Makita DTM50Z User manual

DTM40
DTM50
EN Cordless Multi Tool INSTRUCTION MANUAL 4
SV Batteridriven multifunktionell
maskin BRUKSANVISNING 10
NO Flerfunksjonsverktøy uten
ledning BRUKSANVISNING 16
FI Akkukäyttöinen
monitoimityökalu KÄYTTÖOHJE 22
LV Bezvadu daudzfunkciju
darbarīks LIETOŠANAS INSTRUKCIJA 28
LT Akumuliatorinis
daugiafunkcis įrankis NAUDOJIMO INSTRUKCIJA 34
ET Juhtmeta universaaltööriist KASUTUSJUHEND 40
RU Аккумуляторный
Универсальный Резак
РУКОВОДСТВО ПО
ЭКСПЛУАТАЦИИ 46

1
2
3
1
1
2
1
1
1
1
1
3
2
Fig.1
Fig.2
Fig.3
Fig.4
Fig.5
Fig.6
Fig.7
Fig.8
2

12
3
1
2
3
4
1
1
2
3
4
5
6
7
9
8
Fig.14
Fig.15
Fig.9
Fig.10
Fig.11
Fig.12
Fig.13
3

4ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model DTM40 DTM50
Oscillation per minute 6,000 - 20,000 (min-1)
Oscillation angle, left/right 1.6 ° (3.2 ° total)
Overall length 307 - 324 mm
Net weight 1.7 - 2.0 kg 1.8 - 2.2 kg
Rated voltage D.C. 14.4 V D.C. 18 V
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsmaydifferfromcountrytocountry.
• Theweightmaydifferdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-
estcombination,accordingtoEPTA-Procedure01/2014,areshowninthetable.
Applicable battery cartridge and charger
Batterycartridge D.C.14.4 V Model BL1415N / BL1430 / BL1430B / BL1440 / BL1450 / BL1460B
D.C.18 V Model BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
Charger DC18RC/DC18RD/DC18RE/DC18SD/DC18SE/DC18SF
• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof
residence.
WARNING: Only use the battery cartridges and chargers listed above.Useofanyotherbatterycartridges
andchargersmaycauseinjuryand/orre.
Intended use
The tool is intended for sawing and cutting wood,
plastic,gypsum,non-ferrousmetals,andfastening
elements (e. g. unhardened nails and staples). It is also
intendedforworkingsoftwalltiles,aswellasdrysand-
ingandscrapingofsmallsurfaces.Itisespeciallyfor
workingclosetoedgeandushcutting.
Noise
ThetypicalA-weightednoiseleveldeterminedaccord-
ingtoEN62841:
Workmode:Sanding
Soundpressurelevel(LpA):78dB(A)
Uncertainty(K):3dB(A)
Thenoiselevelunderworkingmayexceed80dB(A).
Workmode:Cuttingwithplungecutsawblade
Model DTM40
Soundpressurelevel(LpA):82dB(A)
Soundpowerlevel(LWA):93dB(A)
Uncertainty(K):3dB(A)
Model DTM50
Soundpressurelevel(LpA):84dB(A)
Soundpowerlevel(LWA):95dB(A)
Uncertainty(K):3dB(A)
Workmode:Cuttingwithsegmentalsawblade
Soundpressurelevel(LpA):81dB(A)
Soundpowerlevel(LWA):92dB(A)
Uncertainty(K):3dB(A)
Workmode:Scraping
Model DTM40
Soundpressurelevel(LpA):81dB(A)
Soundpowerlevel(LWA):92dB(A)
Uncertainty(K):3dB(A)
Model DTM50
Soundpressurelevel(LpA):83dB(A)
Soundpowerlevel(LWA):94dB(A)
Uncertainty(K):3dB(A)
Wear ear protection
Vibration
Thevibrationtotalvalue(tri-axialvectorsum)deter-
minedaccordingtoEN62841:
Workmode:Sanding
Vibrationemission(ah):2.5m/s2or less
Uncertainty(K):1.5m/s2
Workmode:Cuttingwithplungecutsawblade
Model DTM40
Vibrationemission(ah):9.5m/s2
Uncertainty(K):1.5m/s2
Model DTM50
Vibrationemission(ah):10.0m/s2
Uncertainty(K):1.5m/s2
Workmode:Cuttingwithsegmentalsawblade
Model DTM40
Vibrationemission(ah):5.0m/s2
Uncertainty(K):1.5m/s2

5ENGLISH
Model DTM50
Vibrationemission(ah):5.5m/s2
Uncertainty(K):1.5m/s2
Workmode:Scraping
Model DTM40
Vibrationemission(ah):7.5m/s2
Uncertainty(K):1.5m/s2
Model DTM50
Vibrationemission(ah):9.5m/s2
Uncertainty(K):1.5m/s2
NOTE:Thedeclaredvibrationemissionvaluehas
beenmeasuredinaccordancewiththestandardtest
methodandmaybeusedforcomparingonetoolwith
another.
NOTE:Thedeclaredvibrationemissionvalue
mayalsobeusedinapreliminaryassessmentof
exposure.
WARNING:Thevibrationemissionduringactual
use of the power tool can differ from the declared
emissionvaluedependingonthewaysinwhichthe
tool is used.
WARNING:Besuretoidentifysafetymeasures
toprotecttheoperatorthatarebasedonanestima-
tionofexposureintheactualconditionsofuse(taking
accountofallpartsoftheoperatingcyclesuchas
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
TheECdeclarationofconformityisincludedasAnnexA
to this instruction manual.
General power tool safety warnings
WARNING: Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool.Failuretofollowallinstructions
listedbelowmayresultinelectricshock,reand/or
seriousinjury.
Save all warnings and instruc-
tions for future reference.
Theterm"powertool"inthewarningsreferstoyour
mains-operated(corded)powertoolorbattery-operated
(cordless) power tool.
CORDLESS MULTI TOOL SAFETY
WARNINGS
1. This power tool is intended to function for
sawing, cutting, grinding and sanding. Read all
safety warnings, instructions, illustrations and
specications provided with this power tool.
Failuretofollowallinstructionslistedbelowmay
resultinelectricshock,reand/orseriousinjury.
2.
Hold power tool by insulated gripping sur-
faces, when performing an operation where the
cutting accessory may contact hidden wiring.
Cuttingaccessorycontactinga"live"wiremay
makeexposedmetalpartsofthepowertool"live"
and could give the operator an electric shock.
3. Use clamps or another practical way to secure
and support the workpiece to a stable plat-
form.Holdingtheworkbyhandoragainstyour
bodyleavesitunstableandmayleadtolossof
control.
4. Always use safety glasses or goggles.
Ordinary eye or sun glasses are NOT safety
glasses.
5. Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
6. Hold the tool rmly.
7.
Make sure the application tool is not contacting
the workpiece before the switch is turned on.
8. Keep hands away from moving parts.
9. Do not leave the tool running. Operate the tool
only when hand-held.
10. Always switch off and wait for the blade to
come to a complete stop before removing the
blade from the workpiece.
11. Do not touch the application tool or the work-
piece immediately after operation; they may be
extremely hot and could burn your skin.
12. Do not operate the tool at no-load
unnecessarily.
13. Always use the correct dust mask/respirator
for the material and application you are work-
ing with.
14. Some material contains chemicals which may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follow material supplier
safety data.
15. This tool has not been waterproofed, so do not
use water on the workpiece surface.
16. Ventilate your work area adequately when you
perform sanding operations.
17. Use of this tool to sand some products, paints
and wood could expose user to dust contain-
ing hazardous substances. Use appropriate
respiratory protection.
18. Be sure that there are no cracks or breakage
on the pad before use. Cracks or breakage
may cause a personal injury.
19. Do not use accessories which are not speci-
cally designed and recommended by the tool
manufacturer.Justbecausetheaccessorycan
beattachedtoyourpowertool,itdoesnotassure
safe operation.
20. Wear personal protective equipment.
Depending on application, use face shield,
safety goggles or safety glasses. As appro-
priate, wear hearing protectors, gloves and
workshop apron capable of stopping small
abrasive or workpiece fragments.Theeyepro-
tectionmustbecapableofstoppingyingdebris
generatedbyvariousoperations.Thedustmask
orrespiratormustbecapableofltratingparticles
generatedbyyouroperation.Prolongedexposure
tohighintensitynoisemaycausehearingloss.

6ENGLISH
21. Keep bystanders a safe distance away from
work area. Anyone entering the work area
must wear personal protective equipment.
Fragmentsofworkpieceorofabrokenaccessory
mayyawayandcauseinjurybeyondimmediate
area of operation.
22. Never lay the power tool down until the acces-
sory has come to a complete stop. The spinning
accessorymaygrabthesurfaceandpullthe
powertooloutofyourcontrol.
23. Do not run the power tool while carrying it at
your side.Accidentalcontactwiththeaccessory
couldsnagyourclothing,pullingtheaccessory
intoyourbody.
24. Do not operate the power tool near ammable
materials.Sparkscouldignitethesematerials.
25. Do not use accessories that require liquid
coolants. Using water or other liquid coolants
mayresultinelectrocutionorshock.
26. Always be sure that the tool is switched off
and unplugged or that the battery cartridge is
removed before carrying out any work on the
tool.
27. Always be sure you have a rm footing. Be
sure no one is below when using the tool in
high locations.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or famil-
iarity with product (gained from repeated
use) replace strict adherence to safety
rules for the subject product. MISUSE or
failure to follow the safety rules stated in
this instruction manual may cause serious
personal injury.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
Forcommercialtransportse.g.bythirdparties,
forwarding agents, special requirement on pack-
agingandlabelingmustbeobserved.
Forpreparationoftheitembeingshipped,consult-
inganexpertforhazardousmaterialisrequired.
Pleasealsoobservepossiblymoredetailed
national regulations.
Tape or mask off open contacts and pack up the
batteryinsuchamannerthatitcannotmove
around in the packaging.
11. Follow your local regulations relating to dis-
posal of battery.
12. Use the batteries only with the products
specied by Makita.Installingthebatteriesto
non-compliantproductsmayresultinare,exces-
siveheat,explosion,orleakofelectrolyte.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Useofnon-genuineMakitabatteries,orbatteriesthat
havebeenaltered,mayresultinthebatterybursting
causingres,personalinjuryanddamage.Itwill
alsovoidtheMakitawarrantyfortheMakitatooland
charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4. Charge the battery cartridge if you do not use
it for a long period (more than six months).

7ENGLISH
FUNCTIONAL
DESCRIPTION
WARNING:
• Always be sure that the tool is switched
off and battery cartridge is removed before
adjusting or checking function on the tool.
Failuretoswitchoffandremovethebattery
cartridgemayresultinseriouspersonalinjury
from accidental start-up.
Installing or removing battery cartridge
►Fig.1: 1. Button 2. Red indicator 3.Batterycartridge
CAUTION:
• Alwaysswitchoffthetoolbeforeinstallingor
removingofthebatterycartridge.
• Hold the tool and the battery cartridge rmly
when installing or removing battery car-
tridge.Failuretoholdthetoolandthebattery
cartridgermlymaycausethemtoslipoffyour
hands and result in damage to the tool and
batterycartridgeandapersonalinjury.
Toremovethebatterycartridge,slideitfromthetool
whileslidingthebuttononthefrontofthecartridge.
Toinstallthebatterycartridge,alignthetongueonthe
batterycartridgewiththegrooveinthehousingandslip
itintoplace.Insertitallthewayuntilitlocksinplace
withalittleclick.Ifyoucanseetheredindicatoronthe
uppersideofthebutton,itisnotlockedcompletely.
CAUTION:
• Alwaysinstallthebatterycartridgefullyuntilthe
redindicatorcannotbeseen.Ifnot,itmayacci-
dentallyfalloutofthetool,causinginjurytoyou
orsomeonearoundyou.
• Donotinstallthebatterycartridgeforcibly.Ifthe
cartridgedoesnotslideineasily,itisnotbeing
insertedcorrectly.
Battery protection system (Lithium-
ion battery with star marking)
►Fig.2: 1.Starmarking
Lithium-ionbatterieswithastarmarkingareequipped
withaprotectionsystem.Thissystemautomatically
cutsoffpowertothetooltoextendbatterylife.
Thetoolwillautomaticallystopduringoperationifthetooland/
orbatteryareplacedunderoneofthefollowingconditions:
• Overloaded:
The tool is operated in a manner that causes
ittodrawanabnormallyhighcurrent.
In this situation, slide the slide switch on the
tooltowardthe"O(OFF)"positionandstop
theapplicationthatcausedthetooltobecome
overloaded. Then slide the slide switch toward
the "I (ON)" position again to restart.
Ifthetooldoesnotstart,thebatteryisover-
heated.Inthissituation,letthebatterycool
beforeslidingtheslideswitchtowardthe"I
(ON)" position again.
• Lowbatteryvoltage:
Theremainingbatterycapacityistoolow
and the tool will not operate. In this situation,
removeandrechargethebattery.
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
►Fig.3: 1. Indicator lamps 2.Checkbutton
Pressthecheckbuttononthebatterycartridgetoindi-
catetheremainingbatterycapacity.Theindicatorlamps
light up for a few seconds.
Indicator lamps Remaining
capacity
Lighted Off Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
Thebattery
mayhave
malfunctioned.
NOTE: Depending on the conditions of use and the
ambienttemperature,theindicationmaydifferslightly
fromtheactualcapacity.
Switch action
►Fig.4: 1.Slideswitch
CAUTION:
• Beforeinstallingthebatterycartridgeinto
thetool,alwayschecktoseethatthetoolis
switched off.
To start the tool, slide the slide switch toward the "I
(ON)" position.
To stop the tool, slide the slide switch toward the "O
(OFF)"position.
Adjusting the orbital stroke rate
►Fig.5: 1. Dial
Theorbitalstrokerateisadjustable.Tochangethe
orbitalstrokerate,turnthedialbetween1and6.The
higherthenumberis,thehighertheorbitalstroke
rateis.Presetthedialtothenumbersuitableforyour
workpiece.

8ENGLISH
NOTE:
• Thedialcannotbeturneddirectlyfrom1to6or
from6to1.Forcingthedialmaydamagethe
tool.Whenchangingthedialdirection,always
turn the dial moving it through each intermediate
number.
Lighting up the front lamp
WARNING:
• Neverlookintothelightdirectly.Directlight
causesdamagetoyoureyes.
►Fig.6: 1.Frontlamp
Slidetheslideswitchtowardthe"I(ON)"positiontolight
up the front lamp. The lamp keeps on lighting while the
switchisthe"I(ON)"position.Thelightautomaticallygoes
out after pressing the rear of the slide switch, and then
slidingtheslideswitchtowardthe"O(OFF)"position.
Overload protection
When the tool is overloaded and the tool temperature
reachesacertainlevel,thefrontlampblinksandthe
toolautomaticallystops.Removeacauseofoverload
to restart.
Indication lamp
►Fig.7: 1. Indication lamp
• Whentheremainingbatterycapacitygetslow,the
indicationlampblinks.
• Whentheremainingbatterycapacitygetsmuch
lower, the tool stops during operation and the
indicationlamplightsupabout10seconds.
Atthistime,removethebatterycartridgefromthetool
and charge it.
ASSEMBLY
CAUTION:
• Alwaysbesurethatthetoolisswitchedoffand
thebatterycartridgeisremovedbeforecarrying
outanyworkonthetool.
Installing or removing application
tool (optional accessory)
WARNING:
• Donotinstallapplicationtoolupsidedown.
Installingapplicationtoolupsidedownmay
damage the tool and cause serious personal
injury.
• Installattachmenttoolinthecorrectdirection
accordingtoyourwork.Applicationtoolcanbe
installedatanangleofevery30degree.
►Fig.8: 1.Applicationtoolinstallationbolt2. Holes
in the application tool 3.Protrusionsofthe
toolange
►Fig.9: 1.Applicationtoolinstallationbolt2.Hex
wrench 3. Tighten
Putanapplicationtool(optionalaccessory)onthetool
angesothattheprotrusionsofthetoolangetinthe
holes in the application tool and secure the application
toolbytighteningtheboltrmlywiththehexwrench.
When using sanding application tool, mount the appli-
cation tool on the sanding pad so that it matches the
sanding pad direction.
Thesandingpadhasahookandlooptypettingsys-
temwhichallowseasyandrapidttingofasanding
paper.
Assandingpapershaveholesfordustextraction,
mount a sanding paper so that the holes in a sanding
paper match those in the sanding pad.
To remove a sanding paper, raise its end and peel it off.
Loosenandremovetheapplicationtoolinstallationbolt
usingahexwrenchandthentakeofftheapplication
tool.
►Fig.10: 1.Applicationtoolinstallationbolt2. Holes
in the application tool 3.Adapter(required
for some application tools) 4.Protrusionsof
thetoolange
Whenusingapplicationtoolswithadifferenttypeof
installation section, use a correct adapter (optional
accessory).
Hex wrench storage
►Fig.11: 1.Hexwrench
Whennotinuse,storethehexwrenchasshowninthe
guretokeepitfrombeinglost.
OPERATION
WARNING:
• Beforestartingthetoolandduringoperation,
keepyourhandandfaceawayfromtheapplica-
tion tool.
CAUTION:
• Donotapplyexcessiveloadtothetoolwhich
maycauseamotorlockandstopthetool.
Cutting, sawing and scraping
CAUTION:
• Donotmoveonthetoolforciblyinthedirection
(eg. towards either side) of tool application with
nocuttingedge.Itmaydamagethetool.
►Fig.12
Puttheapplicationtoolontheworkpiece.
Andthenmovethetoolforwardsothattheapplication
tool movement does not slow down.
NOTE:
• Forcingorexcessivepressureonthetoolmay
reduceefciency.
• Beforecuttingoperation,itisrecommendedto
presettheorbitalstrokerate4-6.

9ENGLISH
Sanding
CAUTION:
• Donotreuseasandingpaperusedforsanding
metal to sand wood.
• Donotuseawornsandingpaperorsanding
paper without grit.
►Fig.13
Applyasandingpaperontheworkpiece.
NOTE:
• Usingatestmaterialsampletotryisrecom-
mendabletodetermineacorrectorbitalstroke
ratesuitableforyourwork.
• Useasandingpaperwiththesamegrituntil
sanding the whole workpiece is completed.
Replacing a sanding paper with different grit
sandingpapermaynotgetanenish.
Dust extraction attachment (optional
accessory)
►Fig.14: 1.Nozzleband2.Dustnozzle3.Dustnoz-
zle4. Dust attachment 5.Feltring6.Pad
7.Applicationtoolinstallationbolt8. Holes
in the tool 9.Protrusionsonthenozzleband
• Installdustnozzlesanddustattachment.
• Installthenozzlebandonthetoolsothatitspro-
trusionstintheholesinthetooltosecureit.
• Putthefeltringandthesandingpadonthedust
attachment and then secure them with the applica-
tiontoolinstallationbolt.
►Fig.15
Whenyouwishtoperformcleaneroperation,connect
avacuumcleanertoyourtool.Connectahoseofvac-
uumcleanertothedustextractionattachment(optional
accessory).
MAINTENANCE
CAUTION:
• Alwaysbesurethatthetoolisswitchedoffand
thebatterycartridgeisremovedbeforeattempt-
ing to perform inspection or maintenance.
• Neverusegasoline,benzine,thinner,alcohol
or the like. Discoloration, deformation or cracks
mayresult.
TomaintainproductSAFETYandRELIABILITY,
repairs,carbonbrushinspectionandreplacement,any
othermaintenanceoradjustmentshouldbeperformed
byMakitaAuthorizedServiceCenters,alwaysusing
Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
• Theseaccessoriesorattachmentsarerecom-
mendedforusewithyourMakitatoolspecied
inthismanual.Theuseofanyotheraccessories
orattachmentsmightpresentariskofinjuryto
persons.Onlyuseaccessoryorattachmentfor
its stated purpose.
Ifyouneedanyassistanceformoredetailsregard-
ingtheseaccessories,askyourlocalMakitaService
Center.
• Segmentsawblade
• Roundsawblade
• Plungecutsawblade
• Scraper(rigid)
• Scraper(exible)
• Serratedsegblade
• Generaljointcutter
• HMremover
• HMsegsawblade
• HMsandingplate
• Diamondsegsawblade
• Sandingpad
• Adapter
• Abrasivepaperdelta(red/white/black)
• Fleecedelta(medium/coarse/withoutgrit)
• Polishingfeltdelta
• Hexwrench
• Dustextractionattachment
• Makitagenuinebatteryandcharger
NOTE:
• Someitemsinthelistmaybeincludedinthe
toolpackageasstandardaccessories.They
maydifferfromcountrytocountry.

10 SVENSKA
SVENSKA (Originalinstruktioner)
SPECIFIKATIONER
Modell DTM40 DTM50
Svängningarperminut 6 000 - 20 000 (min-1)
Oscillationsvinkel,vänster/höger 1,6 ° (totalt 3,2 °)
Totallängd 307 - 324 mm
Vikt 1,7 - 2,0 kg 1,8 - 2,2 kg
Märkspänning 14,4Vlikström 18Vlikström
• Pågrundavvårtpågåendeprogramförforskningochutvecklingkandessaspecikationerändrasutanföregå-
ende meddelande.
• Specikationerkanvarieramellanolikaländer.
• Viktenkanvarieraberoendepåtillbehören,inklusivebatterikassett.Denlättasteochdentyngstakombinatio-
nenenligtEPTA-procedur01/2014visasitabellen.
Tillgänglig batterikassett och laddare
Batterikassett 14,4Vlikströmsmodell BL1415N / BL1430 / BL1430B / BL1440 / BL1450 / BL1460B
18Vlikströmsmodell BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
Laddare DC18RC/DC18RD/DC18RE/DC18SD/DC18SE/DC18SF
• Vissaavbatterikassetternaochladdarnapålistanovankanskeintennstillgängligaidinregion.
VARNING: Använd endast batterikassetter och laddare från listan ovan.Användningavandrabatterikas-
setterochladdarekanorsakapersonskadaoch/ellerbrand.
Avsedd användning
Maskinenäravseddförsågningochkapningiträ,plast,
gips,ickejärnmetallerochfästdelar(t.ex.ohärdadspik
ochhäftklamrar).Denärocksåavseddföranvändning
påmjuktväggkakelförtorrslipningochskrapningav
småytor.Denärspecielltavseddförattarbetaihörn
ochförslätkapning.
Buller
TypiskaA-vägdabullernivånärmättenligtEN62841:
Arbetsläge:Slipning
Ljudtrycksnivå(LpA):78dB(A)
Mättolerans(K):3dB(A)
Bullernivånvidarbetekanöverstiga80dB(A).
Arbetsläge:Kapameddyksågblad
Modell DTM40
Ljudtrycksnivå(LpA):82dB(A)
Ljudeffektnivå(LWA):93dB(A)
Mättolerans(K):3dB(A)
Modell DTM50
Ljudtrycksnivå(LpA):84dB(A)
Ljudeffektnivå(LWA):95dB(A)
Mättolerans(K):3dB(A)
Arbetsläge:Kapamedsegmentsågblad
Ljudtrycksnivå(LpA):81dB(A)
Ljudeffektnivå(LWA):92dB(A)
Mättolerans(K):3dB(A)
Arbetsläge:Skrapning
Modell DTM40
Ljudtrycksnivå(LpA):81dB(A)
Ljudeffektnivå(LWA):92dB(A)
Mättolerans(K):3dB(A)
Modell DTM50
Ljudtrycksnivå(LpA):83dB(A)
Ljudeffektnivå(LWA):94dB(A)
Mättolerans(K):3dB(A)
Använd hörselskydd
Vibration
Vibrationenstotalvärde(tre-axlarsvektorsumma)mätt
enligtEN62841:
Arbetsläge:Slipning
Vibrationsemission(ah):2,5m/s2ellerlägre
Mättolerans(K):1,5m/s2
Arbetsläge:Kapameddyksågblad
Modell DTM40
Vibrationsemission(ah):9,5m/s2
Mättolerans(K):1,5m/s2
Modell DTM50
Vibrationsemission(ah):10,0m/s2
Mättolerans(K):1,5m/s2
Arbetsläge:Kapamedsegmentsågblad
Modell DTM40
Vibrationsemission(ah):5,0m/s2
Mättolerans(K):1,5m/s2