Manrose COMT Series User manual

INSTALLATION INSTRUCTIONS
Switch off mains supply before making any electrical connections.
Installation must be supervised by a qualified electrician.
This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory and mental capabilities
or lack of experience and knowledge if they have been given
supervision or instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children
without supervision.
Precautions must be taken to avoid the back-flow of gases into the
room from the open flue of gas or other open-fire appliances when
mounted in outside windows or walls.
Fan must be disconnected from electrical power before any
maintenance is carried out.
Installation Instructions for the
COMT and COMTK Range of Wall Fans
Wiring
1. Switch off mains supply before making electrical
connections. If in any doubt contact a qualified
electrician.
2. These units are for fixed wiring only. A flexible cord
must not be used. All wiring must be fixed securely
and the cable to the fan should be a minimum of
1mm2in section. All wiring must comply with current
I.E.E. Regulations or local regulations if outside the
UK.
3. A double pole fused spur having contact separation
of at least 3mm in all pole must be used and fitted
with a 3A fuse.
4. This fan is double insulated and does not require an
earth connection.
5. The fan should not be accessible to a person using
either the shower or the bath.
Location
1. When installing fan through an external wall, an
external wall grille must be fitted at all times.
2. For best results this Extractor Fan should be
fitted as high on the wall as possible, or if
preferred, on the ceiling. Note: Pullcord models
should not be installed in a ceiling.
3. Do not install the unit within a shower cubicle
or anywhere else where there is a risk of being
sprayed with water (Please see our range of
showerfans for these installations.).
4. If the fan is installed in a room containing a fuel
burning appliance, the installer must ensure that
the air replacement is adequate for both the fan
and the fuel burning appliance.

COMTK Series
1. Cut a hole through the wall to suit fan type. See diagram below and dimensions D&E
2. Fit the telescopic sleeve into the wall. The sleeve is adjustable and suitable for cavity or solid walls. ( A longer extension
sleeve is available to order) Make sure there is a slight tilt to the outside to allow any water which may get in through the
outside grille, drain to the outside.
IMPORTANT Ensure a minimum 300mm of power cable is passed through the cable entry for the electrical
connections.
3. Build in the sleeve and make good around the edges. The external and internal grilles have a flange that over hangs the
sleeve.
COMT Series
4. Is supplied without the sleeve and external grille. The series is designed as a replacement for existing installations and fits
most makes of sleeve and wall box with little or no modifications to the existing wall box installations. See Diagram 2 for
dimensions.
5. All models of the series are secured internally by 4 mounting screws, and secured externally by 4 mounting Screws. After
fixing the front and rear sections ensure you insert the hole plugs provided.
IMPORTANT: Always ensure that the supply cable cannot obstruct the fan blade.
PRODUCT A B C D E
COMTK150 310mm 310mm 160-290mm 258mm 288mm
COMTK230 390mm 390mm 160-290mm 359mm 366mm
COMTK300 470mm 470mm 160-290mm 404mm 447mm
E
A
B
C
D
Diagram 1

6. Electrical Connections (COMTK/COMT Series)
COMTK150 & COMT150
This model can only be wired for extract. Connect the power into the terminal located on the rear of the fan.
Fit cover with screw
when electrical
connections are
completed
1 LIVE SUPPLY
2 NEUTRAL SUPPLY
1
2Power Cable
Connector
Cable Grip
COMTK230/300 and COMT230/300
The electrical connection using fixed wiring built into the wall is made via a 5 pin plug in connector (complete with
cable grip) which is supplied with each fan unit for ease of electrical installation when connected to the incoming power
cable it simply plugs into the rear of the fan unit.
NOTE (Diagram A) The COMTK 230/300 series can be wired via 3 core cable for EXTRACT only.
NOTE (Diagram B) The COMTK 230/300 series can be wired via 3 core cable for INTAKE only.
NOTE (Diagram C) If the 2 speed reversible controller is used with the COMTK 230/300 series, 5 core cable is
required (which is available separately).
These fans are double insulated and do not require an earth. All wiring must comply with current IEE regulations. A
double pole isolating switch, having a contact separation of at least 3mm in all poles, must be used with a 3amp fuse
fitted. The fan must not be accessible to a person using either a bath or a shower and mounted a minimum of 1.8m
from the floor.
PRODUCT A B C
COMT150 310mm 310mm 110mm
COMT230 390mm 390mm 138mm
COMT300 470mm 470mm 154mm
A
B
C
COMT Series Dimensions
Fan is attached to outer
grille by four screws and locking tabs
Diagram 2

NEUTRAL IN
LIVE IN
NEUTRAL IN
LIVE IN
NEUTRAL IN
INPUT ONLY IN
EXTRACT ONLY IN
LIVE IN
EXTRACT ONLY
INPUT ONLY
REVERSIBLE SPEED CONTROLLER
Plug Wiring Diagram
Diagram A
Diagram B
Diagram C
WIRING DIAGRAM
DIAGRAM A - EXTRACT ONLY
To change the airflow direction remove link from terminal 1 in the plug and connect into terminal 2.
DIAGRAM B INTAKE ONLY
All models are pre wired in factory to extract only. When the cable supplied with the socket for test purposes is
connected to a fused spur or plug socket.
DIAGRAM C - REVERSIBLE SPEED CONTROLLER
For the COMTK 230/300 models using the reversible variable speed controller part no. COMTSCVR.
7. Electrical
220-240V AC.50HZ IP44 T. Max 40 deg C
COMT/COMTK 150 - 25W
COMT/COMTK 230 - 48W
COMT/COMTK 300 - 60W
THIS FAN SERIES IS DOUBLE INSULATED AND DOES NOT REQUIRE AN EARTH. THE EARTH TERMINAL IS
PROVIDED FOR SPECIAL INSTALLATIONS ONLY.
NOTE:
Do not install within a shower cubicle (Use our SF100, SF120, SF150 range of shower fans) or anywhere else where
there is a high risk of the fan being sprayed with water.
Fan to be fitted a minimum 2.3 metres from the floor.
077311 06/15