Marea Smart B58007 User manual

B58007
User manual
Please read this manual before using the product to
fully understand its use and operation.

CAUTION
The company reserves the right to modify the contents of
this manual without any further notification. Some
functions may vary in certain versions of software.
Please charge this product with the charger provided for
no less than 2 hours before using it for the first time.Use
only the charger that is included with the product. Make
sure that the charger and the smart watch are properly
connected while charging. Do not charge if the watch has
water (or sweat) to avoid short circuits and damaging the
product.
The two contacts of the charging cable cannot be in
contact with a conductor material at the same time, it
will cause a short circuit and burn.
Avoid hitting the smart watch, it could break the glass.
The waterproof rank is IP68, therefore the smart watch
can be used for daily life. But the smart watch cannot be
used for diving or be under water for a long time.
Furthermore, the smart watch cannot be used in showers
/ baths with hot water (the water steam can damage it)
or in salt water (if it entered the smart watch, it would
corrode the internal parts).
System Requirements:
Android: Android 4.2 or above
iPhone: iOS 10.0 or above

Download and install the application
1. Go to our website www.mareasmart.com and find your
smart watch model. The model number is found on the
back of the smart watch (it starts with “B” and is followed
by five digits).
2. Download and install on your phone the official app that
corresponds with your smart watch model.
3. Open the app and enable all the permissions that the app
requests.
4. Turn on Bluetooth on your phone.
5. Make sure that the smart watch has not been linked
directly through Bluetooth to your phone. If so, unlink it.
6. Bind your Marea Smart watch through the app.
Notes on linking:
Only one smart watch pairing application should be
installed on the phone to ensure that the connection
with the smart watch is normal. If several applications
are connected, they can affect the connection between
the watch and the phone. Some Android phones will
prompt you that they cannot install the app. Please go to
‘settings’ of the phone and authorize the ‘Unknown
source’.
When the mobile phone requests permissions, click
"Allow". On the contrary, you may not receive
notifications, scan QR codes, open the remote camera or
use other functions. These permissions do not affect the
flow of the phone or other information on the phone.

Some Android phones may accidentally close the app
when cleaning the applications. Please keep the app
running in the background. To turn on this function on
your phone: open the phone settings - application
management - official application - rights management -
backstage management - select background running. The
setting method may be different due to different mobile
phone versions and models.
For iPhone: if the phone is in standby or hibernation
mode for a long time (for example, the phone has not
been in use for 2 hours or more and the screen is off), the
application will be closed by the iOS system , so the
application and the watch will be disconnected and the
application functions will not be available. Re-activate
the phone and it will automatically reconnect.
Smart watch operation

Turn on/off
Press and hold the side button for 3 seconds to turn on the
smart watch; short press the side button to activate the
watch when in standbymode.
Press and hold the side button for 3 seconds to turn off the
smart watch.
Charger
When charging, the charger must contact the charge port
on the back of the case’s watch as shown:
Button and screen operation
From the home screen on the smart watch:
Swipe down to see the status bar. It shows the
connection status and battery, and includes quick access
to some functions (brightness control, weather, find
phone, settings, chronograph and info about smart
watch).
Swipe up to enter the main menu.
Swipe right to enter the message interface.
Swipe left to enter the shortcut menu. It includes
exercise data (swipe up to view the number of steps,

distance, and calorie consumption of the day), heart rate
monitor and sleep monitor.
Return
From any function, swipe right to return to the previous
menu or short press the side button to return to the home
screen.
Home screen selection
Long press the home screen to enter the selection
interface, swipe right / left to see all available options. Click
on the desired screen to make it your home screen.
On the app you can download other predesigned home
screens as well as select an image saved on the phone to
set as your home screen.
Main functions in Smart watch
The main menu includes the following functions:
Messages
Shows the last 10 messages / notifications. The
phone and the watch must be linked and within
the Bluetooth range. Slide to the bottom and
press the delete icon to clear all message
records. The last notification received will
replace the oldest one. On the app you can
select what type of notifications you want to
receive on the smart watch.

Data
Shows the steps taken, the distance traveled and
the calories consumed on the current day. Slide
up to see hourly graphs. The data is cleared at
00:00 every day. You can check the historical
data on the app.
Motion
Includes different sport modes: walking,
running, cycling, skipping rope, badminton,
basketball, football.
Select the corresponding exercise mode, click on
the start button to begin the recording and the
pause icon to pause the exercise. Click on the
end button to end the exercise and save the
data. The exercise data can be saved when the
exercise time is longer than 1 minute (if not, it
will prompt "Too little data to save").
On the app you can check the historical data.
Heart Rate
Upon entering the function, the heart rate
measurement will start automatically. Wait
about 10-20 seconds for the measurement to
finish and the result will be displayed. The data
will be saved in more detail on the app.

Notes on health functions:
The heart rate, blood pressure, and blood oxygen
functions require the watch and arm to be in contact,
and the watch should not be too tight or too loose. The
test can be inaccurate if it is too tight because it will
ECG
Enter the ECG menu on the app and then enter
the ECG function on the smart watch. Wait for a
while for the measurement to finish and the
data will be saved on the app. The phone and
the watch must be linked and within the
Bluetooth range.
Blood Pressure
Upon entering the function, the blood pressure
measurement will start automatically. Wait
about 10-20 seconds for the measurement to
finish and the result will be displayed. The data
will be saved in more detail on the app.
Blood Oxygen
Upon entering the function, the blood oxygen
measurement will start automatically. Wait
about 10-20 seconds for the measurement to
finish and the result will be displayed. The data
will be saved in more detail on the app.

affect blood flow, and if it is too loose because it will
affect the monitoring of the heart rate sensor.
The results of the smart watch measurements are only
indicative and cannot substitute in any case for any
medical test. Please follow your doctor's instructions and
do not rely solely on these results for an evaluation.
Music remote control
Displays buttons to play / pause and skip to
previous or next song, to remotely control the
music playing on the paired phone. The phone
and the watch must be linked and within the
Bluetooth range.
Sleep Monitor
If you have worn the watch during the previous
night, it shows the total sleep time of last night,
as well as light and deep sleep times. You can
check the historical data on the app.
Sleep monitoring time period: from 18:00 to
10:00 the next day.
Stopwatch
Click on the start icon to start the count. When
the time is paused, click the reset icon to reset to
0.

Weather
Displays the current weather and temperature.
The phone and the watch must be linked so the
watch can receive the weather info from the
phone.
Find phone
The paired phone will ring so you can find it. The
phone and the watch must be linked and within
the Bluetooth range.
Meteorology
Displays the day's ultraviolet (UV), atmospheric
pressure, and altitude conditions.
Breathing
There are three modes of breathing monitoring:
slow, moderate, and fast. The time of the
measurement can be set to 1, 2 or 3 minutes.
Massager
Click the green button to start the massage
(vibration) and the red button to stop it.
Female assistant
Shows the status of women's menstrual period.
On the app you can set and check the latest
month end time, the menstrual period length,