Matrix E7XE-03 User manual

E7XE-03 SUSPENSION ELLIPTICAL
SERVICE MANUAL

CHAPTER 1: SERIAL NUMBER LOCATION ........................................................... 1
CHAPTER 2: IMPORTANT SAFETY INSTRUCTIONS
2.1 Read and Save These Instructions............................................................................. 3
2.2 Electrical Requirements ............................................................................................. 4
CHAPTER 3: PREVENTATIVE MAINTENANCE
3.1 Recommended Cleaning Tips .................................................................................... 5
3.2 Check for Damaged Parts ......................................................................................... 5
3.3 Care and Maintenance Instructions ........................................................................... 6
3.4 Touch Screen Care & Cleaning .................................................................................. 7
CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION
4.1 Console Description ................................................................................................... 8
4.2 Workout Setup Steps .................................................................................................. 9
CHAPTER 5: MANAGER MODE
5.1 Manager Mode Overview............................................................................................ 10
5.2 Manager Mode - About Tab......................................................................................... 11
5.3 Manager Mode - Time Tab.......................................................................................... 12
5.4 Manager Mode - Defaults Tab..................................................................................... 12
5.5 Manager Mode - Language Tab.................................................................................. 13
5.6 Manager Mode - TV Tab ............................................................................................. 14
5.7 Manager Mode - Other Tab......................................................................................... 15
CHAPTER 6: ENGINEERING MODE
6.1 Engineering Mode Overview....................................................................................... 16
6.2 Engineering Mode - Calibration Tab............................................................................ 16
6.3 Engineering Mode - Errors Tab................................................................................... 17
6.4 Engineering Mode - Statistics Tab .............................................................................. 17
6.5 Engineering Mode - Clubs Tab.................................................................................... 18
6.6 Engineering Mode - Club ID Tab................................................................................. 18
CHAPTER 7: SERVICE MODE
7.1 Service Mode Overview .............................................................................................. 19
7.2 Service Mode - Setup Tab........................................................................................... 20
7.3 Service Mode - Test Tab ............................................................................................. 21
7.4 Service Mode - Date / Time Tab ................................................................................. 22
7.5 Service Mode - Log Tab.............................................................................................. 22
CHAPTER 8: TROUBLESHOOTING
8.1 Electrical Diagram ...................................................................................................... 23
8.2 Error Codes on the Console ...................................................................................... 26
8.3 LCB LED Indicators .................................................................................................... 27
8.4 Troubleshooting - Display Issues................................................................................ 28
8.5 Troubleshooting - Error 0x04A0.................................................................................. 29
8.6 Troubleshooting - Touch Pad Issues........................................................................... 30
8.7 Troubleshooting - Resistance Issues.......................................................................... 31
8.8 Troubleshooting - Pedals Slipping .............................................................................. 32
8.9 Troubleshooting - Noise Issues................................................................................... 32
8.10 Troubleshooting - Heart Rate Issues .......................................................................... 33
8.11 TV Troubleshooting - Overview................................................................................... 34
8.12 TV Troubleshooting - Picture Fuzzy or Unclear.......................................................... 35
8.13 TV Troubleshooting - TV Will Not Turn On ................................................................. 36
8.14 TV Troubleshooting - Entertainment Keypad Issues .................................................. 37
TABLE OF CONTENTS

III
CHAPTER 9: PART REPLACEMENT GUIDE
9.1 Front Disk Replacement ............................................................................................ 38
9.2 Front Shroud Replacement......................................................................................... 39
9.3 Lower Control Board (LCB) Replacement .................................................................. 42
9.4 Generator Replacement.............................................................................................. 43
9.5 Generator Belt Replacement ...................................................................................... 45
9.6 Drive Belt Replacement .............................................................................................. 46
9.7 Pulley Axle Set Replacement...................................................................................... 47
9.8 Drive Axle Set Replacement ....................................................................................... 48
9.9 Crank Replacement .................................................................................................... 52
9.10 Console Replacement................................................................................................. 53
9.11 Console Overlay & Keypad Replacement .................................................................. 54
9.12 Comsole Mast Handlebar ........................................................................................... 56
9.13 Dual Action Handlebar Replacement .......................................................................... 57
9.14 Foot Pedals Replacement........................................................................................... 58
9.15 Pedal Arm Replacement ............................................................................................. 59
9.16 Link Arm Replacement................................................................................................ 60
9.17 Swing Arm Replacement............................................................................................. 61
9.18 Vertical Stabilizer Replacement .................................................................................. 62
9.19 Incline Arm Cover Replacement ................................................................................. 63
9.20 Handlebar Service Replacement ................................................................................ 64
9.21 Testing the Suspension Elliptical................................................................................. 65
CHAPTER 10: EXPLODED DIAGRAMS
10.1 Suspension Elliptical Specifications ........................................................................... 66
10.2 Assembly Hardware .................................................................................................... 67
10.3 Suspension Elliptical Assembly Steps ....................................................................... 68
10.4 Leveling the Suspension Elliptical............................................................................... 80
10.5 TV Programming Instructions ..................................................................................... 81
CHAPTER 11: SOFTWARE UPGRADE PROCEDURE
11.1 Software Upgrade Procedure ..................................................................................... 84
TABLE OF CONTENTS

1
1.1 SERIAL NUMBER LOCATION
CHAPTER 1: SERIAL NUMBER LOCATION
SERIAL NUMBER LOCATION

2
UNIVERSAL CONSOLE SERIAL NUMBER LOCATION
1.1 SERIAL NUMBER LOCATION - CONTINUED
CONSOLE SERIAL NUMBER LOCATION
CHAPTER 1: SERIAL NUMBER LOCATION

3
This Suspension Elliptical is intended for commercial use. To ensure
your safety and protect the equipment, read all instructions before
operating the MATRIX Suspension Elliptical.
When using an electrical product, basic precautions should always be
followed including the following:
• Anapplianceshouldneverbeleftunattendedwhenplugged
in. Unplugtheunitfromtheoutletwhennotinuseandbefore
puttingonortakingoffanyparts.
• Thisproductmustbeusedforitsintendedpurpose
describedinthisservicemanual. Donotuseother
attachmentsthatarenotrecommendbythemanufacturer.
Attachmentsmaycauseinjury.
• Topreventelectricalshock,neverdroporinsertanyobject
intoanyopening.
• Donotremovetheconsolecovers.Serviceshouldonlybe
donebyanauthorizedservicetechnician.
• Donotcarrythisunitbyit’ssupplycordorusethecordas
 ahandle.
• ClosesupervisionisnecessarywhentheSuspension
Ellipticalisusedbyornearchildrenordisablepersons.
• Donotuseoutdoors.
• Donotoperatewhereaerosol(spray)productsarebeing
usedorwhenoxygenisbeingadministered.
• Todisconnect,turnallcontrolstotheoffposition,then
removetheplugfromtheoutlet.
• Donotusetheequipmentinanywayotherthandesignedor
intendedbythemanufacturer.ItisimperativethatallMatrix
FitnessSystemsequipmentisusedproperlytoavoidinjury.
• Keephandsandfeetclearofmovingpartsatalltimesto
 avoidinjury.
• Unsupervisedchildrenmustbekeptawayfromthisequip
 ment.
• Donotwearlooseclothingwhileontheequipment.
CAUTION! Ifyouexperiencechestpains,nausea,dizziness,or
shortnessofbreath,stopexercisingimmediatelyandconsult
yourphysicianbeforecontinuing.
CAUTION! Anychangesormodificationstothisequipment
couldvoidtheproductwarranty.
2.1 READ AND SAVE THESE INSTRUCTIONS
CHAPTER 2: IMPORTANT SAFETY INSTRUCTIONS

4
GROUNDING INSTRUCTIONS:
The Matrix E7xe-03 Suspension Elliptical must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. The Suspension Elliptical is equipped with a cord having an equipment
grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances. If the user does not follow these grounding instructions, the user could void the Matrix limited
warranty.
DANGER: Improper connection of the equipment grounding conductor can result in the risk of electric shock. Check with a qualified electrician
if the user is in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product if it will not fit the outlet,
have a proper outlet installed by an electrician.
CONSOLE POWER
The Matrix Suspension Elliptical console has a battery that makes it self powered. This means that even if the unit is not plugged in, the
console may still have power for up to 12 hours. If the console power needs to be reset or turned off, press and hold the CHANNEL UP and
CHANNEL DOWN keys for 3-5 seconds until the console turns off. The console power will also need to be reset if settings are changed in
Manager, Engineering, or Service Modes.
2.2 ELECTRICAL REQUIREMENTS
CHAPTER 2: IMPORTANT SAFETY INFORMATION
The Matrix Suspension elliptical can now be self powered. It is recommended that the unit be plugged in for at least 4 hours after initial
installation to charge the battery prior to using the self powered feature. NOTE: If an add on TV (using a bracket) or Virtual Active is added to
the unit, it must be plugged in, or the TV or VA will not operate correctly. If the Suspension elliptical will be plugged in, follow the requirements
below.
MATRIX DEDICATED CIRCUIT/ELECTRICAL REQUIREMENT INFO
All Matrix Suspension Elllipticals require the use of a 15 amp or 20 amp “dedicated circuit,” with a non-looped (isolated) neutral/ground, for the
power requirement. Quite simply this means that each outlet you plug Suspension ellipticals into should not have anything else running on that
same circuit besides other Suspension ellipticals (up to 3 per 15 amp circuit and 4 per 20 amp circuit). The easiest way to verify this is to locate
the main circuit breaker box, and turn off the breaker(s) one at a time. Once a breaker has been turned off, the only thing that should not have
power to it are the Suspension ellipticals in question. No lamps, vending machines, fans, sound systems, or any other item should lose power
when you perform this test.
Non-looped (isolated) neutral/grounding means that each circuit must have an individual neutral/ground connection coming from it, and terminating
at an approved earth ground. You cannot “jumper” a single neutral/ground from one circuit to the next.
In addition to the dedicated circuit requirement, the proper gauge wire must be used from the circuit breaker box, to each outlet that will have the
maximum number of units running off of it. If the distance from the circuit breaker box, to each outlet, is 100 ft or less, then 12 gauge wire may be
used. For any distance greater than 100 ft from the circuit breaker box to the outlet, 10 gauge wire must be used.
For your safety and Suspension elliptical performance, the ground on this circuit must be non-looped. Please refer to NEC article 210-21 and 210-23.
Your Suspension elliptical is provided with a power cord with a plug listed below and requires the listed outlet. Any alterations of this power cord
could void all warranties for this product. Multiple Suspension ellipticals can be powered on one dedicated circuit. (3 units per 15 Amp and 4 units
per 20 Amp dedicated circuit.)

5
3.1 RECOMMENDED CLEANING TIPS
Preventative maintenance and daily cleaning will prolong the life and
look of your MATRIX Suspension Elliptical.
Please read and follow these tips.
• Positiontheequipmentawayfromdirectsunlight.TheintenseUV
light can cause discoloration on plastics.
• Locateyourequipmentinanareawithcooltemperaturesandlow
humidity.
• Cleanwithasoft100%cottoncloth.
• Cleanwithsoapandwaterorothernon-ammoniabasedallpur-
pose cleaners.
• Wipefootpads,handles,heartrategrips,andhandlebarsclean
after each use.
• Donotpourliquidsdirectlyontoyourequipment.Thiscancause
damage to the equipment and in some cases electrocution.
• Checkpedalmotionandstability.
• Adjustlevelingfeetwhenequipmentwobblesorrocks.
• Maintainacleanareaaroundequipment,freefromdustanddirt.
DO NOT use any equipment that is damaged or has worn or broken
parts. Use only replacement parts supplied by Matrix Fitness
Systems.
MAINTAIN LABELS AND NAMEPLATES. Do not remove labels
for any reason. They contain important information. If unreadable or
missing, contact Matrix Fitness Systems for a replacement. 1-866-
693-4863, www.matrixfitness.com
MAINTAIN ALL EQUIPMENT Preventative maintenance is the key
to smooth operating equipment. Equipment needs to be inspected
at regular intervals. Defective components must be replaced
immediately. Improperly working equipment must be kept out of use
until it is repaired. Ensure that any person(s) making adjustments
or performing maintenance or repair of any kind is qualified to do
so. Matrix Fitness Systems will provide service and maintenance
training at our corporate facility upon request or in the field if proper
arrangements are made.
3.2 CHECK FOR DAMAGED PARTS
CHAPTER 3: PREVENTATIVE MAINTENANCE

6
3.3 CARE AND MAINTENANCE INSTRUCTION
In order to maximize life span, and minimize down time, all MATRIX equipment requires regular cleaning, and maintenance items performed on
a scheduled basis. This section contains detailed instructions on how to perform these items, the frequency of which they should be done, and a
check list to sign off each time service is completed for a specific machine. Some basic tools and supplies will be necessary to perform these tasks
which include (but may not be limited to):
* Metric Allen wrenches
* #2 Phillips head screwdriver
* Adjustable wrench
* Torque wrench (capability to read foot lbs, and inch lbs)
* Lint free cleaning cloths
* Teflon based spray lubricant
* Mild, water soluble, detergent – such as “Simple Green”, or other Matrix approved product
* Teflon based spray lubricant such as “Super Lube”, or other Matrix approved product
* Vacuum cleaner with an extendable hose and crevasse tool attachment
You may periodically see addendums to this document, as the Matrix Technical Support Team identifies items that require specific attention, the
latest version will always be available on the Matrix web site, www.matrixfitness.com
DAILY MAINTENANCE ITEMS
1) Look and listen for loose fasteners, unusual noises, and any other indications that the equipment may be in need of service.
2) Clean the Suspension Elliptical before and after each use, including:
a. Use a damp, soft cloth with water or mild liquid detergent to clean all exposed surfaces. DO NOT use ammonia, chlorine, or any acid
based cleaners. NOTE: Never spray cleaner directly on the equipment. Spray the cleaner directly into a cloth to clean.
b. Keep the console display free of fingerprints and salt build up caused by sweat.
c. Frequently vacuum the floor beneath the unit to prevent the accumulation of dust and dirt which can affect the smooth operation of the
unit.
3) Attempt to wobble the unit back and forth, level if needed (see Section 10.4).
MONTHLY MAINTENANCE ITEMS
1) Inspect the console, handrails, link arms, pedal arms, and pedals for damage.
2) Check the link / pedal arms for loose joints, tighten hardware as needed.
3) Adjust leveling feet if the equipment rocks or wobbles.
4) Check the pedal foot pad for damage or wear. Replace as needed. Vacuum under the rubber foot pad.
QUARTERLY MAINTENANCE ITEMS
1) Remove the front shrouds and check belts for damage, alignment, and proper tension.
2) Remove the plastic covers where the handlebar and link arms are connected. Lubricate the ball joint with your finger by applying grease to
the ball bearing.
CHAPTER 3: PREVENTATIVE MAINTENANCE

7
3.4 TOUCH SCREEN CARE & CLEANING
TOUCH SCREEN CARE AND CLEANING
* The touch screen requires very little maintenance. We recommend that you periodically clean the touch screen surface with a dry soft cloth.
If necessary, we recommend the usage of Alcohol or Isopropyl Alcohol for difficult stains or sanitary purposes.
* It is very important to avoid using any other chemical on the touch screen.
* Always dampen the cloth and clean the screen. Do not spray the cleaning agent on the screen itself, the drips can seep into the display or
stain the bezel.
* After cleaning, make sure the surface is dry. There should not be any left over solvent to seep into the display.
* It is very important to handle the touch screen with care. Do not use excessive force when cleaning.
* Do not use any sharp materials to clean the touch screen surfaces.
* Do not use high pressure air, water, or steam to clean the touch screen surface.
CHAPTER 3: PREVENTATIVE MAINTENANCE

8
4.1 CONSOLE DESCRIPTION
The E7xe has a fully integrated touch screen display. All information required for workouts is explained on screen. Exploration of the interface is
highly encouraged. The information explaining how to program for various workouts will give an explanation about the contents of each screen on
the machine.
E7XE-03 ENTERTAINMENT ZONE
IPOD®: Will take the user directly to the iPod screen to allow for iPod control and play list selection.
VOLUME UP / DOWN: Adjusts the volume output through the headphone jack of either integrated console TV or iPod output.
NUMBERKEYPAD: Allows for easy TV channel selections.
CHANNEL UP / DOWN: Allows for channel selection.
DISPLAY MODE: Allows user to cycle through console display options, iPod, TV, or profile display.
LAST CHANNEL: Allows the user to cycle between the current channel and the previous channel they were viewing.
CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION

9
To set up a workout, press the touch screen over the program you would like to use and then follow the prompts to begin your workout.
GO - Press to immediately begin a workout. Workout, resistance level, and time will automatically go to default settings. Pressing GO will not
prompt user for age, weight, or level settings.
MANUAL - Manual allows the user to input more information while defining their own workout. Calorie expenditure will be more accurate when
inputting information in Manual than by pressing GO.
FAT BURN - Fat burn is a level based program that is designed to help users burn fat through various resistance level changes.
ROLLING HILLS - The Rolling Hills program is a level based program that automatically adjusts the resistance level to simulate real terrain.
INTERVALS - The Intervals program is a level based program that automatically adjusts the resistance of the machine from low to high
intensity settings at regular intervals.
RANDOM - Random is a level based workout that randomly adjusts the resistance of the machine.
TARGET HEART RATE - The Matrix Suspension Elliptical comes with standard digital contact heart rate sensors and are POLAR
telemetry compatible. The heart rate control workout mode allows the user to program their desired heart rate zone, and the Suspension
Elliptical will automatically adjust the level based upon the user's heart rate. The heart rate zone is calculated using the following equation:
(220-Age)8%=targetheartratezone.TheusermustwearaPOLARtelemetricstraporcontinuallyholdontothecontactheartrategripsforthis
workout.
Locate the metal sensors on the handlebars of the Suspension Elliptical. Notice that there are two separate pieces of metal on each grip. You
must be making contact with both pieces of each grip to get an accurate heart rate reading. You can grab these sensors in any program to view
your current heart rate.
FITNESS TEST -The Cooper Fitness Test measures cardiovascular fitness and proves an estimated sub-maximal VO2 result. It is based on
power output according to ACSM standards and was developed by the Cooper Institute© (www.cooperinstitute.org). User RPMs must remain
between 60-80 RPM during the test. The test will end when the user can no longer maintain this speed. Use of a heart rate strap is optional but
provides more data.
The test starts at a low intensity level and gradually increases in intensity (difficulty) every 2 minutes. As it increases, the user must maintain
60-80 RPM to advance to the next level. The test could take upwards of 30+ minutes for very fit individuals. Once the test ends a recovery period
(cool down) will begin and the user's results are calculated and displayed. Results are based on the number of stages completed. Incline will not
be adjustable during the test.
STAGE COMPLETE:
1 Well Below Average
2 Well Below Average
3 Below Average
4 Below Average
5 Average
6 Average
7 Above Average
8 Above Average
9+ Well Above Average
CONSTANT WATTS - Constant Watts is a unique program that allows you to vary your cadence or RPM and the Suspension Elliptical's
resistance level will adjust accordingly to your selected goal. The quicker you pedal, the less resistance for the goal selected.
4.2 WORKOUT SETUP STEPS
CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION

10
The Manager's Custom Mode allows the club owner to customize the Suspension Elliptical for the club.
1) To enter Manager Mode, press ENTER, 1, 0, 0, 1, ENTER on the lower display. Manager Mode will appear on the display (Figure A).
2) Follow the prompts to change the desired setting.
3) Press the ENTER key once the desired setting is correct to save.
4) Press HOME to return to normal operation. NOTE: If a setting has been changed, the unit and console power should be reset. Cycle the
power switch, and press and hold the CHANNEL UP and CHANNEL DOWN keys for 3-5 seconds to reset the console power.
5.1 MANAGER MODE OVERVIEW
FIGURE A
CHAPTER 5: MANAGER MODE

11
5.2 MANAGER MODE - ABOUT TAB
MANAGER MODE
About
FUNCTION & DEFAULTS DESCRIPTIONS MODIFIED
Serial Number This option displays the serial number of the
platform and console. See Service Mode to
edit the serial numbers.
Cannot be modified.
Accumulated Distance Total distance on the unit since production. Cannot be modified.
Accumulated Time Total time on the unit since production. Cannot be modified.
Software Versions Software version. Cannot be modified.
Out of Order
Default: Off
This option allows the club to show the unit
"out of order" if an error is present.
On / Off
CSafe Model Default: On This option controls whether the console is
Fitlinxx compatible.
On / Off
E7xe-03-C - If the unit has the LMM board, the CSafe
Model should be set for On. The Suspension Style
Elliptical uses this console.
CHAPTER 5: MANAGER MODE
E7xe-02-C or E7xe-01-C - If the unit has the old MMM
board, the CSafe Model should be set for Off (even if
the MMM console is replaced).

12
5.3 MANAGER MODE - TIME TAB
FUNCTION & DEFAULTS DESCRIPTIONS MODIFIED
Max Time Default: 60 Minutes This option allows the club to set the maximum workout
duration limits during peak and non peak hours.
Maximum: 99 Minutes
Minimum: 5 Minutes
Default Time Default: 30 Minutes This option controls the default program time. Max: Max Time Min: 5 Min
Pause Time Default: 5 Minutes This option controls the default pause time. Max: 10 Min Min: 1 Min
MANAGER MODE
Time
FUNCTION & DEFAULTS DESCRIPTION MODIFIED
Level Default: 1 This option controls the default program level. Max: 1 Min: 20
Age Default: 30 This option controls the default user's age used in the target HR
calculations.
Maximum: 100
Minimum: 10
Weight Default: 150 lbs
/ 68 kg
This option controls the default weight used in the calorie
calculations. Displayed in pounds or kilograms.
Maximum: 400 lbs / 182 kg
Minimum: 50 lbs / 22 kg
Gender Default: Male Setting the user as Male or Female. Male or Female
Key Sound Default: Yes This option allows different sounds to be chosen for the keypad. Yes or No
MANAGER MODE
Defaults
5.4 MANAGER MODE - DEFAULTS TAB
CHAPTER 5: MANAGER MODE

13
5.5 MANAGER MODE - TV TAB
MANAGER MODE
TV
FUNCTION & DEFAULTS DESCRIPTIONS MODIFIED
Default Channel
Default: 3
This option controls the default TV channel
on start up.
Channels 1-999
Default Volume
Default: 5
This option controls the default TV volume
on start up.
Maximum: 17
Minimum: 1
Tuner Available Default: Yes This option controls the default TV function. Yes or No
Setup This option is used to set the TV tuner
function. Press the "-: key to enter this
function.
CHAPTER 5: MANAGER MODE

14
5.6 MANAGER MODE - LANGUAGE TAB
MANAGER MODE FUNCTION & DEFAULTS DESCRIPTIONS MODIFIED
Language Select default language. This option allows the user to select a flag for a
specific language.
N/A
FLAG UNIT
Mile
Mile
KM
KM
KM
LANGUAGE
English
German
FLAG UNIT
KM
KM
KM
KM
KM
LANGUAGE
Spanish
Dutch
Italian
Japanese
FLAG UNIT
KM
KM
KM
KM
KM
LANGUAGE
Chinese
Portuguese
French
CHAPTER 5: MANAGER MODE

15
FLAG UNIT
KM
KM
KM
KM
KM
5.7 MANAGER MODE - ABOUT TAB
FUNCTION & DEFAULTS DESCRIPTIONS MODIFIED
Asset Management
Default: Off
This option allows fitness clubs to collect workout
data to a PC.
On or Off
Virtual Active
Default: Off
This option control the Virtual Active function. On or Off
ENGINEERING MODE
Other
CHAPTER 5: MANAGER MODE

16
6.1 ENGINEERING MODE OVERVIEW
The Engineering Mode allows the club owner to keep track of the technical settings and error history for the Suspension Elliptical.
1) To enter Engineering Mode, press ENTER, 2, 0, 0, 1, ENTER on the lower display. Engineering Mode will appear on the display (Figure A).
2) Follow the prompts to change the desired setting.
3) Press the ENTER key once the desired setting is correct to save.
4) Press HOME to return to normal operation. NOTE: If a setting has been changed, the unit and console power should be reset. Cycle the
power switch, and press and hold the CHANNEL UP and CHANNEL DOWN keys for 3-5 seconds to reset the console power.
FIGURE A
ENGINEERING MODE
Calibration
6.2 ENGINEERING MODE - CALIBRATION TAB
FUNCTION & DEFAULTS DESCRIPTIONS MODIFIED
RPM Low Limit Charge:
Default: 10
This option controls the RPM low limit to iPod
charge.
Range: 0 - 255
RPM Low Limit Resistance
Default: 10
This option control the RPM low limit to show
resistance.
Range: 0 - 255
CHAPTER 6: ENGINEERING MODE

17
ENGINEERING MODE FUNCTION & DEFAULTS DESCRIPTIONS MODIFIED
Statistics This option displays the workout
information for the unit.
N/A
6.3 ENGINEERING MODE - STATISTICS TAB
ENGINEERING MODE FUNCTION & DEFAULTS DESCRIPTIONS MODIFIED
Errors This option displays the error code
history for the unit.
N/A
6.4 ENGINEERING MODE - ERRORS TAB
CHAPTER 6: ENGINEERING MODE