Mastercare MB-68 AV-XL User manual

Gen III Entree Bath
MODEL MB-68 AV-XL
OPERATION MANUAL
Important Safety Instructions
Read & Follow All Instructions Thoroughly
Important safety instructions. Read and follow all instructions thoroughly.
CAUTION: The caution heading identifies important maintenance and operation
information. Failure to obey a caution warning may result in damage to the Entree Bath
and may void the warranty.

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 2 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
WARNINGS
•Risk of accidental injury or drowning; children and impaired individuals should not use hydromassage
bathtub without trained adult supervision.
•To avoid injury; exercise care when entering or exiting the hydromassage bathtub.
•Do not use drugs or alcohol before or during the use of a hydromassage bathtub to avoid
unconsciousness and possible drowning.
•Risk of fetal injury, pregnant or possibly pregnant women should consult a physician before using a
hydromassage bathtub.
•Risk of hyperthermia and possible drowning; do not use a hydromassage bathtub immediately
following strenuous exercise.
•Risk of electrical shock; do not permit electrical appliances (such as a hair dryer, lamp, telephone, radio
or television) within 5 ft (1.5m) of the hydromassage bathtub.
•Proper electrical grounding must be performed by a licensed electrician following local, state and
federal codes. Test the ground fault circuit interrupter protecting this appliance periodically in
accordance with the manufacturer’s instructions.
•For permanently connected units) a green colored terminal (or a wire connector marked “g”, “gr”,
“ground” or “grounding”) is provided within the terminal compartment. To reduce the risk of electric
shock, connect the terminal or connector to the grounding terminal of your electric service or supply
panel with a conductor equivalent in size to the circuit conductors supplying this equipment.
•Risk of hyperthermia and/or possible drowning; water temperature in excess of 110o F or 43 o C may
be hazardous to your health. Check and adjust water temperature before use.
•Risk of hyperthermia. People using medications and/or having an adverse medical history should
consult a physician before using a hydromassage bathtub.

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 3 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
FEATURES AND OPERATING CONTROLS
Mixing Valve: Adjusts the temperature of
the mixer water to the shower Spray and tub
fill spigot. Turn counterclockwise for hotter
and clockwise for colder mixed water
(accuracy must be checked periodically per
facility protocol).
Tub Fill and Shower Spray Control Valves:
Turns ON/OFF and controls the flow of
mixed water to the tub fill spigot and shower
Spray.
Digital Thermometers: Digital readout
temperature of the mixed water to the
shower Spray and console (Preset at factory:
Field calibration maintenance, see
maintenance manual).
Emergency Door Open Button and the Door
Open Button at the same time to open the
door. It will override the drain water sensors.
Door Open/Close Button: To open door,
press and hold down the Door Open Button
until the door comes to a complete stop. To
close the door, press and hold down the
transmitter close button until the door
comes to a complete stop.
CAUTION: Check for obstructions in the
sensors, like wet clothes, foot, etc.
CAUTION: Door will not open if drain
sensors detect water in the tub unless the
Emergency Door Open Button is also
pressed at the same time.
CAUTION: Make sure the door comes to a complete stop to properly seal the
tub. Failure to do so may result in leaks. Contact Tech Support.
Foot-End
Controls
CONSOLE CONTROLS
Mixing Valve
Reservoir Fill
Control Valve
Door Open
Button
Console
Controls
Tub Fill and
Shower
Spray
Shower Spray
Control Valve
Liquid Dispensing
Controls
Door Close
Button
Reservoir Water
Thermometer
Tub Water
Thermometer
Emergency Door
Open Button
In an EMERGENCY, Press
emergency Door Open Button
and Open Door Button to
open door. It Override the
drain water sensors.

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 4 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
Thumb Screws: The thumb screws hold the service panel in
place and are to be removed only by authorized service
personnel for service access.
Liquid Dispensing Controls: These controls are used to
add Bath Oil and Shampoo directly into the bath water.
Drain Handle / Overflow: It is used to drain the tub and
to manage tub overflows.
BATHAIRE(SM) VARIABLE SPEED SYSTEM
CONTROL BASIC OPERATION:
BathAire(SM) On/Off Button: The BathAire(SM) can be
turned on or off by pressing the on/off button. Press the
button once and the BathAire(SM) will turn on. Press the
button once again and the BathAire(SM) will shut off.
BathAire(SM) More & Less Air/Heat Buttons: Once the
BathAire(SM) is on, it is in an adjustment mode. The
BathAire(SM) starts on at 60% of full volume. To increase
or decrease the air volume, press the air/heat + button
and hold down to increase level or the air/heat –button
to decrease level until the desired level is achieved. The
heat level is tied to the air volume and adjusted the same
way.
BathAire(SM) Wave Mode: To create a wave effect: Press
the wave button once for the long cycle, a second time
for the short cycle and a third time to return to normal
operation.
BathAire(SM) Purge Cycle: The purge cycle comes on
automatically 20 minutes after the BathAire(SM) system
has been turned off to remove any residual water from
around the aeration valve. It will then run for a period of
one minute. This is a preset of the motor and cannot be
turned off. It also is programmed to cycle every 24 hours,
so be aware it will run the purge cycle 24 hours after
BathAire(SM) being energized.
CONSOLE CONTROLS
Liquid
Dispensing
Controls
Liquid Dispensing
Drain Handle
/ Overflow
Thumb Screw
BathAire
Controls
On/Off
Button
Wave
Button
Less Air/Heat
Button
More Air/Heat
Button
AROMATHERAPY
CARTRIDGE HOLDER
AROMATHERAPY
SCENT CARTRIDGE
AROMATHERAPY
CAP

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 5 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
DISPENSING SYSTEM
Liquid Dispensing Controls: These controls are used to
add Bath Oil and Shampoo directly into the bath water.
Disinfectant Valve: Dispenses disinfectant through the
jets. Turn valve to the right for disinfecting. To the left for
flushing.
DISINFECTANT
VALVE
DISINFECTANT
BOTTLE
LIQUID DISPENSIG
CONTROLS
Bath Oil Button
Shampoo Button
SHAMPOO
BOTTLE
BATH OIL
BOTTLE
Liquid
Dispensing
Controls
Liquid Dispensing

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 6 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
OPERATION
Before operating the Entree Bath,
familiarize yourself with the key
features of the tub outlined in the
drawings supplied with these
instructions.
BATHING PROCEDURES
1. Fill the Reservoir:
a. Make sure the Reservoir Fill Control
Valve is in the closed position.
b. Bring the water temperature up to
normal bath temperature by placing the
shower Spray inside the bath, turned
toward the tub side wall. Then turn on
the Shower Spray Control Valve. Run the
water until it reaches the desired
temperature; adjust the water
temperature between 96° to 105° by
turning the Mixing Valve toward the hot
or cold side. Turn off the Shower Spray
Control Valve and replace the Shower
Spray.
WARNING: The temperature
of the bath water must never
exceed 110°. If you are
unable to adjust to the
normal level of 100° to 105°,
remove the individual and
report the problem to
maintenance. Do not use
bath until the mixing valve is
serviced to correct the
problem. Failure to heed this
warning could result in a
scalding injury to the
individual
c. The Reservoir Fill will shut off
automatically when the reservoir is full.
CONSOLE CONTROLS
Mixing Valve
Reservoir Fill
Control Valve
Door Open
Button
Tub Fill and
Shower
Spray
Shower Spray
Control Valve
Liquid Dispensing
Controls
Door Close
Button
Tank Temperature
Thermometer
Tub Water
Thermometer
Emergency Door
Open Button
BEFORE TRANSFER INTO THE TUB: FILL RESERVOIR:
•Make sure the Tub Fill Lever is turned to a full closed
position.
•Make sure the Shower Wand is directed into tub.
•Turn the Shower Spray Control Valve on.
•Adjust Mixing Valve for desired safe water temperature
(per facility policy) displayed on the bottom thermometer
labeled "Fill Temp".
•Turn Shower Control Spray Valve off.
•Turn Reservoir Fill Control Valve on.
•Continue monitoring to maintain desired temperature.
Reservoir fill will shut off automatically when full.

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 7 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
2. Turn On The BathAire(SM) by gently pushing
in on the BathAire(SM) On/Off Touch Pad
located on the lower left side deck of the
tub. (Do not use sharp object) This will
warm up the environment inside the tub.
You can increase or decrease the air flow by
pushing down on the plus (+) or minus (-)
section of the touch pad.
3. If Aromatherapy is desired, prior to
turning on the BathAire(SM), remove the
Aromatherapy Cap that is placed under the
Dispensing Box Access Door; place selected
scent cartridge or sachet in the
Aromatherapy Cartridge Holder and
securely close the access cap prior to
turning on BathAire(SM). (See Aromatherapy
Section in this manual)
CAUTION: Do NOT remove beads from
cartridge or sachet. Never place liquids in
the Aromatherapy Cartridge Holder.
On/Off
Button
Wave
Button
Less Air/Heat
Button
More Air/Heat
Button
BATHAIRE(SM) CONTROLS
Place AROMATHERAPY
CARTRIDGE in the aromatherapy
cartridge holder after removing
the aromatherapy cap under the
dispensing access door
Aromatherapy
Cartridge.
AROMATHERAPY
CARTRIDGE HOLDER
AROMATHERAPY
CAP

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 8 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
4. Transfer Individual to the Transfer Chair
a. Push down on the Open Door Button until the
door is fully opened and stops on its own.
b. Position the comfort pad group in the
Transfer Chair as follows; two rectangular
pads parallel about three to four inches apart
centered in the individual seating area, one
rectangular pad horizontally on the seat back
at approximately the lumbar area of the
individual
c. Push the Transfer Chair to the resident and
position for a normal wheel chair transfer.
d. LOCK the brakes by stepping down on the
LOCK-ARM TAB located on the back of the
rear casters.
Failure to lock the caster brakes before
the resident is transferred into the
Transporter could result in injury to the
operator or resident.
e. Transfer the patient on to the Transporter
using proper nursing transfer techniques.
f. Position the security belt attached to the
connecting knobs on the lift chair having one
belt crossed diagonal from one shoulder to
the opposite side hip and another belt
connecting the knobs on each side of the lap.
(See the Belting Diagram)
Comfort Pads Position
Open Door
Button
Bar
Security Knob
Security Knob
Security Knob
Comfort Pads
CASTER BREAK
LOCK-ARM TAB
CASTERS

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 9 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
1. Weigh The Individual:
If you have a scale on your Transfer Chair, now is the
time to take and record the weight of the individual.
Key steps to Get Accurate and Consistent Weights:
a. Before you transfer the resident on to the chair
push ZERO button below the scale display window
to zero out the weight of the chair.
b. The seat must not be touching the tub or anything
else, the front casters must be in the locked
position, all four casters must be on a consistent
level floor surface.
c. Transfer the resident onto the chair and position
them in a stable position. If the resident is
unstable or is moving around, wait until they settle
down and secure them with the SECURITY BELT.
d. The resident's weight will appear in the display
automatically. Make sure no one is touching or
leaning on the chair including yourself during the
weighting procedure.
e. Record the weight.
Note: If you accomplish the above steps every time
you weigh someone, you will help assure getting an
accurate weight.
SCALE CONTROL PAD OPERATIONS:
ON/ZERO Button: Press before seating
person to be weighted to turn scale on and
zero out weight of previous person.
Important: Immediately after pressing the
ON/ZERO Button you will see a sequence
of three sets of numbers. The first two sets
are service information, and the last set is
the battery life indicator. If the last set of
numbers reads below 5.2 call maintenance
to replace the batteries.
LB/KG Button: Press this button to switch
from lbs. to kg as needed before seating
the next person to be weighted.
RECALL Button: Press this button if you
need to know the weight of the last person
weighted after they have left the chair and
the scale has not been turned on and
zeroed out for the next person to be
weighted.

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 10 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
5. Tub Fill Procedures with Pre-Fill Console:
a. Turn the BathAire(sm) on.
b.Push down on the Close button until the
door is fully closed and stops on its own. You
will no longer hear the motor and the seal
will be compressed.
CAUTION: Prior to closing the door, ensure
NO materials I.E. towels, band aids, etc. are
trapped between door and tub. Make sure
the door comes to a complete stop to
properly seal the tub. Failure to do so may
result in leaks.
c. Close the drain by rotating the Drain Handle.
d.To fill reservoir tub: To fill tub open the
Reservoir Rapid Release or if not using the
prefill Reservoir, Lift Shower Spray out of
holder. Direct spray to inside tub wall. Turn on
shower control valve. Adjust mixing valve for
water temperature of 95 - 105 F or 35 –41 C
displayed on the thermometer. Do not allow
temperature to exceed these levels. Also test
on wrist to make sure it is comfortable & safe.
(See Warnings Below). After adjusting
temperature turn shower control valve off.
Close drain with drain open close lever.Turn fill
control valve on. Continue monitoring the
thermometer to maintain safe temperatures
until tub or Reservoir is filled. The Reservoir
once filled will shut off. If you do not want to
fill the Reservoir turn fill control valve off once
bath is filled
e.If manual fill is desired, do not close and fill
the reservoir.
f. Fill to 2”- 4” below the Drain
Handle/Overflow then turn the Reservoir Fill
Valve off. This allows for resident movement
and Bathaire(SM) action.
g. Press BATH OIL or SHAMPOO button briefly
to initiate pump cycle. If using BATH OIL,
allow it to dispense directly into the bath
water. If using SHAMPOO, hold hand under
the dispensing head inside tub wall. If more
solution is required, press button a second
time. The amount of bath oil and shampoo
dispensed is preset for economic portions at
CONSOLE CONTROLS
Mixing Valve
Reservoir Fill
Control Valve
Door Open
Button
Tub Fill and
Shower
Spray
Shower Spray
Valve
Liquid
Dispensing
Controls
Door Close
Button
Tank Temperature
Thermometer
Incoming Water
Thermometer
Emergency Door
Open Button
Drain Handle/
Overflow
LIQUID DISPENSIG
CONTROLS
Reservoir Fill
Button
Rapid Fill
Button

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 11 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
the factory. If you need more solution, press
the button a second time.
h.If no solution is dispensed from the
dispensing head, open the service door to
access the solutions storage. Check the fluid
level in the one liter bottle. If below the
intake hose, replace with MasterCare’s Bath
Oil or Shampoo per priming instructions
below.
Note:
1. If you press Bath Oil or Shampoo button for more than
five seconds, it will initiate a pump prime cycle.
2. The normal pump cycle can finish and turn off before
the five seconds occurs, but it will still enter Prime and
turn back on.
3. Holding a Button for a longer time will not cause any
problems other than initiating Prime.
4. Pressing any button while a pump is running will shut
off the pump. This is predominately a safety feature for
the Prime operation.
5. Pressing multiple buttons at the same time will turn off
any pumps and be otherwise ignored.
6. A Red LED associated with the pump operation will turn
on when the pump operation is activated.
7. See the maintenance instructions for the purpose and
function of the Green LED.
Replacing One Liter Jugs & Priming Operation:
a. Remove the empty bottle of solutions and replace with
MasterCare’s Bath Oil or Shampoo. Remove the cap and seal
under the cap on the bottle of liquid.
b. Insert the foot strainer attached to the cap with dispensing hose
into the bottle so that the strainer foot is on the bottom of the
bottle. If replacing an empty two-liter container, check the
strainer at the bottom of the strainer. Remove any accumulated
debris that can clog it up.
c. To prime, push appropriate button for the solution you are
priming for seven seconds.
CAUTION: Other brand bath oils and shampoos may be used with
the MasterCare System although re-calibration may be required.
However, some products may not be compatible with the system
and may damage components in the system, thereby voiding the
warranty. MasterCare offers an extended warranty with your use
of MasterCare bathing and Cleaning/disinfection products. Please
contact MasterCare customer service @ 800-798-5867 before using
non-MasterCare products in your system.
SHAMPOO
BOTTLE
BATH OIL
BOTTLE

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 12 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
6. Bathing Procedures:
a. During the normal bath cycle, you can
shampoo the individual’s hair and wash
their body with MasterCare’s specially
formulated Shampoo and Body Wash.
Bathe or assist the individual with their
hygiene needs.
b.To rinse, lift the Shower Spray from its
holder, located on the tub deck, then
direct the nozzle towards the open water
in the tub. Turn the Shower Spray on by
turning the Shower Spray Control Valve
counter clockwise to full open. Adjust the
shower water temperature to the desired
individual comfort level using the Gen II
Mixing Valve. Test the water temperature
on your wrist before showering the
individual. Turn off Shower Spray Control
Valve when complete by turning knob
clockwise. Return Shower Spray to its
holder.
7. End of the Bath Cycle –Drain Tub
At the end of the bath cycle, while leaving
the BathAire(SM) on, open the drain by
rotating the Drain Handle/Overflow to open
position. Allow the tub to drain completely
before opening the door.
Note: Sensors in the tub will prevent the
Open-Door button from functioning while
there is water in the tub. Make sure tub is
completely empty and nothing is touching
the sensor, i.e. foot or wash cloth, etc.
CAUTION: If an emergency arises, press
simultaneously the Emergency Door Open
button and the Door Open button located in
the Foot-End Controls.
8. Open the door by pushing down on the Door Open
Button.
Right after the initial door's rotating movement, stop
opening for three (3) seconds allowing residual water
to dissipate down the Casual Water Drain. Continue to
open the door and allow the door to rotate to a fully
open position until it stops on its own.
9. Press the On/Off button to turn off the BathAire(SM)
system.
CONSOLE CONTROLS
Mixing Valve
Reservoir Fill
Control Valve
Door Open
Button
Console
Controls
Tub Fill and
Shower
Spray
Shower Spray
Valve
Liquid
Dispensing
Controls
Door Close
Button
Reservoir Water
Thermometer
Tub Water
Thermometer
Emergency Door
Open Button
Drain Handle/
Overflow
On/Off
Button
Wave
Button
Less Air/Heat
Button
More Air/Heat
Button
BATHAIRE(SM) CONTROLS
Drain Sensors

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 13 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
10. Dry as much of the individual as you can before removing them from the tub by leaning the individual forward
and towel dry their back side and inside of the tub area behind the individual. Lift each leg and towel dry the
underside of the legs/top of the seat, under legs and feet/foot well area under feet.
11. Move the Individual out of the Tub
12. Finish drying the individual.
13. You are now ready to transfer the individual back to their room or other area appropriate.

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 14 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
CLEANING PROCEDURES
Clean and disinfect the tub and transfer after every bath with
MasterCare Cleaner/Disinfectant as follows:
1. Return transfer chair to the bath, place pads and belts
in the foot well of the bath.
2. Close door, Open drain.
3. Using the shower wand rinse the inside surfaces.
4. Close the drain.
5. Open the dispensing cabinet on the head end of the
bath
6. Turn on the disinfectant (turn knob right) that will
dispense disinfectant through the jets. When there is
approximately one gallon of water and MasterCare
Disinfectant Cleaner in the foot well shut off dispensing
(turn knob upright).
7. Using the long-handled brush, thoroughly scrub the
inside of the bath, transfer chair, belts and pads.
8. Open drain
9. Allow for proper disinfectant contact time (Usually 10
minutes or as recommended by the disinfectant's
manufacturer).
10. Turn on the flush water (turn knob left) run water
through the disinfecting lines in the dispensing box.
Turn off (turn knob upright).
11. Thoroughly rinse all cleaned components of the tub and
transfer chair.
CAUTION Some cleaners, disinfectants and floor strippers contain ingredients that are corrosive or abrasive. These
solutions or compounds may contain chlorine, acid, basic ingredients or abrasives. DO NOT allow such solutions or
compounds to come in contact with your MasterCare equipment. Failure to heed this caution could result in damage to
the equipment and void the warranty.
Note: MasterCare Cleaner/Disinfectant is a special non-abrasive cleaning and disinfecting solution that will not harm the
tub's fiberglass surface. MasterCare’s Disinfectant is a great cleaning solution designed and recommended for use with your
Bathing System.
WARNING For proper use and your safety, please follow the directions set forth by the manufacturer of the
disinfectant.
DISINFECTANT VALVE
To the left for water
flushing.
DISINFECTANT
BOTTLE
DISINFECTANT VALVE
Turn valve to the right
for disinfecting.

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 15 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
BATHAIRE(SM) PURGE CYCLE:
BathAire will automatically turn on after the
bath has been idle for twenty (20) minutes and
run for one (1) minute. This allows the area
around the aerators to completely dry.
Other Considerations:
CAUTION: When not being used, all
Disinfectant Cleaner, Bath Oil and Shampoo
solutions used during the bathing procedures
must be stored in a secure area not accessible
by the patients.
It is recommended that a two person bathing
team be established for each shift with trained
backups. Using the team approach, with one
member transferring the individuals to and
from the bathing area and the other operating
the bathing system, increases the efficiency of
the bathing operations.
It is recommended that the operations wall
chart be posted on the wall next to the control
end of the tub for quick reference by the
operator of the Entree Bath system (One is
provided in the tub starter kit).

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 16 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
EMERGENCY OPEN/CLOSE DOOR PROCEDURES
In the event of a medical emergency where it is
needed to open the door before the tub is totally
empty: hold Emergency Door Open Button and the
Door Open Button at the same time to open the door.
It will overwrite the drain water sensors.
In the event there is a power failure.
1. Open the Electrical Service Access Door
2. Press the Door Open Backup.
GFCI RESET PROCEDURES
All MasterCare bathing systems are equipped with
onboard GFCI’s making them easy to access for your
convenience. In the event a power surge trips the
GFCI, it can be accessed and reset using the following
procedures:
GFCI (Ground Fault Circuit Interrupter) detects and
interrupts electric faults to insure safety to all
individuals
Reset Button: trips and shuts down all power should
a power surge, outage,faulty outlet, lightening etc
have any affect on the tub power system. And will
then be pushed to restore power after a qualified
individual deems itsafe.
Test Button: insures the CGFI is working properly by
allowing clear access for testing.
In the event of a power failure, GFCI will need to be
reset to resume operations.
Open Door Button
Emergency
Open Door Button
GFCI
Located at the
Service End
under the
Service Door

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 17 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
ENTREE BATH TRAINING CHECK LIST
After reviewing the operation and safety instructions in this manual, the Entree Bath can be operated and all components
can be identified
OPERATION:
YES
NO
Position Transfer Chair And Lock The Casters
Secure Individual In The Transfer Chair
Transfer Individual Into The Entree Bath
Close Tub Door With Push Buttons
Close Drain With Open/Close Lever
Adjust Mixing Valve To Desired Temperature
Fill Reservoir Console And Or Tub
Use Liquids As Desired
Use Shower Wand With Shower Wand Control Valve
Open Drain With Open/Close Lever
After Water Is Drained, Open Tub Door With Push Buttons
Transfer Individual Out Of The Entree Bath
Return Individual To Room Or Desired Location
Remove Comfort Pads And Place In Foot Well
Use Disinfectant To Clean Tub, Transfer Chair And Pads
Rinse Disinfectant From The Tub, Transfer Chair And Pads
LOCATE & IDENTIFY:
Operator Controls And Thermoscopic Mixing Vavle
LCD Thermometer Tub Fill and Reservoir Fill
Emergency Door Open And GFCI reset
Liquids Dispensing And Aromatherapy Access Cap & Canister
Wall Chart
Casual Water Drain
Training Date:
Staff:
Supervisor:
Please, make copies of this training checklist for each staff member that will operate the Entree Bath.

Entrée Bath Gen III
OPERATION MANUAL
01-27-2022
Page 18 of 18
450 East 32nd Street PO Box 1022 (68026)
Fremont NE 68025
800-798-5867 Office: 402-564-5867 FAX: [phone]
www.mastercarebath.com
It is recommended that the
operations wall chart be posted on
the wall next to the control end of
the tub for quick reference by the
operator of the GEN III Tub.