MAHA ECONLIFT 6500 User manual

Fehler! Verwenden Sie die Registerkarte 'Start', um Name dem Text zuzuweisen, der hier angezeigt werden soll.Fehler! Verwenden Sie
die Registerkarte 'Start', um Name dem Text zuzuweisen, der hier angezeigt werden soll.Fehler! Verwenden Sie die Registerkarte
'Start', um Name dem Text zuzuweisen, der hier angezeigt werden soll.
ECONLIFT 6500
Two Post Lift
Original Operating Instructions
BA361601-en
Pos: 1 / Te chnisc he D okumen tati on/Heb etec hnik/ 36 S äule n-Heb ebü hne n/ 16 01 EC ON LIF T 6500/BA/Inhalt:3616 Titelbild @ 46\mod_1481288659643_0.docx@ 2797767@ @ 1
Pos: 2 / -----F or m at---- -/MAN UEL LER UMB RUC H Seite numb r uc h @ 0\mod_ 11 344 03 5 776 87_ 0.d oc x @ 1 277 @ @ 1

2
BA361601-en
Pos: 3 / -----F or m at---- -/Inh a ltsv e rz eic hn is - 3E be ne n @ 5\m od_ 11 6 8867 4 41 046_ 7 5.d oc x @ 72 920 @ @ 1
Contents
1Safety ......................................................................................................................5
1.1 Introduction......................................................................................................................................... 5
1.2 Symbols .............................................................................................................................................. 5
1.3 Intended Use....................................................................................................................................... 5
1.4 Inappropriate Use................................................................................................................................ 5
1.5 Requirements on Operating and Service Personnel............................................................................. 5
1.6 Safety Instructions for Commissioning................................................................................................. 6
1.7 Safety Instructions for Operation ......................................................................................................... 6
1.8 Safety Instructions for Servicing........................................................................................................... 7
1.9 What to Do in the Event of Defects or Malfunctions............................................................................. 7
1.10 What to Do in the Event of an Accident............................................................................................... 7
1.11 Safety Features ................................................................................................................................... 8
1.11.1 Dead Man's Type Control.................................................................................................................... 8
1.11.2 Electronic Synchronization System...................................................................................................... 8
1.11.3 Safety Nut ........................................................................................................................................... 8
1.11.4 Load Nut Failure Protection................................................................................................................. 8
1.11.5 Load Nut Wear Check......................................................................................................................... 8
1.11.6 Overload Protection of Motors............................................................................................................. 8
1.11.7 Drive Belt Failure Protection................................................................................................................. 8
1.11.8 Pinch Point Protection......................................................................................................................... 8
1.11.9 Automatic Arm Restraint ..................................................................................................................... 8
2Description...............................................................................................................9
2.1 General Information ............................................................................................................................. 9
2.2 Specifications ...................................................................................................................................... 9
3Transport and Storage ...........................................................................................12
4Installation and Initial Operation ..............................................................................12
5Operation...............................................................................................................12
5.1 Main Switch....................................................................................................................................... 12
5.2 Controls and Indicators ..................................................................................................................... 13
5.3 Text Display....................................................................................................................................... 14
5.3.1 Normal Operation.............................................................................................................................. 14
5.3.2 Referenzierung .................................................................................................................................. 15
5.3.3 Error Messages with Service Requirement: E000…E199 .................................................................. 15
5.3.4 Error Messages: E200…E299 ........................................................................................................... 16
5.4 Menu Navigation ............................................................................................................................... 17
5.4.1 Exploded View .................................................................................................................................. 17
5.4.2 Preselecting the Automatic Stop ....................................................................................................... 17
5.4.3 Disabling the Automatic Stop ............................................................................................................ 17
5.4.4 Displaying the Serial Number of the Lift ............................................................................................. 18

3
BA361601-en
5.4.5 Displaying the Serial Number of the Lift Control................................................................................. 18
5.4.6 Displaying the Cloud ID ..................................................................................................................... 18
5.5 Arm Restraint .................................................................................................................................... 19
5.6Preparations...................................................................................................................................... 20
5.7 Raising .............................................................................................................................................. 22
5.8 Vehicle in Raised Position.................................................................................................................. 22
5.9 Lowering ........................................................................................................................................... 22
5.10 Manual Lowering............................................................................................................................... 23
6Maintenance ..........................................................................................................24
6.1 Annual Inspection.............................................................................................................................. 24
6.2 Maintenance Schedule ...................................................................................................................... 25
6.3 Care Instructions ............................................................................................................................... 25
6.4 Lubrication ........................................................................................................................................ 26
6.4.1 Lubricants ......................................................................................................................................... 26
6.4.2 Lifting Screw Lubrication ................................................................................................................... 26
6.4.3 Upper Support of Lifting Screw ......................................................................................................... 27
6.4.4 Greasing the Arm Extensions ............................................................................................................ 27
6.4.5 Greasing the Disc Adapter Threads................................................................................................... 27
6.5 Operational and Wear Checks........................................................................................................... 28
6.5.1 Load Nut Wear Check....................................................................................................................... 28
6.5.2 Checking the Rubber Pads of the Support Discs .............................................................................. 29
6.5.3 Checking the Brakes of the Lifting Screws ........................................................................................ 29
6.5.4 Checking the Drive Belt ..................................................................................................................... 29
6.5.5 Checking the Circuit Breaker............................................................................................................. 30
6.6 Spare Parts ....................................................................................................................................... 30
7Service Lifetime......................................................................................................31
8Dismantling ............................................................................................................31
9Disposal.................................................................................................................31
10 Contents of the Declaration of Conformity ..............................................................31
11 Company Information.............................................................................................32
Pos: 4 / -----F or m at---- -/MAN UEL LER UMB RUC H Seite numb r uc h @ 0\mod_ 11 344 03 5 776 87_ 0.d oc x @ 1 277 @ @ 1

4
BA361601-en
Pos: 5 / -----F or m at---- -/MAN UEL LER UMB RUC H Seite numb r uc h @ 0\mod_ 11 344 03 5 776 87_ 0.d oc x @ 1277 @ @ 1

5
BA361601-en
Pos: 6 / Te chnisc he D okumen tati on/A lle Ger ä te/Üb erschrif te n/Übers chr iften 1/S / Überschr ift 1: Sich erhei t @ 6\mod_1174482399906_75.docx@ 76962@ 1 @ 1
1
Safety
Pos: 7 / Te chn isc he Dokum en tat ion/ A ll e G er ä te/ Übe rs chrif te n/ Über s c hrift en 1.1/E/ Übe rs c hrif t 1.1: E inf ühru ng @ 6\m od_1174482219062_75.docx@ 76793 @ 2 @ 1
1.1
Introduction
Pos: 8 / Te chnisc he D okumen tati on/Heb etec hnik/ 36 S äule n-Heb ebü hne n/ 26 01 EC ON III /BA /I nha lt: 3626 E inf ühr u ng @ 27\mod_1328083636960_75.docx @ 1532697@ @ 1
Thoroughly read this manual before operating the lift and comply with the
instructions. Always display the manual in a conspicuous location.
Personal injury and property damage incurred due to non-compliance with these
safety instructions are not covered by the product liability regulations.
Pos: 9 / Te chnisc he D okumen tati on/A lle Ger ä te/Üb erschrif te n/Übers chr iften 1 .1/S/ Über schri ft 1. 1: Sy mbo le @ 6\mod_1174482270875_75.docx@ 76865@ 2 @ 1
1.2
Symbols
Pos: 10 /Techn ische Dokume ntation/Al leG eräte/Inh alte/Sicher heit/Inhal t:Sy mbole Sicher heit_12pt @ 2 5\mod_1324456650897_75.docx@ 1139046@ @ 1
Important safety instructions. Failure to comply with instructions could result in
personal injury or property damage.
Important information.
Pos: 1 1 / Techn ische Dokument atio n/Alle Geräte/Üb ersc hrift en/ Überschr ifte n 1.1/ B/ Überschr ift 1. 1: Bes timm ungsg emä ßer Geb rau ch @ 6\m od_117 6734 02220 3_75.d ocx @ 8 8746 @ 2 @ 1
1.3
Intended Use
Pos: 1 2 / Techn ische Dokument atio n/Heb etech nik/3 6 Säul en-Heb ebüh nen/ 0001 S äulen -Hebeb ü hnen A lle/I nhal te/In halt: Bestimm ungs gemä ßer Geb ra uch Sc her en-/ Sä u le n-H BZ_ 12p t @ 26\m od_1326280285347_75.docx@ 1151787@ @ 1
•This lift is to be used exclusively for the safe lifting of motor vehicles. Observe
the rated load capacity.
•The lift may not be modified without the express written consent of the
manufacturer. In case of non-compliance the declaration of conformity
becomes void.
Pos: 1 3 / Techn ische Dokument atio n/Alle Geräte/Üb ersc hrift en/ Überschr ifte n 1.1/ B/ Überschr ift 1. 1: Bes timm ungsw idr iger Geb rauc h @ 18\mod_1255530265027_75.docx@ 471571 @ 2@ 1
1.4
Inappropriate Use
Pos: 14 /Techn ische Dokume ntation/Heb etechnik/ 00 HBZ Alle/I nhalte/In halt: Bestimmun gswidrig erG ebrauch HBZ _12pt @ 26\mod_1325512462855_75.docx @ 1143595@ @1
Any use other than described is inappropriate, for example:
•Climbing on the lift supports
•Transporting persons on the lift supports
•Usage as mobile work platform or for other lifting operations
Pos: 1 5 / Techn ische Dokument atio n/Alle Geräte/Üb ersc hrift en/ Überschr ifte n 1.1/ A/Über schr ift 1.1: Anf ord erungen an das Bedien ungs - und Servicep ersonal @ 3 4\mod_1380637497630_75.docx@ 1835413@ 2 @ 1
1.5
Requirements on Operating and Service Personnel
Pos: 16 / Techn ische Dokument ation/ Alle G eräte/ Inhal te/Sich erheit/I nhalt: Anforder ungen a n das Bedie nungs- und Ser viceper sonal_12p t @ 47\mod_1482392891402_75.docx @ 2803198@ @ 1
All persons employed in the operation, maintenance, installation, removal and
disposal of the device must
•be mentally and physically suited for these activities,
•be at least 18 years old,
•be trained and instructed in writing,

6
BA361601-en
•have read and understood the operating instructions, especially the instructions
what to do in the event of defects or malfunctions,
•be on record as having been instructed in safety guidelines,
•have practical experience in working with vehicle lifts and the hazards inherent
in such equipment.
Pos: 17 /Techn ische Dokument ation/Alle Ger äte/Übersc hriften/ Üb er schr i fte n 1. 1/ S/Üb er sc hr if t 1. 1: S ic herhe it s vor schr ift en f ür die I nbe tr ieb nahm e @6\m od_1174482269156_75.docx@ 76838 @ 2 @ 1
1.6
Safety Instructions for Commissioning
Pos: 18 /Techn ische Dokume ntation/Heb etechnik/ 00 HBZ Alle/I nhalte/In halt: Sicher he itsv or schr if te n f ür d ie I nb etri eb na hme H BZ_ 12p t @ 4 7\mod_1483524035338_75.docx@ 2804458@ @1
•The lift shall be installed and commissioned by authorised service personnel
only.
•Use personal protective equipment.
•All safety features must be checked for proper function at commissioning.
•The control desk (if present) shall not be installed in the danger zone of the lift.
•The standard lift version shall not be installed and commissioned in hazardous
locations, outdoors, in moist rooms (e.g. car wash) or outside a temperature
range of 5…40 °C (41…104 °F).
Pos: 1 9 / Techn ische Dokument atio n/Alle Geräte/Üb ersc hrift en/ Überschr ifte n 1.1/ S/Über schr ift 1.1: Sic herhe itsv orschr iften f ür d en B etri eb @ 6\mod_1174482268953_75.docx@ 76826 @ 2 @ 1
1.7
Safety Instructions for Operation
Pos: 2 0 / Techn ische Dokument atio n/Heb etech nik/3 6 Säul en-Heb ebüh nen/ 0001 S äulen -Hebeb ühnen Alle/ Inhalte/In halt: Sicher heitsvorsc hriften für den Be trieb Säule n-HBZ_ 12p t @ 46\mod_1481283829688_75.docx@ 2797291@ @ 1
•Use personal protective equipment.
•Operation of the lift is permitted only with all protective covers (motor, spindle,
cylinder cover) correctly installed and undamaged.
•Drive on the lift only when it is in bottom position.
•Ensure an unobstructed movement of lift and vehicle.
•After raising the vehicle briefly, stop and check the lift supports for secure
contact with the vehicle.
•Make sure the vehicle doors are closed during raising and lowering cycles.
•Closely watch lift and vehicle during raising and lowering cycles.
•Do not allow anyone to stay in lift area during raising and lowering cycles.
•Do not allow anyone to climb on lift or inside raised vehicle.
•Comply with the applicable accident prevention regulations.
•Do not exceed the rated load capacity as indicated on the lift nameplate.
•Only use the vehicle manufacturer's recommended lift points.
•Do not use the lift for transporting persons.
•Lifts with runways: After positioning the vehicle on the lift secure it against roll-
off.
•Keep lift and vehicle free of tools and parts.
•Lifts with support arms: Use caution when removing or installing heavy
components. Center-of-gravity displacement may occur. Secure the vehicle
using lashing straps.

7
BA361601-en
•Keep the lift and lift area clean. Slip hazard on oily surface!
•The main switch serves as emergency switch. In case of emergency turn it to
position "0".
•Protect all parts of the electrical equipment from humidity.
•Protect the lift against unauthorized usage by padlocking the main switch.
•Use caution with operating vehicle engines. Danger of poisoning!
Pos: 2 1 / Techn ische Dokument atio n/Alle Geräte/Üb ersc hrift en/ Überschr ifte n 1.1/ S/Über schr ift 1.1: Sic herhe itsv orschr iften f ür S ervicearb eiten @ 6\mod_1174482270640_75.docx @ 76850@ 2 @ 1
1.8
Safety Instructions for Servicing
Pos: 2 2 / Tec hnisch e Dok ument ation/H ebetech nik/0 0 HBZ Alle/Inhal te/In halt: S icher heitsv orschrif ten f ür Serv icearb eiten H BZ_ 12pt @ 46\mod_1481283945452_75.docx@ 2797338@ @ 1
•Use personal protective equipment.
•Service work must be done by authorized service technicians.
•Turn off and padlock the main switch before doing any repair, maintenance or
setup work.
•The system must be unpressurized during maintenance work.
•Work on pulse generators or proximity switches must be done by authorized
service technicians.
•Work on the electrical equipment must be done by service technicians or
qualified electricians.
•Ensure that ecologically harmful substances are disposed of in accordance with
the appropriate regulations.
•Do not use high pressure or steam jet cleaners. Do not use caustic cleaning
agents.
•The lift's safety devices must be set by authorized service technicians.
•Do not replace or override the safety devices.
Pos: 2 3 / Techn ische Dokument atio n/Alle Geräte/Üb ersc hrift en/ Überschr ifte n 1.1/ V/Über sc hrift 1 .1: V erh alten im St örfal l @ 6\mod_1178097008375_75.docx@ 90829@ 2 @ 1
1.9
What to Do in the Event of Defects or Malfunctions
Pos: 24 /Techn ische Dokume ntation/Heb etechnik/ 00 HBZ Alle/I nhalte/In halt: Verhalten im S törfall HBZ_1 2pt @ 26\mod_ 13 25 513 6 825 83_ 7 5.do cx @ 11 43723@ @ 1
•In case of defects or malfunctions such as uncontrolled lift movement or
deformation of the superstructure, support or lower the lift immediately.
•Turn off the main switch and secure it against unauthorized usage. Contact
service.
Pos: 2 5 / Technische Do kumentat ion/Alle Gerät e/Übersc hriften/Über schrifte n 1.1/V/Übers chrift 1.1: Verh alten bei Unfä llen @ 19\mod_ 126 71772 45337_ 75.do cx @ 794 600 @ 2 @ 1
1.10
What to Do in the Event of an Accident
Pos: 26 /Techn ische Dokument ation/Alle Ger äte/Inhal te/Sicher he it/I n halt: Verha lt en be i Unfä llen_ 12p t @3 4\mod_1381128863435_75.docx@ 1837175@ @1
•The injured person is to be removed from the danger area. Find out where
dressing and bandages are kept. Seek first-aid.
•Provide first-aid (stop bleeding, immobilise injured limbs), report the accident
and seal off the accident site.
•Immediately report any accident to your supervisor. Make sure a record is kept
of every occasion first-aid is provided, e.g. in an accident book.
•Remain calm and answer any questions that may arise.
Pos: 2 7 / Tec hnis ch e Dokume nt at ion/ Al le G erä te/ Übe rs c hrift en/ Über sc hri fte n 1.1/S/ Über sc hr if t 1.1: S ic her he its ei nric ht un ge n @ 6\mod_ 11744 83324 765_ 75.do cx @ 7710 3 @ 2 @ 1

8
BA361601-en
1.11
Safety Features
Pos: 2 8 / Techn ische Dokument atio n/Heb etech nik/0 0 HBZ Alle/In halte/In halt: Sicherhe itseinr ichtu ngen -V er ä nder un ge n ver b ote n H BZ @ 4 7\mod_1483610856889_75.docx@ 2804716 @ @ 1
•The safety features shall not be modified by the owner/operator!
Pos: 2 9 / Techn ische Dokument atio n/Heb etech nik/3 6 Säul en-Heb e büh ne n/ 160 1 EC ON LI FT 6500/ BA/ Inh al t: 3616 S ic her he its einr ic ht un gen @ 46\mod_1481106169539_75.docx @ 2794441@ 333333333@1
1.11.1
Dead Man's Type Control
The operator is required to hold the main switch in the engaged position to raise
or lower the lift.
1.11.2
Electronic Synchronization System
The synchronization system ensures level movement of both carriages.
Synchronization is electronically controlled by the motors switching on and off.
Depending on load and operating temperature, the lift control may respond
several times.
1.11.3
Safety Nut
In case of load nut failure the safety nut takes up the load and thus ensures safe
lowering of lift.
1.11.4
Load Nut Failure Protection
After load nut failure the carriages are locked in bottom position by the control
system. Lift operation will not be possible until the load nut has been replaced and
the control system has been reinitialized.
1.11.5
Load Nut Wear Check
The load nut can be visually checked for wear to have it replaced in time.
1.11.6
Overload Protection of Motors
The motors are equipped with overload protection switches.
1.11.7
Drive Belt Failure Protection
In case of drive belt failure the motors switch off immediately.
1.11.8
Pinch Point Protection
During lowering cycles the support arms automatically stop above bottom
position.
To lower the arms completely, the LOWER button must be released and pushed
again. Lift travel to the lower limit stop is accompanied by an audible signal.
1.11.9
Automatic Arm Restraint
The arm restraints are locked automatically once the lift is raised.
Pos: 3 0 /----- Form a t-----/M AN UE L LER UM BR UC H Se i ten um b ru ch @ 0\m od_1134403577687_0.docx @ 1277@ @ 1

9
BA361601-en
Pos: 3 1 / Techn ische Dokument atio n/Alle Geräte/Üb ersc hrift en/ Überschr ifte n 1/B/ Über schri ft 1: Bes chre ibun g @ 6\mod_1174482271453_75.docx@ 76889@ 1 @ 1
2
Description
Pos: 3 2 / Techn ische Dokument atio n/Alle Geräte/Üb ersc hrift en/ Überschr ifte n 1.1/ A/Über schr ift 1.1: All gemei nes @ 6\mod_1182865005781_75.docx@ 97736@ 2 @ 1
2.1
General Information
Pos: 3 3 / Techn ische Dokument atio n/Heb etech nik/3 6 Sä ulen-Hebebühnen/1601 ECONLIFT 6500/BA/Inhalt:3616Allgemeines@ 38\mod_1403691709571_75.docx @ 2043618@ @ 1
APOWER II 3.0/3.5/ BA/Inhalt: 36 40 Beschreibu ng Allgem eines (Text) @ 29\m od_1351077170134 _75.docx @ 16 67839 @ @ 1
These two-post lifts without base frame are equipped with an electronic
synchronisation system. Monitoring of
•synchroised operation
•load nut failure
•drive belt failure
using electronic components ensures a very high safety level.
Pos: 34 /Techn ische Dokument ation/Alle Ger äte/Übersc hrift en/ Überschr ifte n 1. 1/T/ Überschr ift 1.1: Te chnis che D aten @ 7\mod_1184075526343_75.docx @ 99711@ 2 @ 1
2.2
Specifications
Pos: 3 5 / Techn ische Dokument atio n/Heb etech nik/3 6 Säul en-Heb eb üh ne n /1 60 1 E CO N LI FT 65 00/ BA /I nh al t: 361 6 Te c hn isc h e Date n ( Tab e lle) @ 4 5\mod_1476255752058_75.docx@ 2589848@ @1
Fuse (time-delay) 35 A
Motor power per column 4 kW
Working temperature range 5…40 °C
Extension range of support arms max…min. 1880…860 mm
Concrete grade C 20/25
Drive-through width 2720 mm
Net weight/Shipping weight approx. 1430/1530 kg
Overall width 3750 mm
Overall width including motor cover 4170 mm
Overall height 5185 mm
Bottom clearance of support arms 160 mm
Lifting height max. 2110 mm
Full travel 1900 mm
Inside base plates 2815 mm
Noise emission < 70 dB(A)
Inside columns 3000 mm
Supply frequency 50 Hz
Supply voltage 400 V
Column height 2966 mm
Outside columns 3560 mm

10
BA361601-en
Load capacity 6500 kg
Adjustment range of support discs max…min. 175…130 mm
Pos: 3 6 / Techn ische Dokument atio n/Heb etech nik/3 6 Säul en-Heb ebüh ne n/ 1 601 E CON LI FT 6500/ BA /I nh alt: 3616 Techn isc he Daten Draufs ic ht ( B ild) @ 45\m od_1476193659682_0.docx @ 2589363@ @ 1
Pos: 3 7 /----- Form a t-----/M AN UE L LER UM BR UC H Se i ten um b ru ch @ 0\m od_1134403577687_0.docx@ 1277 @ @1

11
BA361601-en
Pos: 3 8 / Techn ische Dokument atio n/Heb etech nik/3 6 Säul en-Heb ebüh ne n/ 1 601 E CON LI FT 6500/ BA /I nh alt: 3616 Techn isc he Daten Fr on tans ic ht ( Bild ) @ 45\mod_1476193488473_0.docx @ 2589316@ @ 1
Pos: 3 9 /-----For m a t-----/M A N UE L LER UM BR UC H Se i ten um b ru ch @ 0\m od_1134403577687_0.docx @ 1277@ @ 1

12
BA361601-en
Pos: 4 0 / Techn ische Dokument atio n/Alle Geräte/Üb ersc hrift en/ Überschr ifte n 1/T/ Über schri ft 1: Transp ort und Lageru ng @2 0\mod_1268732488860_75.docx @ 826153@ 1 @ 1
3
Transport and Storage
Pos: 41 /Techn ische Dokume ntation/ Alle Geräte/ Inhalte/Inh alt: Transp ort und Lageru ng_12pt @ 26\mod_1324468980166_75.docx@ 1141285@ @ 1
Check package to ensure it is complete, in accordance with the order
confirmation. Report any transport damage to the carrier immediately.
During loading, unloading and transport always use suitable lifting equipment,
material handling equipment (e.g. cranes, forklifts, etc.) and the right load handling
attachments and slings. Always ensure that the parts to be transported are
suspended or loaded properly so that they cannot fall, taking into account size,
weight and the centre of gravity.
Store the packages in a covered area, protected from direct sunlight, at a low
humidity and with temperatures between 0...+40 °C (32…104 °F). Do not stack
packages.
When unpacking, take care to avoid any possibility of injury or damage. Keep at a
safe distance when opening the package strapping, do not allow any parts to fall
out.
Pos: 4 2 / Tec hn is ch e Dokument atio n/Alle Geräte/Üb ersc hrift en/ Überschr ifte n 1/M /Übers chr ift 1 : M ontag e und E rst inbe triebn ahme @ 18\mod_1255417443299_75.docx@ 463797@ 1 @ 1
4
Installation and Initial Operation
Pos: 4 3 / Techn ische Dokument atio n/Alle Geräte/I nhal te/Inh alt: M on tage u nd Ersti nbe tri eb na hme_ 12p t @ 26\mod_1324468562877_75.docx @ 1141153@ @ 1
Installation and initial operation of the equipment may be done only by authorized
and trained service technicians provided by the manufacturer, licensed dealers or
service partners.
Pos: 4 4 / Techn ische Dokument atio n/Alle Geräte/Üb ersc hrift en/ Überschr ifte n 1/B/ Über schri ft 1: Bed ie nung @ 6\mod_1174482271218_75.docx@ 76877 @1 @ 1
5
Operation
Pos: 4 5 / Techn ische Dokument atio n/Alle Geräte/Üb ersc hrift en/ Überschr ifte n 1.1/ H/Über schr ift 1 .1: H aup tschal ter @ 6\mod_ 11775 92858 312_7 5.do cx @ 90635 @ 2 @ 1
5.1
Main Switch
Pos: 4 6 / Techn ische Dokument atio n/Heb etech nik/0 0 HBZ Alle/In halte/In ha lt: H aup tschal ter m it N ot-Aus-Fu nkt ion H BZ _12p t @ 26\mod_1325575201603_75.docx@ 1144333 @ @ 1
The main switch is used as emergency switch. In case of emergency turn it to
position 0.
•Main switch in position 0: Power supply is interrupted
•Main switch in position 1: Lift is ready for operation
•When in position 0, the main switch can be protected against
tampering by means of a padlock.
Pos: 4 7 /----- Form a t-----/M AN UE L LER UM BR UC H Se i ten um b ru ch @ 0\m od_1134403577687_0.docx @ 1277@ @ 1

13
BA361601-en
Pos: 4 8 / Techn ische Dokument atio n/Alle Geräte/Üb ersc hrift en/ Überschr ifte n 1.1/ B/ Überschr ift 1. 1: Bed ien- u nd Anzei geelemen te @ 23\mod _1296 2203 01443_ 75.d ocx @ 9681 07 @ 2 @ 1
5.2
Controls and Indicators
Pos: 4 9 / Techn ische Dokument atio n/Heb etech nik/3 6 Sä ulen-H eb eb üh ne n/ 1 601 E C ON LI FT 6500/ BA/ I nh al t: 3 61 6 Bedie ne in he it U SH T 1( Bi ld) @ 46\m od_1481536171399_0.docx @ 2798138 @ @ 1
Pos: 5 0 / Techn ische Dokument atio n/Heb etech nik/3 6 Säul en-Heb ebüh ne n/ 1 601 E CONLI FT 65 00/BA/ Inhal t: 3616 B ediene inhe it USHT 1 ( Text) @ 46\m od_1481106900905_75.docx@ 2794544@ @ 1
A
Text display
D
(non-functional)
B
Menu
E
Raise
C
Confirm
F
Lower
Pos: 5 1 /----- Form a t-----/M AN UE L LER UM BR UC H Se i ten um b ru ch @ 0\m od_1134403577687_0.docx @ 1277@ @ 1
B
C
D
E
F
A

14
BA361601-en
Pos: 5 2 / Techn ische Dokument atio n/Alle Geräte/Üb ersc hrift en/ Überschr ifte n 1.1/ T/Üb erschr ift 1. 1: Te xtanz eige @ 45\mod_1472453476497_75.docx @ 2556978@ 2 @ 1
5.3
Text Display
Pos: 5 3 / Tec hn is ch e Dokument ation/H ebetech nik/36 S äulen-Heb eb ühne n/000 1 Säu len-Heb ebühnen All e/Inhalte/ Inhalt: 360 0 Textanzei ge USHT 1 - Norma ler Betrieb @ 46\mod_1481530261305_75.docx@ 2797838@ 3 @ 1
5.3.1
Normal Operation
Example texts
System status
Notes
[LIFT MODEL,
Version]
System self-test. An acoustic signal sounds.
H 875 mm
Lifting carriages are at rest. Lift
is ready for operation.
The mean value of the lifting
height of the carriages + A or +
B is displayed in millimetres.
H 925 mm
H 975 mm
…
Lifting carriages move upwards.
The period between the updates
of the text display is
approximately 1 s, which
corresponds to a change in
height of about 5 cm.
H 825 mm
H 775 mm
…
Lifting carriages move
downwards.
The period between the updates
of the text display is
approximately 1 s, which
corresponds to a change in
height of about 5 cm.
Emergency stop
Only with option “Second
operating unit“: The emergency
stop switch on the counter-post
has been pressed, the drive
motors are switched off.
The same acoustic signal
sounds as during the lowering
below the anti-squeeze
protectionheight. After turning
off the emergency switch the
control restarts.
Pos: 5 4 /----- Form a t-----/M AN UE L LER UM BR UC H Se i ten um b ru ch @ 0\m od_1134403577687_0.docx @ 1277@ @ 1

15
BA361601-en
Pos: 5 5 / Techn ische Dokument atio n/Heb etech nik/3 6 Säul en-Heb ebüh nen/ 0001 S äulen -Hebeb ühnen Alle/ Inhalte/I nhalt: 3600 Tex tanzei ge USHT 1 - Refere nzierung (20 17-03-10 11: 18 :0 9) @ 46\m od_1481530708938_75.docx@ 2797886@ 3 @ 1
5.3.2
Referenzierung
Example texts
System status
Notes
Reference Run
Operating data does not contain
a valid lifting height; a reference
run is required.
Operator must move the lifting
carriage to the lower end
position and confirm using the
Acknowledge button. “H 0 mm“
appears on the text display. If
the lifting carriages are not in
lower end position, confirmation
and completion of referencing is
not possible.
Caution: During referencing
cycles the current lifting height is
unknown! This process must be
performed without load!
Reference Run DN
Reference run of the lifting
carriages downwards ("down").
Referencing is performed in the
lower end position.
Pos: 5 6 / Techn ische Dokument atio n/Heb etech nik/3 6 Säul en-Heb ebüh nen/ 0001 S äulen -Hebeb ühne n Alle/ Inhal te/Inhal t: 3 600 Tex tanze ige USH T 1- F ehlerm eld ungen m it S erv icebed arf: E 00 0...E1 99 @ 4 6\mod_1481531068940_75.docx @ 2797934@ 3 @ 1
5.3.3
Error Messages with Service Requirement: E000…E199
Error codes in this range indicate errors during operation or control initialisation
which cannot be remedied by the operator. The control system tries to transfer
the machine into a safe state mode. Service required to make the lift ready for
operation again.
Example texts
System status
Notes
Error E101
Load nut failure at column +A. Contact service!
Error E102
Load nut failure at column +B. Contact service!
Error E105
Difference between carriages is
> 50 mm. Lift is transferred into
safe state mode.
Contact service!
Pos: 5 7 /----- Form a t-----/M AN UE L LER UM BR UC H Se i ten um b ru ch @ 0\m od_1134403577687_0.docx @ 1277@ @ 1

16
BA361601-en
Pos: 5 8 / Techn ische Dokument atio n/Heb etech nik/3 6 Säul en-Heb ebüh nen/ 0001 S äulen -Hebeb ühnen Alle/ Inhalte/I nhalt: 3600 Tex tanzei ge USHT 1 - Feh ler me ld un ge n : E 20 0. ..E 2 9 9 @ 46\mod_1481531980511_75.docx @ 27 98030 @ 3 @ 1
5.3.4
Error Messages: E200…E299
Error codes in this range indicate errors during control operation which typically do
not reappear after the lift has been restarted.
Example texts
System status
Notes
Button Error
Several buttons of the control
panel were presumably pressed
simultaneously.
Lift is transferred into a safe
state mode. After releasing the
buttons and a waiting period of
3 s the control is reinitialised.
Voltage Error
The supply voltage of the
assembly (UTarget= 24 V) is
outside the permissible range.
Switch off the lift and wait 15 s
before switching on again!
If an error reappears the power-
supplyof the lift has to be
checked by a specialist.
blocked +A
blocked +B
blocked
The control has detected a
blockage.
Raise/lower lift to unblock
support arms!
If the reference to post + A or +
B is missing, then either both
lifting carriages are blocked or
the location of the blockage is
unknown.
sinking +A
sinking +B
sinking
The control has detected an
automatic lowering.
If cause unknown – call service!
If the reference to column + A or
+ B is missing, then both lifting
carriages will lower.
Error E203
Lifting carriage +A is in lower
end position, but control
indicates at least 15 mm lifting
height ai column +A.
Possible cause of error:
Metallic object may be blocking
the sensor in the lower end
position at column +A or +B.
Removing the object and
restarting the control triggers a
follow-up referencing. The lift
can be moved downwards only.
The follow-up referencing must
be performed without load!
Error E204
Lifting carriage +B is in lower
end position, but control
indicates at least 15 mm lifting
height ai column +B.
Pos: 5 9 /----- Form a t-----/M AN UE L LER UM BR UC H Se i ten um b ru ch @ 0\m od_1134403577687_0.docx @ 1277@ @ 1

17
BA361601-en
Pos: 6 0 / Tec hn isch e Dokume nt at ion/ Al le Gerät e/Üb ers c hr iften/ Übe rs chri fte n 1.1/M /Üb ers c hr ift 1 .1 : Me nüf ühr u ng @ 46\m od_1479385748768_75.docx@ 2780926@ 2 @ 1
5.4
Menu Navigation
Pos: 6 1 / Tec hn is ch e Dokument atio n/Alle Geräte/Üb ersc hrift en/ Überschr ifte n 1. 1.1/Ü/ Übers chrift 1.1.1: Üb ersi cht @ 16\mod_1246353242165_75.docx @ 399194@ 3 @ 1
5.4.1
Exploded View
Pos: 6 2 / Techn ische Dokument atio n/Heb etech nik/3 6 Säul en-Heb ebüh ne n/ 1 601 E CON LI FT 6500/ BA /I nhalt: 3 616M enüf ührun g USHT 1 (Über sicht) @ 4 6\mod_1481109443715_75.docx@ 2794642@ @ 1
H 1234 mm
Operating mode/Rest mode
Menu 
ECONLIFT MENU
Lower Raise 
Automatic Stop
Confirm 
Menu
120 mm
Preselection in
intervals of 10 mm
with Raise/Lower
Lower Raise 
S/N Machine
Confirm 
Menu
123456-001
Lower Raise 
S/N ECU
Confirm 
Menu
001-123456789000
Lower Raise 
ECONLIFT MENU
Lower Raise 
Automatic Stop
Pos: 6 3 / Tec hn is ch e Dokument ation/H ebetech nik/36 S äulen-Heb ebüh nen/1 601 ECON LIFT 65 00/BA/ Inhalt: 3 616 Menü führun g USHT 1 (Men üpunkt e) @ 46\mod_1481110149865_75.docx @ 2794689@ 33333@ 1
5.4.2
Preselecting the Automatic Stop
Lift in operating mode/rest mode.
1 Press “Menu” once, then press “Lower”, until menu item “Automatic Stop”
appears.
2 Press “Confirm”.
3 Preselect required lifting height using “Raise/Lower” in intervals of 10 mm.
NOTE: Minimum height of automatic stop is 120 mm.
4 Press “Menu” once to quit the preselection. Press “Menu” again to go back to
the operating mode.
5.4.3
Disabling the Automatic Stop
Lift in operating mode/rest mode.
1 Press “Menu” once, then press “Lower”, until menu item “Automatic Stop”
appears.
2 Press “Confirm”.

18
BA361601-en
3 Use “Raise/Lower” to preselect a lifting height
below
the minimum height of the
automatic stop (120 mm) or
above
the maximum lifting height. Display “OFF”
appears.
4 Press “Menu” once to quit the preselection. Press “Menu” again to go back to
the operating mode.
5.4.4
Displaying the Serial Number of the Lift
Lift in operating mode/rest mode.
1 Press “Menu” once, then press “Lower”, until menu item “S/N Machine”
appears.
2 Press “Confirm”. Serial number is displayed.
3 Press “Menu” once to quit the preselection. Press “Menu” again to go back to
the operating mode.
5.4.5
Displaying the Serial Number of the Lift Control
Lift in operating mode/rest mode.
1 Press “Menu” once, then press “Lower”, until menu item “S/N ECU” appears.
2 Press “Confirm”. Serial number is displayed.
3 Press “Menu” once to quit the preselection. Press “Menu” again to go back to
the operating mode.
5.4.6
Displaying the Cloud ID
Lift in operating mode/rest mode.
1 Press “Menu” once, then press “Lower”, until menu item “Cloud ID” appears.
2 Press “Confirm”. Cloud ID is displayed.
3 Press “Menu” once to quit the preselection. Press “Menu” again to go back to
the operating mode.
Pos: 6 4 /----- Form a t-----/M AN UE L LER UM BR UC H Se i ten um b ru ch @ 0\m od_1134403577687_0.docx @ 1277@ @ 1

19
BA361601-en
Pos: 65 /Techn ische Dokument ation/Alle Ger äte/ Übersc hrift en/ Überschr ifte n 1. 1/T/ Überschr ift 1.1: Tra garm arret ierun g @ 9\mod_ 12101 6136 4709_ 75.d ocx @ 21210 7 @ 2 @ 1
5.5
Arm Restraint
Pos: 6 6 / Techn ische Dokument atio n/Heb etech nik/0 0 HBZ Alle/In halte/ Warnu ng!/ Inhalt : Warn ung - Ar retierhebe l_12pt @ 38\mod_1403765432254_75.docx@ 2044214@ @ 1
Never unlatch the arm restraint while the lift is loaded.
Pos: 6 7 / Techn ische Dokument atio n/Heb etech nik/3 6 Säul en-Heb eb üh ne n /1 60 1 E CO N LI FT 65 00/ BA /I nh al t: 361 6 Tr ag a rm ar r etier un g ( B ild ) @ 38\mod_1403766582198_0.docx@ 2044306@ @ 1
Pos: 6 8 / Techn ische Dokument atio n/Heb etech nik/3 6 Säul en-Heb eb üh ne n /1 60 1 E CO N LI FT 65 00/ BA /I nh al t: 361 6 Tr ag a rm ar r etier un g ( Te xt) @ 3 8\mod_1403765565010_75.docx@ 2044260@ @ 1
Each support arm is provided with an arm restraint which unlocks automatically
when the lift reaches bottom position.
When the carriages are in a raised position, the arm restraint can be disengaged
by pulling the restraint pin. Once the restraint pin is released, the arm restraint
locks automatically.
Pos: 6 9 /----- Form a t-----/M AN UE L LER UM BR UC H Se i ten um b ru ch @ 0\m od_1134403577687_0.docx @ 1277@ @ 1

20
BA361601-en
Pos: 7 0 / Techn ische Dokument atio n/Alle Geräte/Üb ersc hrift en/ Überschr ifte n 1.1/ V/Über sc hrift 1 .1: V orber eit ungen @ 8\mod_1204639543920_75.docx @ 155816@ 2 @ 1
5.6
Preparations
Pos: 7 1 / Techn ische Dokument atio n/Heb etech nik/3 6 Säul en-Heb ebüh nen/ 0001 S äulen -Hebeb ühne n Alle/ Inhal te/Inhal t: Vor berei tungen Säulen-H BZ_ 1 2pt @ 26\m od_1326281605536_75.docx@ 1152171@ @ 1
1 Fully lower the lift and swing the arms to full drive-through position.
2 Slowly position the vehicle midway between adapters. Apply the parking brake.
3 Swing and telescope arms as required to position adapters under vehicle
manufacturer's recommended lift points.
4 Turn the disc adapters in such a way that they evenly contact all four lift points.
5 Leave vehicle and remain clear of lift.
Pos: 7 2 / Techn ische Dokument atio n/Heb etech nik/3 6 Säul en-Heb eb üh ne n /2 60 1 E CO N I II / BA/ In h a lt : 36 26 Aufna hm e tel ler-E r h öh un g ( Tex t) @ 27\mod_1328091030599_75.docx@ 1536647@ @ 1
Extenders
The disk adapters can be raised in steps of 50 mm by using extenders. For fine
adjustment turn the disk adapters as required.
The extenders are optionally available in heights of 50, 100, 150 and 200 mm.
Use
ONE
extender only for each disk adapter.
Make sure the spring dowel sleeves lock into place.
Pos: 7 3 / Techn ische Dokument atio n/Heb etech nik/3 6 Säul en-Heb ebüh ne n/ 2 601 E CON III/ BA/I n ha lt: 3626 Au fna hm e tel ler-Erhöhung(Bilder)@ 11\mod_1230030932822_0.docx @ 288858@ @ 1
Pos: 7 4 /----- Form a t-----/M AN UE L LER UM BR UC H Se i ten um b ru ch @ 0\m od_1134403577687_0.docx @ 1277@ @ 1