Makita DC1801 User manual

High Capacity Battery Charger
~~
A.C. 120 V.
50 Hz ~ 60 Hz
MODEL DC1801
For Battery 7000, 7001, 7002, 7033, 7100, 7120, 9000
9001, 9002, 9033, 9100, 9101, 9102, 9120
9122, 9133, 1200, 1201, 1202, 1210, 1211
1220, 1222, 1233, 1422, 1433, 1822, 1833
9101A, 9102A, 12OlA, 1202A
INSTRUCTION MANUAL
D,C, 7,2 __ 18 189 mm x 105 mm x 78 mm 0.48 kg
(7-112"
x 4-1/8" x 3-1 /8") (1.06 Ibs)
SPEC I FICAT1 0 N S
I
Output I Dimensions (L x W x H) I Net weight
InDut

IMPORTANT SAFETY INSTRUCTIONS
Length of Cord (Feet)
AWG Size of Cord
I. SAVE THESE INSTRUCTIONS - This manual
25 50 100 150
18 18 18 16
contains important safety and operating instructions for battery charger.
2. Before usingbattery charger, read all instructions and cautionary markings
on
(1 1 battery charger, (2) battery, and (3) product using battery.
3. CAUTION - To reduce risk of injury, charge only MAKITA Battery.
Other types of batteries may burst causing personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold by the battery charger
manufacturermay result
in a risk of fire, electric shock, or injury topersons.
6. To reduce risk of damage toelectric plug and cord, pull by plug rather than
cord when disconnecting charger.
7. Make sure cord is located so that it will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary. Use of
improper extension cord could result in a risk of fire and electric shock.
If
extension cord must be used, make sure:
a. That pinsonplugof extension cordarethe same number, size, andshape
b. That extension cordisproperly wiredand
in goodelectricalcondition; and
c. That wire size is at least as large as the one specified in the table below.
TABLE
1
RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY CHARGERS
as those of plug on charger;
2

ADDITIONAL SAFETY RULES
FOR CHARGER
& BATTERY CARTRIDGE
1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF)
2. Do not attempttouse a step-uptransformer, an enginegenerator or DC power
3. Do not allow anything to cover the charger.
4. Always cover the battery terminals with the battery cover when the battery
5. A battery short can cause a large current flow, overheating, possible burns
or ABOVE 4OoC (104OF).
receptacle.
cartridge is not used.
and even a breakdown.
(1 1 Do not touch the terminals with any conductive material.
(2) Avoidstoringbattery cartridge in a container with other metalobjects such
(3) Do not expose battery cartridge to water or rain.
ture may reach or exceed 5OoC (122OF).
completely worn out. The battery cartridge can explode
in a fire.
as nails, coins, etc.
6. Do not store the tool and Battery Cartridge in locations where the tempera-
7. Do not incinerate the Battery Cartridge even if it is severely damaged or is
SAVE THESE INSTRUCTIONS.
3

Charging
Your new battery cartridge is not charged.
You will needto charge
it before use. Use
the high capacity battery charger Model
DC1801to chargethe battery cartridge.
Plugthe high capacity battery charger into
the properAIC voltage source. The charg-
inglight will flash ingreen color.
*Insert the battery cartridge
so that the
plus and minus terminals on the battery
cartridge are on the same sides as their
-
respective markings on the high capacity battery charger. Insert the cartridge fully into
the port
so that it restson the charger portfloor.
When the battery cartridge is inserted, the charging light color will change from green to
redand chargingwill begin. The charging light will remain lit steadily during charging.
When charging is completed, the charging light color will changefrom red to green.
*The chargingtime is as follows:
Battery 7000, 71
00, 7120,9000,9100,9120, 1200, 121 0 and 1220:approx 40 minutes.
Battery 7001, 9001, 9101, 9101A, 1201, 1211and 1201A:approx. 50 minutes.
Battery 7002, 9002, 9102, 9102A, 9122, 1202, 1202A, 1222, 1422 and 1822: approx. 60
minutes.
Battery 7033, 9033, 9133, 1233, 1433and 1833:approx.65 minutes.
*After charging, unplug the chargerfrom the powersource.
CAUTION:
The high capacity battery charger Model DCI801 isfor charging Makita battery cartridge.
Never use it for other purposes or for other manufacturer’s batteries.
When you charge a new battery cartridge or a battery cartridge which has not been used
for
a long period of time, it may not accept a full charge. This is a normal conditionand
does not indicate
a problem. You can recharge the battery cartridge fully after discharging
it completely and recharging
a couple of times.
If you chargeabattery cartridge from ajust-operated tool or a battery cartridge which has
been left in
a location exposed to direct sunlight or heat for a long time, the charging light
may flash in redcolor.
If this occurs, wait for awhile. Chargingwill begin after the battery
cartridge cools. The battery cartridge will cool faster if you remove the battery cartridge
from the high capacity battery charger.
If the charging lightflashes alternately ingreen and red color, a problem exists and charg-
ing is not possible. The terminals on the charger or battery cartridge are clogged with
dust or the battery cartridge is worn out or damaged.
If you wish to chargetwo batterycartridges, allow 15 minutes betweenchargingson the
high capacity batterycharger.
4

MAINTENANCE
CAUTIO N:
Always be sure that the charger is unpluggedand the battery cartridge is removed before
attempting to perform inspection or maintenance.
To maintain product SAFETY and RELIABILITY,repairs, maintenanceor adjustment should
be performed by Makita Authorized or Factory Service Centers, always using Makita
replacement parts.
5

MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to
be free of defects from workmanshipand materials for the period of ONE YEAR from the date of
original purchase. Should any trouble develop during this one-year period, retum the COMPLETE
tool, freight prepaid, to one of Makita’s Factory or Authorized ServiceCenters. If inspectionshows
the trouble is caused by defective workmanship or material, Makita will repair (or at our option,
replace) without charge.
ThisWarranty does not apply where:
0 repairs have been made or attemptedby others:
0 repairs are required because of normal wear and tear:
0 The tool has been abused, misused or improperly maintained;
0 alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTALOR CON-
SEQUENTIAL DAMAGES FROM THE SALE OR USE OFTHE PRODUCT. THIS DISCLAIMER
APPLIES BOTH DURING AND AFTER THE TERM OF THISWARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED
WARRANTIES OF “MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE,”
AFTER THE ONE-YEAR TERM OFTHISWARRANTY.
This Warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. Some states do not allow the exclusion or limitation
of incidentalor consequential
damages,
so the above limitation or exclusion may not apply to you. Some states do not allow
limitation onhow long an implied warranty lasts,
so the above limitation may not apply to you.
Makita Corporation
3-11 -8, Sumiyoshi-cho,
Anjo, Aichi 446-8502
Japan
884191 - 065