manual, contact your local authorised representative.
Failure to comply with warnings in this manual may result in; injury to the operator and/or client and/or damage to the Transfer
Aid or related components.
If, during the use of this device or as a result of its use a serious incident has occurred, please report it to the manufacturer and
to your national authority.
Store this manual with the documents included with the Transfer Aid. Contents of this manual are subject to change without
prior written notice.
Do not attempt to use this equipment without first understanding the contents of this manual.
Unauthorised modifications on any Mackworth product may affect its safety. The manufacturer will not be held
responsible for any accident, incident or deficiencies of performance that occur as a result of any unauthorised
modification to its products.
1.2 Manufacture
The Transfer Aid is manufactured at the address below:
Prism Medical UK
Unit 1, Tir Llwyd Industrial Estate, St Asaph Avenue, Kinmel Bay, Conwy, LL18 5JZ
Telephone number: 01924 840100
1.3 European Authorised Representative
The address of the European Authorised Representative for this product:
European Healthcare & Device Solutions (Ireland) Ltd.
Stratton House, Bishopstown Road,
Cork, Ireland.
T12 Y9TC.
Telephone number: [phone]

999562 – Revision A Page | 4 of 28
1.4 Symbols Used
The Table below includes all Symbols from BS EN ISO 15223-1:2016 that can be found in this Manual and on the Product and
what they represent. Refer back to this Table when you are unsure of what a symbol represents.
Consult instructions before use Caution – see instructions for use
Manufacturer
Safe Working Load represents the
maximum load rated for safe
operation
Packaging indicator – This way up Date of manufacture
Serial number Packaging indicator – Keep dry
Please observe local laws on
recycling
For internal use only
Temperature range
Degree of protection provided by
enclosure.
N1: Ingress of particles
N2: Ingress of water
Humidity range Medical Device
Catalogue number European Authorised Representative
Table 1

999562 – Revision A Page | 5 of 28
1.5 Contraindications / Limitations
There are no known “contraindications” associated with the usage of the TA400 Transfer Aid, provided they are used as per
manufacturer’s recommendations and guidelines. However, it is recommended that a client specific assessment is completed by
a trained and knowledgeable health care professional to determine the method of transfer.
Mackworth does not recommend a required number of care givers for the use of our products. This information and
recommendation can only be provided after a thorough personalised, case specific assessment, as there are many factors that
can influence these decisions.
1.6 Intended Use
For internal use only.
The Mackworth TA400 is a sit to stand platform, which is designed to provide an active, safe and comfortable transfer of the
user. It is ideal for short distance transfers, such as to/from bed to chair or from bedroom to bathroom.
Its versatility allows use with wheelchairs, toilet and shower chairs. Soft and wide padding in the leg support improves stability,
the sturdy handle offers grip options for both the user and the carer and also the padded seat paddles which can support the
patient in a comfortable seated position.
The rear wheels with independent locking manual brakes, makes it easy for a carer to manoeuvre, and provides maximum
stability and safety for the user.
The Mackworth TA400 has a safe working load of 180 kg (400 lb), this load must not be exceeded.
The device is used under instruction, and the operation of the aid is undertaken by a trained carer.
A risk assessment must be performed before using any other manufactured Transfer Aid, to ensure safe use can be
established.
The safety belt is a specially designed fabric accessory that attaches to the Transfer Aid by means of buckle incorporated in the
safety belt which clips onto the attachment pins either side of the handle, this holds and aids an individual while the transfer
takes place. The safety belt is supplied separately from the Transfer Aid at the initial time of purchase.
If additional accessories have been supplied with the Transfer aid, refer to the instructions included with those items.
The Transfer Aid:
•Helps to assist a user with sit to stand transfers
•Helps to transfer penitent from one destination to another (i.e. bedroom to bathroom)
•Maximum user weight: 180 kg (400 lb)
•Padded leg support for added comfort
•Padded seat paddles for patient to sit while transferring form one destination to another
•Multiple grip options for both user and carer
•Safety Belt available to enable a carer to support the patient while a transfer is carried out
•Independent locking rear brakes
•The TA400 is intended to be installed on a flat and levelled surface prior to use.
•The Transfer Aid must be installed only by persons authorised by Mackworth or thoaw who have the rights to install
and commission the Transfer Aid safe for use.
•Under no circumstance should the TA400 be put in control of a person who has not been properly trained in the use
and care of this equipment. Failure to adhere to this warning may result in serious injury to the operator and/or the
individual being transferred.
•The Transfer Aid, and associated belts are not toys. Do not use it for unsafe practices. Do not allow children to play with
the Aid or any of its components. The TA400 should not be used for any practice except its intended use.

999562 – Revision A Page | 6 of 28
•In facilities where more than one operator will be responsible for using the Transfer Aid, it is imperative that all such
members be trained on the TA400 prior to use. A training program should be established by the facility to acquaint new
operators with this equipment.
•Your guarantee is void if persons unauthorised by Mackworth perform work on the Transfer Aid.
•To maintain optimum function, the TA400 should be inspected and maintained on a regular basis. See section ‘General
Inspection, Maintenance and Cleaning’ within this user manual.
•The TA400 and the safety belts are intended only for transferring of a person. Mackworth will not be responsible for
any damage caused by the misuse, neglect or purposeful destruction of the Unit, and/or its associated components.
•In areas where children are prone to be present, be vigilant when carrying out a transfer.
•Any accessories used with the TA400 including safety belt, should be checked to ensure that they are in good working
order. Check for signs of wear to each component prior to use. Report any unusual wear to your local authorised
dealer.
•The TA400 and its associated parts are certified to a maximum load of 180kg (400 lb). Do not exceed the maximum
rated load of any of the components.
•Ensure that a clear space is maintained around the Transfer Aid. Before performing a transfer check for and move all
obstacles out of the way.
•Protecting the people present, visually monitor the clipped connection points during transfer stages, so the belt
remains firmly attached to the connection pins.
•To reduce the risk of unintended use, when the TA400 is not in use, remove the Belt from the product to prevent
entrapment or strangulation should the device be tampered with.
•Between Transfer Aid and Belt, the lowest maximum load shall always be used.
You may need to seek specialist advice on how to assist some people with specific moving and handling needs.
Sources of advice include, but is not limited to, professional bodies and organisations, occupational therapist,
physiotherapists, manual handling advisers and ergonomist with experience in health and social care.
1.7 Warning Notes
Your TA400 has been manufactured and tested to exceed BS EN 12182:2012. This does not mean that it can be used
without care. ALL OPERATORS should have read the operating instructions and appreciate this warning section.
1. ALL TA400 are less stable on sloping surfaces. A 5-degree slope is the maximum permitted.
2. ALL TA400 are dangerous to the person being transferred when used recklessly or pushed at speed.
3. ALL TA400 are less stable when the load is moving.
1.8 Operating Environment
The TA400 is intended for use within the professional health care facility environment as well as the home health care
environment. The Transfer Aid is not suitable for any other environment or special environments.
The Transfer Aid is not intended to be used in environments where there are rapid changes in the environmental temperature
and humidity during intended use.

999562 – Revision A Page | 7 of 28
Components/Key Parts
Please see below to familiarise yourself with the components of the TA400. The images below show the contents of the Transfer
aid. If you have not received all the components contact your Mackworth dealer immediately – contact details are provided on
the last page of this manual.
Item
Description
1
Handle
2
Safety Belt Clip Pins
3
Seat Pads
4
Knee Pad
5
Leg Lever Plate
6
Foot Tray
7
Braked Rear Castor
8
Front Castor
9
Serial Number Label
Figure 1
1
3
4
6
7
8
5
2
Table 2

999562 – Revision A Page | 8 of 28
Assembly Instructions
3.1 Unpacking
The Transfer Aid will arrive to you in a robust box, please be careful when removing the components from the box.
Please read the user guide in full before operating.
When lifting the Transfer Aid, a two person lift is required.
This user manual should be kept safe for future reference.
The Transfer Aid has been specifically designed to be installed in both the professional and home health care environments.
No matter the environment, health and safety factors should be considered to ensure the safety and essential performance of
the Transfer Aid and to avoid unnecessary damage or injuries to people within the area of the Transfer Aid.
The environment in which the Transfer Aid is situated in, whilst carrying out a transfer, is required to be on a flat surface with no
steep inclines.
3.2 Unboxing Transfer Aid
When using a sharp knife, be careful not to damage the product.
This section will summarise the layout of the Transfer Aid packaging and what is included in the box. It is recommended a knife is
used for smoother unpacking of the Transfer Aid. The Transfer Aid is packed into a single box 1200mm x 800 mm x 1200 mm
(47.25 inch x 31.5 inch x 47.25 inch), weighing approximately 42kg (93 lb).
Using a knife to release the top lid of the box, the box should open, and the internal packaging must be removed to access the
product. It will include all the following components. It is recommended that the components are removed in the numerical
order below.
1. Fully Assembled TA400 Transfer Aid
2. User Manual

999562 – Revision A Page | 9 of 28
Operating Instructions
The Transfer Aid may be heavy for users and will need to be lifted with care, please operate the device with the use
of the castors wherever possible to prevent any injury.
Before use, you should familiarise yourself with use of the TA400, the procedure for opening / closing the leg and the positioning
of clients when opening or closing the seat pads.
Appropriate training in lifting and handling procedures should be undergone by any person operating a Transfer Aid, for their
own and the client’s safety and comfort. These instructions are designed to cover the method of using the Transfer Aid.
4.1 Foot Tray Positioning
The Foot Tray is fitted onto the base by locating it onto the 2 location pins that are positioned either side of the central
leg lever bracket (arrowed below), as shown in (figure 4)
Optional – There is an option to incorporate a retaining clip to the Foot Tray.
Figure 4
Figure 5

999562 – Revision A Page | 10 of 28
4.2 To Alter the Leg Width
The legs on the base unit of the Transfer Aid are operated by adjusting the leg lever plate, as shown in the photo below.
To open the legs, press on “open” (Red Arrow) and then to close the legs, press on “close” (Blue Arrow). Transfer Aid
manoeuvres can be completed with the legs in any position.
Figure 6
Figure 7
Figure 8
Figure 9

999562 – Revision A Page | 11 of 28
4.3 Operating Seat Pads
Operating the Seat Pads position on the TA400, in the following way:
1. On the front face of the product, take one hand and holding the base of each seat (See Figure 10), pull upwards in an
arc movement until it reaches the open position. (See Figure 11)
2. Once the patient is stood safely on the Transfer Aid, use of safety belt if patient requires support aid, carer can carry
out the process of repositioning the Seat Pads.
3. Using your hands, grab the Seat Pads (shown in Figure 12) and rotate them around until they reach the closed position.
Make sure the seat pads are position in the correct position before allowing the patient to sit.
4.4 Applying the Brakes
Operate the TA400 Transfer Aid brakes, in the following way to activate and deactivate the brakes:
1. To activate the rear castor brakes, take your foot and push down vertically on the brake lever. (Shown in Figure 13).
2. To deactivate the brakes, place your foot below the brake lever and lift the brake lever upwards. (Shown in Figure 14).
Figure 13
Figure 14
Figure 12
Figure 10
Figure 11

999562 – Revision A Page | 12 of 28
4.5 Slings
Sling Clips should be attached as follows:
1. Hold the Sling Clip in your hand and attach the clip onto the Safety Belt Clip Pin on the Transfer Aid.
2. Once the Clip is secure, position the Belt around the lower back of the patient, ensuring the elasticated section is placed
on the user’s lumbar spine and the solid section is place under the user’s coccyx. Hold onto the other Sling clip with
your hand.
3. Ensure the Rear Castor brakes are applied.
4. With the Belt secured on one side of the Transfer Aid, and the other by the caregivers’ hand, the patient may safely lift
themselves onto the Transfer Aid, using the Safety belt as an assistive product only.
5. Do not use the belt to raise the patient, the patient must be able to lift themselves, with the belt being a support.
6. While the patient is being lifted, once possible, attach the Safety Belt to the second Clip Pin on the Transfer Aid.
7. Safety Belt operation complete.
To remove the sling, simply reverse the processes shown in the above statements.
4.5.1 Compatible Belt Types
We recommend the use of the Mackworth manufactured belt range (type ‘B’
applied part) to be utilised with the Mackworth TA400. It is at the user’s
discretion to use alternative supplied product. In utilising another
manufacturer’s belt, checks must first be made to ensure the belt is safe to
use and meets the requirements of BS EN ISO 10535 before its use.
The belts with a safe working load of 180kg (400 lb) that can be used with the
Mackworth TA400 are shown below in Table 3, complete with product codes.
For all components, the lowest maximum safe working load must always be
adhered to.
Size Mackworth Belt Range - Product Codes
Mackworth TA400 Back Support Belt
Small 1201TAB550C
Medium 1201TAB540C
Large 1201TAB530C
XL 1201TAB520C
Figure 15
Table 3

999562 – Revision A Page | 13 of 28
Technical Specification
5.1 TA400 Dimensions
All dimensions below are shown in millimetres.
Figure 16
Figure 17
Figure 18
Figure 19

999562 – Revision A Page | 14 of 28
5.2 Specifications
Dimensions
Turning Circle
1010 mm (39.75”)
Overall Height
1001 mm (39.4”)
Overall Width
680 mm (26.75”)
Ground Clearance
35 mm (1.35”)
Front and Rear Castors
100 mm (3.94”)
Table 4
Weights
Safe Working Load (SWL)
180 kg (400 lb)
TA400 – Full Product
38 kg (83.75 lb)
Foot Tray
5.5 kg (12.1 lb)
Table 5
Operational Forces
Operating Force with 180 kg (400 lb)
57 N (12.8 lbf)
Operating Force with 0 kg (0 lb)
20 N (4.5 lbf)
Brakes
35 N (7.9 lbf)
Seat Pads
18 N (4.0 lbf)
Table 6
5.3 Expected Product Lifetime
10 yrs. depending usage and compliance to maintenance, servicing and LOLER inspections.
5.4 Standards Applied
The standards that have been applied to the device are as follows:
•EN 12182:2012 Assistive products for persons with disability – General requirements and test methods

999562 – Revision A Page | 15 of 28
Environmental - Storage and Operating Conditions
The Transfer Aid is intended for internal use within normal environmental conditions.
It is not intended to be used in environments where there are rapid changes in the environmental temperature and humidity
during intended use.
6.1 Normal Operating Conditions
+5°C to +40°C (41°F to 104°F) at a relative humidity between 15% to 90% RH, non-condensing but not requiring a water vapour
pressure greater than 50hPa and atmospheric pressure between 700hPa to 1060hPa
6.2 Shipping and Storage Conditions
-25°C to +5°C (-13ºF to 41ºF) with any humidity level.
+5°C to +35°C (41°F to 95°F) at a relative humidity up to 90%.
+35°C to 70°C non-condensing at a water vapour pressure up to 50hPa.
Disposal
When the Transfer Aid has completed its life cycle and can no longer perform to its intended use safely the Aid
must be decommissioned by an approved Service Engineer. The following specifies the importance of correct
disposal procedure including local laws and being environmentally friendly.
Please observe the local laws on recycling and respect the current laws for disposal within the community the
device is being used within. If there is any uncertainty of the below guidelines, contact your local authorities to
determine the proper method of disposal of potentially biohazardous parts and accessories.
The relevant components utilised in the manufacture of the device that can be recycled at the end of the
device life are:
Fully recyclables:
Consideration when Recycling:
Steel frame (Frame, Foot tray)
Knee Pad
Castors
Seat Pads
Initial packaging of the device (cardboard)
Metallic fixing – screws etc.
The product may be contaminated and has to be disinfected before recycling or disposal.
See section 9.3 ‘Cleaning’ for details of how to do this.
Table 7

999562 – Revision A Page | 16 of 28
Fault Finding
Should a problem arise with the use of the Transfer Aid, review the Table below.
Find the fault and complete the recommended solution.
If the fault is not found and/or the solution does not correct the problem, contact your local Mackworth authorised dealer
immediately – contact details are provided on the last page of this manual.
Fault
Action
Castors do not operate.
Ensure the brake has been fully disengaged, Check the castors are free running
Check the castors are touching the ground. If this does not correct the fault, then
contact your local authorised dealer immediately so the Transfer Aid can be checked
to ensure proper continued operation.
Movement is compromised by
excessive force required to move the
Aid
Check the castors are not fouled with debris that would restrict its movement (clean
out, test and return to service) If this does not correct the fault, then contact your
local authorised dealer immediately so the Transfer Aid can be checked to ensure
proper continued operation.
Movement is restricted
Damaged footplate that is catching on the floor level. Remove and place out with
new - contact your local authorised dealer immediately so that parts can be
changed and the Transfer Aid can be checked to ensure proper continued operation.
Brakes do not operate
Ensure that the brake mechanism is fully engaged, check to see if both rear casters
are touching the ground. If this does not correct the fault, then contact your local
authorised dealer immediately so the Transfer Aid can be checked to ensure proper
continued operation.
General Inspection and Maintenance
9.1 Service
No service is to be carried out on the TA400 Transfer Aid while transferring a person to reduce the risk of injury.
Service must be completed by a Mackworth authorised Service Engineer.
Do not attempt to service the product yourself, or warranty is void.
To ensure the safety and continued good function of your Transfer Aid, routine service must be performed on your Transfer Aid.
Service should be completed by a Mackworth approved service engineer every 6 months to ensure the products required
standard is maintained. The service history of the product should be documented each service in the Service Log at the back of
this User Manual.
When the Transfer Aid is serviced, the 6 month service checklist must be completed for the Transfer Aid.
Service Manual Document Number: 995562.
Spare Parts Manual Document Number 992562.
The Service must be completed every 6 months after installation of the Transfer Aid to comply with LOLER Regulations.
The Transfer Aid has an expected Service Life of 10 Years.
Contact your local authorised Mackworth dealer if you:
•Need more information.
•Have any questions about the use or service of your Transfer Aid.
•Notice any change in the performance.
•Want to report an unexpected occurrence.
•Want to arrange a service.
•Need to ascertain necessary information for replacement parts and components.
Contact details of your local Mackworth dealer are shown on the last page of this manual
Table 8

999562 – Revision A Page | 17 of 28
9.2 Inspection
Inspection is to be completed prior to each use by the user of the Transfer Aid.
Should any of the components in the table below fail the inspection, DO NOT use the Transfer Aid.
Contact your local authorised dealer for service – contact details are on the last page of this manual.
Ensure all component inspections in the Table below are completed prior to each use of the Transfer Aid.
Check List before Use
Component
Service/Inspection required
Generic
Visual inspection of the external of the Transfer Aid. Significant damage that may
affect the function of the Transfer Aid along with a clear safety hazard is
unacceptable.
Check the Labelling on the Transfer Aid to ensure they are all still legible, this
includes the Serial Number and other important markings. If labels are not legible,
then contact your local authorised dealer immediately.
Check all main nuts and bolts to see if they are loose, If they are not tight or you
have concerns, then contact your local authorised dealer immediately.
Examine the sling clips on the handle bar for excessive wear and sharp edges.
Knee Pad
Inspect the Knee Pad for damage including cuts and breaks.
Seat Pads
Ensure seat pads swivel smoothly and there are no signs of damage such as
permanent deformation and/or cracks, breaks. Both Pads should align when in
closed position.
Brakes
Ensure the Brakes function when activated.
Ensure the Transfer Aid can move freely when the Brakes are deactivated. (Ensure
they aren’t rubbing on the Wheels).
Castors and Wheels
Examine the products Wheels and Castors for signs of damage or wear, ensure they
run freely and are not cracked.
Check to see all castors are flat on the floor and Transfer Aid is stable.
Ensure the product is able to rotate freely with ease.
Foot Tray
Ensure the Foot Grips are still applied and undamaged. Check Foot Tray for
permanent deformation.
Leg Pivot Points
Check the smooth opening and closing of the legs.
Belts
Examine belts for fraying or other damage. DO NOT use belts with fraying or
damage to the suspension straps or tears in the body of the sling.
9.3 Cleaning
Please follow the cleaning guidelines below on cleaning and disinfecting the Transfer Aid.
9.3.1 General Cleaning
It is recommended to clean the Mackworth TA400 and accessories before use by a different person, reducing the risk
of cross–contamination.
The exterior of the Mackworth TA400 can be cleaned using a damp soapy cloth for general cleaning duties. Please ensure the
cloth is damp and not wet. Ensure the exterior of the device is dry after cleaning. Dry using a clean dry cloth.
9.3.2 Disinfecting (if necessary)
Should the Transfer Aid require a more thorough clean, the use of the Actichlor™ disinfectant product (which is widely available
in tablet form and used throughout the health care industry) is recommended.
Table 9

999562 – Revision A Page | 18 of 28
Follow the manufacturer’s safety instructions for the use of the cleaning product before use to ensure safe use for
the operator and the patient.
Ensure the cloth is damp before the cleaning process.
Application is through a clean damp cloth applied to wipe the device down. Use in the following dilutions to ensure an effective
clean:
•Actichlor™ dissolvable chlorine tablets provide a concentration of 1000 ppm of available chlorine (0.1%) per 1 tablet
•1 tablet (1.7g formed tablet (x1) will create a virucidal solution, diluted in 1 litre of water to provide effective means to
clean a “dirty” device. This is also ideal for use after an outbreak of the Norovirus/winter vomiting and can be used as a
precaution against C.Diff. It is effective against viruses, bacteria, spores, yeasts and moulds.
•The contact time against the outer components of the device should be for 5 minutes to prevent any virucidal
infections without a degradation to the functionality of the device. 5 minutes is a recommended contact time. The
device can withstand a longer contact period but the 5 minute recommendation as a minimum must be followed to
provide an effective cleaning regime.
•Blood spills should be dealt with by an increased concentration of the solution – please refer to the instructions on the
manufacturers product labelling.
Dilution chart
Product used as
Device condition
Concentration
(ppm)
Dilution qty* (l)
Tablets per 1l
(0.26gal)
Contact time
(minutes)
Bactericidal
Clean
200
5 (1.32gal)
1
1
Dirty
1000
1 (0.26gal)
1
5
Yeasticidal
Clean
200
5 (1.32gal)
1
1
Dirty
1000
1 (0.26gal)
1
5
Fungicidal
Clean
2000
1 (0.26gal)
2
15
Dirty
5000
1 (0.26gal)
5
15
Mycrobactericidal
Clean
1000
1 (0.26gal)
1
15
Dirty
5000
1 (0.26gal)
5
15
Virucidal
Clean
500
2 (0.53gal)
1
5
Dirty
1000
1 (0.26gal)
1
5
Sporcidal (C.Diff)
Clean
1000
1 (0.26gal)
1
10
-
-
-
-
-
Sporcidal
Clean
5000
1 (0.26gal)
5
10
-
-
-
-
-
* Dilution is made with water. DO NOT dilute within any other medium.
•When diluted in water, one tablet gives 1000ppm of available chlorine.
•The concentration of the solution depends upon whether the object being cleaned is noticeably dirty (indicated
in the table by “Device condition”.
Table 10

999562 – Revision A Page | 19 of 28
Handling and storage safety precautions when using this cleaning agent:
Advice on Safe Handling
Avoid contact with skin and eyes.
Do not breathe dust/fumes/gas/mist/vapours/spray.
Use only with adequate ventilation.
Wash hands thoroughly after handling.
Mixing this product with acid or ammonia releases chlorine gas.
Hygiene Measures
Handle in accordance with good industrial hygiene and safety practice. Remove and wash contaminated clothing before re-use.
Wash face, hands and any exposed skin thoroughly after handling.
Conditions for Safe Storage
Keep out of reach of children.
Keep container tightly closed.
Store in suitable labelled containers.
Storage temperature: 0-25°C (32-77°F).
Individual Protective Measures
Hand protection: Gloves
Dissolve
Dissolve in cold water – With no agitation, 1 tablet will take approximately 10 minutes to fully dissolve in the water used.
The information above has been extracted from the Actichlor™ MSDS (Manufacturers Safety Data Sheet). For a full review of the
data please follow the link below:
http://www.nhsggc.org.uk/media/236215/msds-actichlor-plus.pdf
Warranty
This guarantee does not affect or in any way limit your Statutory Rights.
1. Mackworth guarantees the Mackworth TA400, supplied as new, against failure within the period of 36 months from the
date of purchase by virtue of defects in material or workmanship.
2. The liability of Mackworth under terms of this guarantee shall be limited to the replacement or the defective part(s) to
the sales distributor, dealer, agent, person or entity which purchased the equipment from Mackworth. In no event shall
Mackworth incur liability for any consequential or unforeseeable losses.
3. This equipment guarantee shall be void if the equipment is not serviced by Mackworth or its authorised agents, in
accordance with manufacturer’s recommendations, or if any unauthorized persons carry out work on the equipment.
4. This guarantee does not apply to failure attributable to normal wear and tear, damage by natural forces, user neglect or
misuse or to deliberate destruction.
5. Do not attempt to service the product yourself, or warranty is void.

999562 – Revision A Page | 20 of 28
Service Record History
Complete this section after each service, repair inspection and/or maintenance.