Makita DUX60 User manual

DUX60
EN Cordless Multi Function
Power Head INSTRUCTION MANUAL 5
SL Brezžična večfunkcijska
pogonska glava NAVODILA ZA UPORABO 15
SQ Kokë elektrike me shumë
funksione pa kordon MANUALI I PËRDORIMIT 25
BG
Многофункционална
задвижваща глава без кабел
РЪКОВОДСТВО ЗА
ЕКСПЛОАТАЦИЯ 35
HR Bežična višefunkcijska
električna glava PRIRUČNIK S UPUTAMA 46
МК
Безжична повеќефункционална
глава за напојување
УПАТСТВО ЗА УПОТРЕБА 56
SR Бежична вишенаменска
погонска глава УПУТСТВО ЗА УПОТРЕБУ 66
RO
Cap cu motor universal fără cablu MANUAL DE INSTRUCŢIUNI 76
UK
Акумуляторний
багатофункціональний
приводний інструмент
ІНСТРУКЦІЯ З
ЕКСПЛУАТАЦІЇ 86
RU
Многофункциональный
аккумуляторный привод
для садовых насадок
РУКОВОДСТВО ПО
ЭКСПЛУАТАЦИИ 97

2
1
89
10 11
3
4
5
6
7
12
Fig.1
2
1
3
Fig.2
1
2
Fig.3
1
Fig.4
2
1
Fig.5
1
Fig.6
1
Fig.7
2

4
2
3
1
3
5
Fig.8
1
2
Fig.9
1
Fig.10
1
2
3
Fig.11
1
Fig.12
Fig.12
3
1
2
Fig.13
1
2
Fig.14
21
Fig.15
3

1
2
Fig.16
1
Fig.17
1
2
Fig.18
1
Fig.19
4

5ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model: DUX60
No load speed
(without attachment)
Low 0 - 5,700 min-1
Medium 0 - 8,200 min-1
High 0 - 9,700 min-1
Overall length 1,011 mm
Rated voltage D.C. 36 V
Net weight 5.1 kg - 11.7 kg
• Due to our continuing program of research and development, the specications herein are subject to change without notice.
• Specications may di󰀨er from country to country.
• The weight may di󰀨er depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B
Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
DC18SH
• Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or re.
Recommended cord connected power source
Cord connected battery pack BL36120A
Portable power pack PDC01 / PDC1200
• The cord connected power source(s) listed above may not be available depending on your region of residence.
• Before using the cord connected power source, read instruction and cautionary markings on them.
No load speed with attachment
Model Rotation speed
Low Medium High
EM401MP 0 - 4,200 min-1 0 - 6,000 min-1 0 - 7,100 min-1
EM404MP / EM406MP 0 - 3,500 min-1 0 - 5,000 min-1 0 - 6,000 min-1
EM407MP Upper blade 0 - 220 min-1 0 - 310 min-1 0 - 370 min-1
Lower blade 0 - 470 min-1 0 - 670 min-1 0 - 790 min-1
EM408MP / EM409MP 0 - 4,200 min-1 0 - 6,000 min-1 0 - 7,100 min-1
EN401MP / EN410MP / EN420MP
(Strokes per minute)
0 - 2,400 min-1 0 - 3,400 min-1 0 - 4,000 min-1
EY401MP (chain speed) 0 - 12 m/s 0 - 17 m/s 0 - 20 m/s
EY403MP (chain speed) 0 - 11 m/s 0 - 16 m/s 0 - 19 m/s
KR400MP 0 - 160 min-1 0 - 230 min-1 0 - 280 min-1
KR401MP 0 - 130 min-1 0 - 190 min-1 0 - 230 min-1
EE400MP 0 - 2,800 min-1 0 - 4,000 min-1 0 - 4,700 min-1
EJ400MP 0 - 1,600 min-1 0 - 2,300 min-1 0 - 2,800 min-1
BR400MP 0 - 130 min-1 0 - 190 min-1 0 - 230 min-1
SW400MP 0 - 130 min-1 0 - 190 min-1 0 - 230 min-1
UB400MP 0 - 5,700 min-1 0 - 7,850 min-1 0 - 8,250 min-1
UB401MP 0 - 5,700 min-1 0 - 7,850 min-1 0 - 8,250 min-1

6ENGLISH
Approved attachment
Type Model
Brushcutter attachment EM401MP / EM404MP
String trimmer attachment EM406MP
Rotary scissors attachment EM407MP
Grass trimmer attachment EM408MP / EM409MP
Hedge trimmer attachment EN401MP / EN410MP
Ground trimmer attachment EN420MP
Pole saw attachment EY401MP / EY403MP
Cultivator attachment KR400MP / KR401MP
Edger attachment EE400MP
Co󰀨ee harvester attachment EJ400MP
Shaft extension attachment LE400MP
Power brush attachment BR400MP
Power sweep attachment SW400MP
Blower attachment UB400MP / UB401MP
Symbols
The followings show the symbols which may be used
for the equipment. Be sure that you understand their
meaning before use.
Read instruction manual.
Take particular care and attention.
Do not expose to moisture.
Ni-MH
Li-ion
Only for EU countries
Due to the presence of hazardous com-
ponents in the equipment, waste electrical
and electronic equipment, accumulators
and batteries may have a negative impact
on the environment and human health.
Do not dispose of electrical and electronic
appliances or batteries with household
waste!
In accordance with the European Directive
on waste electrical and electronic equip-
ment and on accumulators and batteries
and waste accumulators and batteries,
as well as their adaptation to national law,
waste electrical equipment, batteries and
accumulators should be stored separately
and delivered to a separate collection point
for municipal waste, operating in accor-
dance with the regulations on environmen-
tal protection.
This is indicated by the symbol of the
crossed-out wheeled bin placed on the
equipment.
Intended use
This cordless multi function power head is intended for
driving an approved attachment listed in the section
"SPECIFICATIONS" of this instruction manual. Never
use the unit for the other purpose.
WARNING: Read the instruction manual of
the attachment as well as this instruction manual
before using. Failure to follow the warnings and
instructions may result serious injury.

7ENGLISH
Noise
Attachment Sound pressure level
average Sound power level average Applicable standard
LpA (dB (A))
Uncertainty K
(dB (A))
LWA (dB (A)) Uncertainty K
(dB (A))
EM401MP (as a brushcutter) 78.5 1.0 90.2 1.5 EN11806
EM401MP
(as a string trimmer)
Nylon cutting head 84.3 0.6 93.3 1.6
EN50636-2-91
Plastic blade 77.0 1.7 88.5 1.8 EN50636-2-91
EM404MP (as a brushcutter) 82.5 2.2 93.3 2.9 EN11806
EM404MP
(as a string trimmer)
Nylon cutting head 84.7 2.3 92.8 1.6
EN50636-2-91
Plastic blade 76.0 1.8 87.7 1.5 EN50636-2-91
EM406MP Nylon cutting head 84.7 2.5 93.5 2.2 EN50636-2-91
Plastic blade 77.0 1.9 85.6 2.0 EN50636-2-91
EM407MP 83.2 3.9 99.3 2.5 ISO22868
(ISO11806-1)
EM408MP (as a brushcutter) 79.9 2.6 94.5 2.0 ISO22868
(ISO11806-1)
EM408MP
(as a string trimmer)
Nylon cutting head 79.0 2.6 91.8 1.7 ISO22868
(ISO11806-1)/
EN50636-2-91
Plastic blade 80.1 0.7 91.0 1.6 ISO22868
(ISO11806-1)/
EN50636-2-91
EM409MP Nylon cutting head 79.9 2.3 92.7 0.9 ISO22868
(ISO11806-1)/
EN50636-2-91
Plastic blade 80.3 0.9 91.2 2.2 ISO22868
(ISO11806-1)/
EN50636-2-91
EN401MP 82 393 3 EN62841-4-2
EN401MP + LE400MP 82 393 3 EN62841-4-2
EN410MP 77 388 3 EN62841-4-2
EN410MP + LE400MP 77 388 3 EN62841-4-2
EN420MP 83 394 3 EN62841-4-2
EY401MP 92.5 1.4 101.9 1.4 ISO11680-1
EY401MP + LE400MP 86.6 1.0 101.2 1.0 ISO11680-1
EY403MP 96 3105 3
ISO22868
(ISO11680-1)
EY403MP+LE400MP 96 3105 3 ISO22868
(ISO11680-1)
KR400MP 76.7 2.2 84.2 1.0 EN709
KR401MP 73.1 1.4 84.2 1.8 EN709
EE400MP 74.8 1.5 88.2 2.6 ISO11789
EJ400MP 87.4 1.4 94.5 1.3 ISO10517
EJ400MP + LE400MP 85.6 1.0 95.5 1.3 ISO10517
BR400MP 79.5 0.9 89.0 0.7
EN60335-2-72
SW400MP 80.1 1.8 88.8 0.7 EN60335-2-72
UB400MP 89.8 0.4 100.4 0.8 EN50636-2-100
UB401MP 83.4 1.1 94.1 0.8 EN50636-2-100
• Even if the sound pressure level listed above is 80 dB (A) or less, the level under working may exceed 80 dB
(A). Wear ear protection.
NOTE: The declared noise emission value(s) has been measured in accordance with a standard test method and
may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may also be used in a preliminary assessment of exposure.

8ENGLISH
Vibration
Attachment Left handle (Front grip) Right handle (Rear grip) Applicable
standard
ah (m/s2)
Uncertainty K
(m/s2)
ah (m/s2) Uncertainty K
(m/s2)
EM401MP (as a brushcutter) 3.0 1.5 2.5 1.5 EN11806
EM401MP
(as a string trimmer)
Nylon cutting head 5.0 1.5 2.5 1.5
EN50636-2-91
Plastic blade 2.5 1.5 2.5 1.5 EN50636-2-91
EM404MP (as a brushcutter) 3.0 1.5 2.5 1.5 EN11806
EM404MP
(as a string trimmer)
Nylon cutting head 3.0 1.5 2.5 1.5
EN50636-2-91
Plastic blade 2.5 1.5 2.5 1.5 EN50636-2-91
EM406MP Nylon cutting head 2.5 1.5 2.5 1.5 EN50636-2-91
Plastic blade 4.0 1.5 2.5 1.5 EN50636-2-91
EM407MP 2.5 1.5 2.5 1.5 ISO22867
(ISO11806-1)
EM408MP (as a brushcutter) 2.5 1.5 2.5 1.5 ISO22867
(ISO11806-1)
EM408MP
(as a string trimmer)
Nylon cutting head 2.5 1.5 2.5 1.5 ISO22867
(ISO11806-1)
Plastic blade 2.5 1.5 2.5 1.5 ISO22867
(ISO11806-1)
EM409MP Nylon cutting head 2.5 1.5 2.5 1.5 ISO22867
(ISO11806-1)
Plastic blade 2.5 1.5 2.5 1.5 ISO22867
(ISO11806-1)
EN401MP 5.5 1.5 3.5 1.5 EN62841-4-2
EN401MP + LE400MP 5.5 1.5 4.0 1.5 EN62841-4-2
EN410MP 4.0 1.5 2.5 1.5 EN62841-4-2
EN410MP + LE400MP 4.5 1.5 2.5 1.5 EN62841-4-2
EN420MP 6.5 1.5 4.0 1.5 EN62841-4-2
EY401MP 2.5 1.5 2.5 1.5 ISO11680-1
EY401MP + LE400MP 5.5 1.5 2.5 1.5 ISO11680-1
EY403MP 2.7 1.5 2.5 1.5
ISO22867
(ISO11680-1)
EY403MP+LE400MP 3.0 1.5 2.5 1.5 ISO22867
(ISO11680-1)
KR400MP 2.5 1.5 2.5 1.5 EN709
KR401MP 2.5 1.5 2.5 1.5 EN709
EE400MP 2.5 1.5 2.5 1.5 ISO11789
EJ400MP 4.0 1.5 3.0 1.5 ISO10517
EJ400MP + LE400MP 4.5 1.5 3.0 1.5 ISO10517
BR400MP 2.5 1.5 2.5 1.5
EN60335-2-72
SW400MP 2.6 1.5 2.6 1.5 EN60335-2-72
UB400MP 4.5 2.0 2.5 1.5 EN50636-2-100
UB401MP 3.6 1.7 2.5 1.5 EN50636-2-100
NOTE: The declared vibration total value(s) has been measured in accordance with a standard test method and
may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also be used in a preliminary assessment of exposure.

9ENGLISH
WARNING: The vibration emission during actual use of the power tool can di󰀨er from the declared
value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.
WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation
of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the
times when the tool is switched o󰀨 and when it is running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, re and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using battery.
2. Do not disassemble or tamper with the battery
cartridge. It may result in a re, excessive heat,
or explosion.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdown.
6. Do not store and use the tool and battery car-
tridge in locations where the temperature may
reach or exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the
battery cartridge. Such conduct may result in a
re, excessive heat, or explosion.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Please also observe possibly more detailed
national regulations.
Tape or mask o󰀨 open contacts and pack up the
battery in such a manner that it cannot move
around in the packaging.
11. When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specied by Makita. Installing the batteries to
non-compliant products may result in a re, exces-
sive heat, explosion, or leak of electrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
14. During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool imme-
diately after use as it may get hot enough to
cause burns.
16. Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge. It may result in poor performance or
breakdown of the tool or battery cartridge.
17. Unless the tool supports the use near
high-voltage electrical power lines, do not use
the battery cartridge near high-voltage electri-
cal power lines. It may result in a malfunction or
breakdown of the tool or battery cartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing res, personal injury and damage. It will
also void the Makita warranty for the Makita tool and
charger.

10 ENGLISH
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely dis-
charged. Always stop tool operation and charge the
battery cartridge when you notice less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4. When not using the battery cartridge, remove
it from the tool or the charger.
5. Charge the battery cartridge if you do not use
it for a long period (more than six months).
PARTS DESCRIPTION
► Fig.1
1Battery cartridge 2Lock-o󰀨 lever 3Switch trigger 4Hanger
5Handle 6Release button 7Barrier (country specic) 8Speed indicator
9Power lamp 10 Main power button 11 Reverse button 12 Shoulder harness
FUNCTIONAL
DESCRIPTION
WARNING: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before adjusting or checking function on the tool.
Failure to switch o󰀨 and remove the battery cartridge
may result in serious personal injury from accidental
start-up.
Installing or removing battery
cartridge
CAUTION: Always switch o󰀨 the tool before
installing or removing of the battery cartridge.
CAUTION: Hold the tool and the battery car-
tridge rmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge rmly may cause them to slip o󰀨 your hands
and result in damage to the tool and battery cartridge
and a personal injury.
► Fig.2: 1. Red indicator 2. Button 3. Battery cartridge
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator as
shown in the gure, it is not locked completely.
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
CAUTION: Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
Tool / battery protection system
The tool is equipped with a tool/battery protection sys-
tem. This system automatically cuts o󰀨 power to the
motor to extend tool and battery life. The tool will auto-
matically stop during operation if the tool or battery is
placed under one of the following conditions:
Status Indicator lamps
On O󰀨 Blinking
Overload
Overheat
Over
discharge
Overload protection
If the tool is overloaded by entangled weeds or other
debris, and the middle indicators start blinking and
the tool automatically stops.
In this situation, turn the tool o󰀨 and stop the application
that caused the tool to become overloaded. Then turn
the tool on to restart.
Overheat protection for tool or
battery
When a over heating occurs, all speed indicators blink.
If the overheating occurs, the tool stops automatically.
Let the tool and/or battery cool down before turning the
tool on again.

11 ENGLISH
Overdischarge protection
When the battery capacity becomes low, the tool stops
automatically and indicator blinks.
If the tool does not operate even when the switches are
operated, remove the batteries from the tool and charge
the batteries.
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
► Fig.3: 1. Indicator lamps 2. Check button
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for a few seconds.
Indicator lamps Remaining
capacity
Lighted O󰀨 Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
The battery
may have
malfunctioned.
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may di󰀨er slightly
from the actual capacity.
NOTE: The rst (far left) indicator lamp will blink when
the battery protection system works.
Main power switch
WARNING: Always turn o󰀨 the main power
switch when not in use.
To stand by the tool, press the main power button until
the main power lamp lights up. To turn o󰀨, press the
main power button again.
► Fig.4: 1. Main power button
NOTE: The main power lamp brinks if the switch
trigger is pulled under unoperatable conditions. The
lamp blinks if you turn on the main power switch while
holding down the lock-o󰀨 lever and the switch trigger.
NOTE: This tool employs the auto power-o󰀨 function.
To avoid unintentional start up, the main power switch
will automatically shut down when the switch trigger
is not pulled for a certain period after the main power
switch is turned on.
Switch action
WARNING: For your safety, this tool is
equipped with lock-o󰀨 lever which prevents the
tool from unintended starting. NEVER use the tool
if it runs when you simply pull the switch trigger
without pressing the lock-o󰀨 lever. Return the
tool to our authorized service center for proper
repairs BEFORE further usage.
WARNING: NEVER tape down or defeat pur-
pose and function of lock-o󰀨 lever.
CAUTION: Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
NOTICE: Do not pull the switch trigger hard with-
out pressing the lock-o󰀨 lever. This can cause
switch breakage.
To prevent the switch trigger from being accidentally
pulled, a lock-o󰀨 lever is provided.
► Fig.5: 1. Lock-o󰀨 lever 2. Switch trigger
To start the tool, turn on the main power switch and
grasp the handle (the lock-o󰀨 lever is released by the
grasp) and then pull the switch trigger. Tool speed is
increased by increasing the pressure on the switch
trigger. To stop the tool, release the switch trigger.
Speed adjusting
You can adjust the tool speed by tapping the main
power button.
Each time you tap the main power button, the level of
speed will change.
► Fig.6: 1. Main power button
Indicator Mode
High
Medium
Low

12 ENGLISH
Reverse button for debris removal
WARNING: Switch o󰀨 the tool and remove
the battery cartridge before you remove entan-
gled weeds or debris which the reverse rotation
function can not remove. Failure to switch o󰀨 and
remove the battery cartridge may result in serious
personal injury from accidental start-up.
This tool has a reverse button to change the direction of rotation.
It is only for removing weeds and debris entangled in the tool.
To reverse the rotation, tap the reverse button and pull
the trigger when the tool’s head is stopped. The power
lamp starts blinking, and the tool's head rotates in
reverse direction when you pull the switch trigger.
To return to regular rotation, release the trigger and wait
until the tool's head stops.
► Fig.7: 1. Reverse button
NOTE:
During the reverse rotation, the tool operates only
for a short period of time and then automatically stops.
NOTE: Once the tool is stopped, the rotation returns
to regular direction when you start the tool again.
NOTE: If you tap the reverse button while the tool's
head is still rotating, the tool comes to stop and to be
ready for reverse rotation.
Electronic torque control function
The tool electronically detects a sudden drop in the rotation
speed which may cause a kickback. In this situation, the tool
automatically stops to prevent further rotation of cutting tool.
To restart the tool, release the switch trigger. Clear the cause
of sudden drop in the rotation speed and then turn the tool on.
NOTE: This function is not a preventive measure for
kickbacks.
ASSEMBLY
WARNING: Always be sure that the tool is
switched o󰀨 and battery cartridge is removed
before carrying out any work on the tool. Failure to
switch o󰀨 and remove the battery cartridge may result
in serious personal injury from accidental start-up.
WARNING: Never start the tool unless it is
completely assembled. Operation of the tool in a
partially assembled state may result in serious per-
sonal injury from accidental start-up.
Mounting the handle
Attach the handle with supplied clamps and bolts. Make
sure that the handle is located between the spacer and
the arrow mark. Do not remove or shrink the spacer.
► Fig.8: 1. Handle 2. Hex socket bolt 3. Clamp
4. Spacer 5. Arrow mark
Attach the barrier (country specic) to the handle using
the screw on the barrier. Once assembled, do not
remove the barrier.
► Fig.9: 1. Barrier 2. Screw
Mounting the attachment pipe
CAUTION: Always check that the attachment
pipe is secured after installation. Improper instal-
lation may cause the attachment falling o󰀨 from the
power unit and cause personal injury.
Mount the attachment pipe to the power unit.
1.
Turn the lever of the power unit toward the attachment side.
► Fig.10: 1. Lever
2. Remove the cap of the attachment. Align the pin
with the arrow mark and insert the attachment pipe until
the release button pops up.
► Fig.11: 1. Release button 2. Arrow mark 3. Pin
3. Turn the lever toward the power unit side.
► Fig.12: 1. Lever
Make sure that the surface of the lever is parallel to the pipe.
To remove the pipe, turn the lever toward the attach-
ment side and pull the pipe out while pressing down the
release button.
► Fig.13: 1. Release button 2. Lever 3. Pipe
Adjusting the handle/hanger position
Adjust the handle and hanger position to obtain confort-
able handling of the tool.
Loosen the hex socket head bolt on the handle. Move
the handle to a comfortable working position and then
tighten the bolt.
► Fig.14: 1. Handle 2. Hex socket head bolt
Loosen the hex socket head bolt on the hanger. Move
the hanger to a comfortable working position and then
tighten the bolt.
► Fig.15: 1. Hex socket head bolt 2. Hanger
Attaching shoulder harness
WARNING: Be extremely careful to maintain
control of the tool at all times. Do not allow the
tool to be deected toward you or anyone in the
work vicinity. Failure to keep control of the tool
could result in serious injury to the bystander and the
operator.
CAUTION: Always use the shoulder harness
attached. Before operation, adjust the shoulder
harness according to the user size to prevent
fatigue.
CAUTION: When you use the tool in combi-
nation of the backpack-type power supply such
as portable power pack, do not use the shoulder
harness included in the tool package, but use the
hanging band recommended by Makita.
If you put on the shoulder harness included in the
tool package and the shoulder harness of the back-
pack-type power supply at the same time, removing
the tool or backpack-type power supply is di󰀩cult in
case of an emergency, and it may cause an accident
or injury. For the recommended hanging band, ask
Makita Authorized Service Centers.

13 ENGLISH
Put the shoulder harness on your left shoulder by put-
ting your head and right arm through it. Keep the tool on
your right side.
After putting the shoulder harness, attach it to the tool
by connecting the buckles provided on both the tool
hook and the harness. Be sure that the buckles click
and lock completely in place.
Adjust the strap to the suitable length for your operation.
► Fig.16: 1. Hanger 2. Hook
The buckle is provided with a means of quick release
which can be accomplished by simply squeezing the
sides and the buckle.
► Fig.17: 1. Buckle
Hex wrench storage
CAUTION: Be careful not to leave the hex
wrench inserted in the tool head. It may cause
injury and/or damage to the tool.
When not in use, store the hex wrench as illustrated to
keep it from being lost.
► Fig.18: 1. Handle 2. Hex wrench
MAINTENANCE
WARNING: Always be sure that the tool is
switched o󰀨 and battery cartridge is removed
before attempting to perform inspection or main-
tenance on the tool. Failure to switch o󰀨 and remove
the battery cartridge may result in serious personal
injury from accidental start-up.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Battery guard
WARNING: Do not remove the battery
guard. Do not use the tool with the battery guard
removed or damaged. Direct impact to the battery
cartridge may cause battery malfunction and result
in injury and/or re. If the battery guard is deformed
or damaged, contact your authorized service center
for repairs.
► Fig.19: 1. Battery guard
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
TROUBLESHOOTING
Before asking for repairs, conduct your own inspection rst. If you nd a problem that is not explained in the manual,
do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace-
ment parts for repairs.
State of abnormality Probable cause (malfunction) Remedy
Motor does not run. Battery cartridge is not installed. Install the battery cartridge.
Battery problem (under voltage) Recharge the battery. If recharging is not e󰀨ective,
replace battery.
The drive system does not work
correctly.
Ask your local authorized service center for repair.
Motor stops running after a little use. Rotation is in reverse. Change the direction of rotation with the reversing
switch.
Battery's charge level is low. Recharge the battery. If recharging is not e󰀨ective,
replace battery.
Overheating. Stop using of tool to allow it to cool down.
It does not reach maximum RPM. Battery is installed improperly. Install the battery cartridge as described in this
manual.
Battery power is dropping. Recharge the battery. If recharging is not e󰀨ective,
replace battery.
The drive system does not work
correctly.
Ask your local authorized service center for repair.

14 ENGLISH
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita tool
specied in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
Refer to "Approved attachment" section for the applica-
ble models for this tool.
• Edger attachment
• Brushcutter attachment
• String trimmer attachment
• Rotary scissors attachment
• Grass trimmer attachment
• Hedge trimmer attachment
• Ground trimmer attachment
• Pole saw attachment
• Co󰀨ee harvester attachment
• Cultivator attachment
• Shaft extension attachment
• Power brush attachment
• Power sweep attachment
• Blower attachment
• Makita genuine battery and charger
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
di󰀨er from country to country.

15 SLOVENŠČINA
SLOVENŠČINA (Originalna navodila)
TEHNIČNI PODATKI
Model: DUX60
Hitrost brez obremenitve
(brez priključka)
Počasi 0 – 5.700 min-1
Srednje 0 – 8.200 min-1
Hitro 0 – 9.700 min-1
Celotna dolžina 1.011 mm
Nazivna napetost D.C. 36 V
Neto teža 5,1 kg – 11,7 kg
• Ker nenehno opravljamo raziskave in razvijamo svoje izdelke, se lahko tehnični podatki v tem dokumentu spremenijo brez obvestila.
• Tehnični podatki se lahko razlikujejo od države do države.
• Teža se lahko razlikuje glede na priključke, vključno z akumulatorsko baterijo. Najlažja in najtežja kombinacija v
skladu s postopkom EPTA 01/2014 sta prikazani v preglednici.
Uporabna akumulatorska baterija in polnilnik
Baterijski vložek BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B
Polnilnik DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
DC18SH
• Nekatere zgoraj navedene akumulatorske baterije in polnilniki morda v vaši državi prebivališča niso na voljo.
OPOZORILO: Uporabljajte le zgoraj navedene akumulatorske baterije in polnilnike. Uporaba drugih
akumulatorskih baterij in polnilnikov lahko povzroči telesne poškodbe in/ali požar.
Priporočen vir napajanja s kablom
Akumulatorska baterija s kablom BL36120A
Prenosna polnilna enota PDC01 / PDC1200
• Vir(i) napajanja s kablom, navedeni zgoraj, morda v vaši državi prebivališča niso na voljo.
• Pred uporabo vira napajanja s kablom preberite navodila in opozorilne znake na njem.
Hitrost brez obremenitve s priključkom
Model Hitrost vrtenja
Počasi Srednje Hitro
EM401MP 0 – 4.200 min-1 0 – 6.000 min-1 0 – 7.100 min-1
EM404MP / EM406MP 0 – 3.500 min-1 0 – 5.000 min-1 0 – 6.000 min-1
EM407MP Zgornje rezilo 0 – 220 min-1 0 – 310 min-1 0 – 370 min-1
Spodnje rezilo 0 – 470 min-1 0 – 670 min-1 0 – 790 min-1
EM408MP / EM409MP 0 – 4.200 min-1 0 – 6.000 min-1 0 – 7.100 min-1
EN401MP / EN410MP / EN420MP
(Hodi na minuto)
0 – 2.400 min-1 0 – 3.400 min-1 0 – 4.000 min-1
EY401MP (hitrost verige) 0 – 12 m/s 0 – 17 m/s 0 – 20 m/s
EY403MP (hitrost verige) 0 – 11 m/s 0 – 16 m/s 0 – 19 m/s
KR400MP 0 – 160 min-1 0 – 230 min-1 0 – 280 min-1
KR401MP 0 – 130 min-1 0 – 190 min-1 0 – 230 min-1
EE400MP 0 – 2.800 min-1 0 – 4.000 min-1 0 – 4.700 min-1
EJ400MP 0 – 1.600 min-1 0 – 2.300 min-1 0 – 2.800 min-1
BR400MP 0 – 130 min-1 0 – 190 min-1 0 – 230 min-1
SW400MP 0 – 130 min-1 0 – 190 min-1 0 – 230 min-1
UB400MP 0 – 5.700 min-1 0 – 7.850 min-1 0 – 8.250 min-1
UB401MP 0 – 5.700 min-1 0 – 7.850 min-1 0 – 8.250 min-1

16 SLOVENŠČINA
Odobreni priključki
Vrsta Model
Priključek motorne kose EM401MP / EM404MP
Priključek kosilnice z nitjo EM406MP
Priključek rotacijskih škarij EM407MP
Priključek kosilnice z nitko EM408MP / EM409MP
Priključek škarij za živo mejo EN401MP / EN410MP
Priključek za talni rezalnik EN420MP
Priključek teleskopske žage EY401MP / EY403MP
Priključek kultivatorja KR400MP / KR401MP
Priključek rezalnika za robove EE400MP
Priključek obiralnika kave EJ400MP
Priključek podaljška droga LE400MP
Električni priključek za krtačenje BR400MP
Električni priključek za pometanje SW400MP
Nastavek za pihanje UB400MP / UB401MP
Simboli
Naslednji simboli se lahko uporabljajo v povezavi s
strojem. Pred uporabo izdelka se obvezno seznanite z
njihovim pomenom.
Preberite navodila za uporabo.
Potrebna je posebna pozornost in
previdnost.
Ne izpostavljajte vlagi.
Ni-MH
Li-ion
Samo za države EU
Zaradi prisotnosti nevarnih komponent v
opremi imajo lahko uporabljena električna
in elektronska oprema, akumulatorji in
baterije negativen vpliv na okolje in zdravje
ljudi.
Električnih in elektronskih naprav ali baterij
ne odlagajte med gospodinjske odpadke!
Skladno z evropsko Direktivo o odpadni
električni in elektronski opremi, o akumula-
torjih in baterijah ter odpadnih akumulator-
jih in baterijah ter njeno uporabo v državnih
zakonih morate rabljeno električno in
elektronsko opremo, baterije in akumula-
torje zbirati ločeno ter dostaviti na posebno
zbiralno mesto za komunalne odpadke, ki
deluje skladno s predpisi za zaščito okolja.
To nakazuje simbol prečrtanega smetnjaka
s kolesi, ki je natisnjen na opremi.
Predvidena uporaba
Ta brezžična večfunkcijska pogonska glava je name-
njena za odobrene priključke, navedene v razdelku
„TEHNIČNI PODATKI“ teh navodil za uporabo. Enote
nikoli ne uporabljajte za druge namene.
OPOZORILO: Pred uporabo preberite
navodila za uporabo priključka in ta navodila za
uporabo. Neupoštevanje opozoril in navodil lahko
privede do hudih telesnih poškodb.

17 SLOVENŠČINA
Hrup
Priključek Povprečna raven zvoč-
nega tlaka Povprečna raven zvočne moči Veljavni standard
LpA (dB (A))
Odstopanje K
(dB (A))
LWA (dB (A)) Odstopanje K
(dB (A))
EM401MP (kot motorna kosa) 78,5 1,0 90,2 1,5 EN11806
EM401MP (kot kosilnica z nitjo) Najlonska rezalna glava 84,3 0,6 93,3 1,6 EN50636-2-91
Plastično rezilo 77,0 1,7 88,5 1,8 EN50636-2-91
EM404MP (kot motorna kosa) 82,5 2,2 93,3 2,9 EN11806
EM404MP (kot kosilnica z nitjo) Najlonska rezalna glava 84,7 2,3 92,8 1,6 EN50636-2-91
Plastično rezilo 76,0 1,8 87,7 1,5 EN50636-2-91
EM406MP Najlonska rezalna glava 84,7 2,5 93,5 2,2 EN50636-2-91
Plastično rezilo 77,0 1,9 85,6 2,0 EN50636-2-91
EM407MP 83,2 3,9 99,3 2,5 ISO22868
(ISO11806-1)
EM408MP (kot motorna kosa) 79,9 2,6 94,5 2,0 ISO22868
(ISO11806-1)
EM408MP (kot kosilnica z nitjo) Najlonska rezalna glava 79,0 2,6 91,8 1,7 ISO22868
(ISO11806-1)/
EN50636-2-91
Plastično rezilo 80,1 0,7 91,0 1,6 ISO22868
(ISO11806-1)/
EN50636-2-91
EM409MP Najlonska rezalna glava 79,9 2,3 92,7 0,9 ISO22868
(ISO11806-1)/
EN50636-2-91
Plastično rezilo 80,3 0,9 91,2 2,2 ISO22868
(ISO11806-1)/
EN50636-2-91
EN401MP 82 393 3 EN62841-4-2
EN401MP + LE400MP 82 393 3 EN62841-4-2
EN410MP 77 388 3 EN62841-4-2
EN410MP + LE400MP 77 388 3 EN62841-4-2
EN420MP 83 394 3 EN62841-4-2
EY401MP 92,5 1,4 101,9 1,4 ISO11680-1
EY401MP + LE400MP 86,6 1,0 101,2 1,0 ISO11680-1
EY403MP 96 3105 3
ISO22868
(ISO11680-1)
EY403MP+LE400MP 96 3105 3 ISO22868
(ISO11680-1)
KR400MP 76,7 2,2 84,2 1,0 EN709
KR401MP 73,1 1,4 84,2 1,8 EN709
EE400MP 74,8 1,5 88,2 2,6 ISO11789
EJ400MP 87,4 1,4 94,5 1,3 ISO10517
EJ400MP + LE400MP 85,6 1,0 95,5 1,3 ISO10517
BR400MP 79,5 0,9 89,0 0,7
EN60335-2-72
SW400MP 80,1 1,8 88,8 0,7 EN60335-2-72
UB400MP 89,8 0,4 100,4 0,8 EN50636-2-100
UB401MP 83,4 1,1 94,1 0,8 EN50636-2-100
• Tudi če je zgoraj navedena raven zvočnega tlaka 80 dB (A) ali manj, lahko med delovanjem preseže 80 dB (A).
Uporabljajte zaščito za sluh.
OPOMBA: Navedene vrednosti oddajanja hrupa so bile izmerjene v skladu s standardnimi metodami testiranja in
se lahko uporabljajo za primerjavo orodij.
OPOMBA: Navedene vrednosti oddajanja hrupa se lahko uporabljajo tudi pri predhodni oceni izpostavljenosti.

18 SLOVENŠČINA
Vibracije
Priključek Levi ročaj (sprednje držalo) Desni ročaj (zadnje držalo) Veljavni
standard
ah (m/s2)
Odstopanje K
(m/s2)
ah (m/s2) Odstopanje K
(m/s2)
EM401MP (kot motorna kosa) 3,0 1,5 2,5 1,5 EN11806
EM401MP (kot kosilnica z nitjo) Najlonska rezalna glava 5,0 1,5 2,5 1,5 EN50636-2-91
Plastično rezilo 2,5 1,5 2,5 1,5 EN50636-2-91
EM404MP (kot motorna kosa) 3,0 1,5 2,5 1,5 EN11806
EM404MP (kot kosilnica z nitjo) Najlonska rezalna glava 3,0 1,5 2,5 1,5 EN50636-2-91
Plastično rezilo 2,5 1,5 2,5 1,5 EN50636-2-91
EM406MP Najlonska rezalna glava 2,5 1,5 2,5 1,5 EN50636-2-91
Plastično rezilo 4,0 1,5 2,5 1,5 EN50636-2-91
EM407MP 2,5 1,5 2,5 1,5 ISO22867
(ISO11806-1)
EM408MP (kot motorna kosa) 2,5 1,5 2,5 1,5 ISO22867
(ISO11806-1)
EM408MP (kot kosilnica z nitjo) Najlonska rezalna glava 2,5 1,5 2,5 1,5 ISO22867
(ISO11806-1)
Plastično rezilo 2,5 1,5 2,5 1,5 ISO22867
(ISO11806-1)
EM409MP Najlonska rezalna glava 2,5 1,5 2,5 1,5 ISO22867
(ISO11806-1)
Plastično rezilo 2,5 1,5 2,5 1,5 ISO22867
(ISO11806-1)
EN401MP 5,5 1,5 3,5 1,5 EN62841-4-2
EN401MP + LE400MP 5,5 1,5 4,0 1,5 EN62841-4-2
EN410MP 4,0 1,5 2,5 1,5 EN62841-4-2
EN410MP + LE400MP 4,5 1,5 2,5 1,5 EN62841-4-2
EN420MP 6,5 1,5 4,0 1,5 EN62841-4-2
EY401MP 2,5 1,5 2,5 1,5 ISO11680-1
EY401MP + LE400MP 5,5 1,5 2,5 1,5 ISO11680-1
EY403MP 2,7 1,5 2,5 1,5
ISO22867
(ISO11680-1)
EY403MP+LE400MP 3,0 1,5 2,5 1,5 ISO22867
(ISO11680-1)
KR400MP 2,5 1,5 2,5 1,5 EN709
KR401MP 2,5 1,5 2,5 1,5 EN709
EE400MP 2,5 1,5 2,5 1,5 ISO11789
EJ400MP 4,0 1,5 3,0 1,5 ISO10517
EJ400MP + LE400MP 4,5 1,5 3,0 1,5 ISO10517
BR400MP 2,5 1,5 2,5 1,5
EN60335-2-72
SW400MP 2,6 1,5 2,6 1,5 EN60335-2-72
UB400MP 4,5 2,0 2,5 1,5 EN50636-2-100
UB401MP 3,6 1,7 2,5 1,5 EN50636-2-100
OPOMBA: Navedene skupne vrednosti oddajanja vibracij so bile izmerjene v skladu s standardnimi metodami
testiranja in se lahko uporabljajo za primerjavo orodij.
OPOMBA: Navedene skupne vrednosti oddajanja vibracij se lahko uporabljajo tudi pri predhodni oceni
izpostavljenosti.

19 SLOVENŠČINA
OPOZORILO: Oddajanje vibracij med dejansko uporabo električnega orodja se lahko razlikuje od
navedenih vrednosti, odvisno od načina uporabe orodja in predvsem vrste obdelovanca.
OPOZORILO: Upravljavec mora za lastno zaščito poznati varnostne ukrepe, ki temeljijo na oceni izpo-
stavljenosti v dejanskih pogojih uporabe (poleg časa proženja je treba upoštevati celoten delovni cikel,
vključno s časom, ko je orodje izklopljeno, in časom, ko deluje v prostem teku).
Izjava o skladnosti ES
Samo za evropske države
Izjava ES o skladnosti je vključena v dodatku A, ki je
priložen tem navodilom za uporabo.
VARNOSTNA OPOZORILA
Splošna varnostna opozorila za
električno orodje
OPOZORILO: Preberite vsa varnostna opo-
zorila in navodila s slikami in tehničnimi podatki,
ki so dobavljeni skupaj z električnim orodjem.
Ob neupoštevanju spodaj navedenih navodil obstaja
nevarnost električnega udara, požara in/ali hudih
telesnih poškodb.
Shranite vsa opozorila in navo-
dila za poznejšo uporabo.
Izraz „električno orodje“ v opozorilih se nanaša na vaše
električno orodje (s kablom) ali baterijsko električno
orodje (brez kabla).
Pomembna varnostna navodila za
akumulatorsko baterijo
1. Pred uporabo baterijskega vložka preberite
vsa navodila in opozorilne oznake na (1) pol-
nilniku akumulatorja, (2) akumulatorju in (3)
izdelku, ki uporablja akumulator.
2. Ne razstavljajte ali spreminjajte akumulatorske
baterije. S tem lahko povzročite požar, preko-
merno vročino ali eksplozijo.
3. Če se je čas delovanja občutno skrajšal, takoj
prenehajte uporabljati orodje. V nasprotnem
primeru lahko pride do pregretja, morebitnih
opeklin in celo eksplozije.
4. Če pride elektrolit v stik z očmi, jih sperite s
čisto vodo in takoj poiščite zdravniško pomoč.
Posledica je lahko izguba vida.
5. Ne povzročite kratkega stika baterijskega
vložka:
(1) Ne dotikajte se priključkov s kakršnim
koli prevodnim materialom.
(2) Izogibajte se shranjevanju baterijskega
vložka v vsebniku z drugimi kovinskimi
predmeti kot so žeblji, kovanci itn.
(3) Ne izpostavljajte baterijskega vložka vodi
ali dežju.
Kratek stik akumulatorja lahko povzroči velik
električni tok, pregrevanje, morebitne opekline
in celo okvaro.
6. Ne shranjujte in uporabljajte orodja in akumu-
latorske baterije na mestih, kjer lahko tempera-
tura doseže ali preseže 50 °C (122 °F).
7. Ne sežigajte baterijskega vložka, tudi če je
hudo poškodovan ali v celoti izpraznjen.
Baterijski vložek lahko v ognju eksplodira.
8. Ne pribijajte, režite, drobite, mečite, spuščajte
akumulatorske baterije oziroma ne udarjajte
z akumulatorsko baterijo po trdem predmetu.
Takšno ravnanje lahko povzroči požar, preko-
merno vročino ali eksplozijo.
9. Ne uporabljajte poškodovanih akumulatorjev.
10. Priložene litij-ionske baterije ustrezajo zahte-
vam zakonodaje v zvezi z nevarnim blagom.
Za komercialne prevoze, npr. tiste, ki jih opravljajo
tretje stranke in carinski posredniki, je treba upoštevati
posebne zahteve v zvezi z embalažo in označevanjem.
Med postopkom priprave na odpremo izdelka se je
treba posvetovati s strokovnjakom za nevarne snovi. Pri
tem upoštevajte tudi podrobnejše nacionalne predpise.
Odprte stike oblepite z lepilnim trakom ali jih dru-
gače zaščitite, baterijo pa zapakirajte tako, da se v
embalaži ne more premikati.
11. Ko odstranjujete akumulatorsko baterijo, jo
vzemite iz orodja in varno zavrzite. Upoštevajte
lokalne uredbe glede odlaganja baterije.
12.
Baterije uporabljajte le z izdelki, ki jih določi Makita.
Če namestite baterije v neskladne izdelke, lahko pride do
požara, pregrevanja, eksplozije ali puščanja elektrolita.
13. Če orodja dlje časa ne uporabljate, morate iz
njega odstraniti baterijo.
14. Med uporabo in po uporabi lahko akumu-
latorska baterija postane vroča in povzroči
opekline. Z vročimi akumulatorskimi baterijami
ravnajte pazljivo.
15.
Ne dotikajte se priključka orodja takoj po uporabi,
ker se lahko dovolj segreje, da povzroči opekline.
16. Ne dovolite, da bi se v priključke, odprtine in
utore akumulatorske baterije zlepili ostružki, prah
ali zemlja. Umazanija lahko povzroči slabše delova-
nje ali okvaro orodja oziroma akumulatorske baterije.
17. Razen če orodje podpira uporabo v bližini
visokonapetostnih električnih vodov, akumula-
torske baterije ne uporabljajte v bližini visoko-
napetostnih električnih vodov. Takšna uporaba
lahko povzroči motnje v delovanju ali okvaro
orodja oziroma akumulatorske baterije.
18. Baterijo hranite izven dosega otrok.
SHRANITE TA NAVODILA.
POZOR: Uporabljajte le originalne baterije
Makita. Če uporabljate neoriginalne baterije Makita
ali baterije, ki so bile spremenjene, lahko pride do
eksplozije baterije in posledično do požara, telesnih
poškodb ali materialne škode. S takšno uporabo
boste tudi razveljavili garancijo Makita za orodje in
polnilnik Makita.

20 SLOVENŠČINA
Nasveti za ohranjanje največje
zmogljivosti akumulatorja
1. Napolnite baterijski vložek, preden se v celoti izprazni.
Ko opazite, da ima orodje manjšo moč, vedno ustavite
delovanje orodja in napolnite baterijski vložek.
2. Nikoli znova ne polnite popolnoma napol-
njenega baterijskega vložka. Prenapolnjenje
skrajša življenjsko dobo akumulatorja.
3. Baterijski vložek s sobno temperaturo pol-
nite pri temperaturi okolja od 10 °C do 40 °C.
Počakajte, da se vroč baterijski vložek pred
polnjenjem ohladi.
4. Ko akumulatorske baterije ne uporabljate, jo
odstranite iz orodja ali polnilnika.
5. Če baterijskega vložka ne uporabljate dalj časa
(več kot 6 mesecev), ga napolnite.
OPIS DELOV
► Sl.1
1Akumulatorska baterija 2Ročica za zaklep 3Sprožilec 4Obešalo
5Ročaj 6Sprostilni gumb 7Pregrada (odvisno od
države)
8Indikator hitrosti
9Lučka za vklop/izklop 10 Glavni gumb za vklop/
izklop
11 Gumb za spremembo
smeri
12 Naramni pas
OPIS DELOVANJA
OPOZORILO: Pred nastavljanjem ali pre-
izkusom delovanja orodja se prepričajte, da je
orodje izklopljeno in je akumulatorska baterija
odstranjena. Če orodja ne izklopite in ne odstranite
akumulatorske baterije, lahko pride do resnih telesnih
poškodb zaradi nenamernega zagona.
Nameščanje ali odstranjevanje
akumulatorske baterije
POZOR: Vedno izklopite orodje, preden name-
stite ali odstranite akumulatorsko baterijo.
POZOR: Kadar nameščate ali odstranjujete
akumulatorsko baterijo, trdno držite orodje in
akumulatorsko baterijo. Če orodja in akumulatorske
baterije ne držite trdno, se lahko zgodi, da vam zdr-
sneta iz rok, posledica pa je lahko poškodba orodja in
akumulatorske baterije ter telesna poškodba.
► Sl.2: 1. Rdeči indikator 2. Gumb 3. Baterijski vložek
Če želite odstraniti akumulatorsko baterijo, jo potisnite iz
orodja, pri tem pa pomikajte gumb na sprednji strani vložka.
Akumulatorsko baterijo vstavite tako, da poravnate
jeziček na bateriji z utorom na ohišju in jo potisnete v
ležišče. Potisnite jo do konca, da se zaskoči. Če vidite
rdeči indikator, kot je prikazano na sliki, se akumulator-
ska baterija ni ustrezno zaskočila.
POZOR: Vedno namestite akumulatorsko
baterijo tako, da rdeči indikator ni več viden. Če
tega ne upoštevate, lahko baterija nepričakovano
pade iz orodja in poškoduje vas ali osebe v neposre-
dni bližini.
POZOR: Ne nameščajte akumulatorske bate-
rije s silo. Če se akumulatorska baterija ne zaskoči
zlahka, ni pravilno vstavljena.
Zaščitni sistem orodja/akumulatorja
Orodje je opremljeno z zaščitnim sistemom za orodje/
akumulator. Sistem samodejno prekine napajanje orodja,
da podaljša življenjsko dobo orodja in akumulatorja.
Orodje se samodejno zaustavi med delovanjem, če
orodje ali akumulator delujeta pod naslednjimi pogoji:
Stanje Indikatorske lučke
Sveti Ne sveti Utripa
Preobremenitev
Pregrevanje
Prekomerna
izpraznjenost
Zaščita pred preobremenitvijo
Če je orodje preobremenjeno zaradi zapletle trave
in oblog, začneta utripati lučka in srednja lučka,
orodje pa se samodejno zaustavi.
V tem primeru izklopite orodje in prenehajte izvajati
delo, ki je povzročilo preobremenitev orodja. Nato vklo-
pite orodje in ga znova zaženite.
Varovalo pred pregrevanjem za
orodje in akumulator
Pri pregrevanju utripajo vse lučke za hitrost.
V primeru pregrevanja se orodje samodejno zaustavi.
Počakajte, da se orodje in/ali akumulator ohladita,
preden znova vklopite orodje.