Matsing MS-12C45 User manual

TABLE OF CONTENTS:
BEAMS & CONNECTORS:
Plan View Resultant Beam Direction
Plan View Connector Layout
Connector Ports Table
BEAM PATTERN
Vertical Beam Pattern (Top & Bottom Row)
Horizontal Beam Pattern (Top Row)
Horizontal Beam Pattern (Bottom Row)
TRANSPORTATION / INSTALLATION
Transportation (From Point to Point)
Bracket Mounting
Installation using a crane
Lifting the Antenna
Antenna Installation
Antenna Leveling
Digital Level Gauge Calibration
Adjustment Requirement
Revision History:
[email protected] www.matsing.com 1 / 6
email:
website:
Page
Revision
nos.
3.41
3.42
3.43
Date
Description
Revised by
3.00
3.10
3.20
3.30
3.31
3.40
1.20
1.30
2.00
2.10
2.20
2.30
Pavel
MS-12C45-IM-001
0
INSTRUCTION MANUAL MS-12C45
1.00
1.10
MS-12C45
Instruction Manual
Date
Prepared by
Approved by
Document nos
Revision
1 Jul 2022
Ray Ling

BEAMS & CONNECTORS:
Plan View Resultant Beam Direction
Plan View Connector Layout
Connector Ports Table
2 / 6
Page
(+45˚)
(-45˚)
(+45˚)
(-45˚)
(+45˚)
(-45˚)
(+45˚)
(-45˚)
(+45˚)
(-45˚)
(+45˚)
(-45˚)
PORT 17
PORT 18
PORT 15
PORT 16
PORT 13
PORT 14
PORT 23
PORT 24
PORT 21
PORT 22
PORT 19
PORT 20
BEAM 12
BEAM 11
BEAM 10
BEAM 9
BEAM 8
BEAM 7
(-45˚)
(+45˚)
(-45˚)
(+45˚)
(-45˚)
Bottom Row
PORT 4
PORT 1
PORT 2
(+45˚)
(-45˚)
(+45˚)
(-45˚)
(+45˚)
(-45˚)
(+45˚)
BEAM 1
PORT 11
PORT 12
PORT 9
PORT 10
PORT 7
PORT 8
PORT 5
PORT 6
PORT 3
1.00
1.10
1.20
1.30
Top Row
BEAM 6
BEAM 5
BEAM 4
BEAM 3
BEAM 2
0˚
BEAM 1 - 6
(Top Row)
Frequency: 3700 - 4200 MHz
Plan View Resultant Beam Directions
BEAM 7 - 12
(Bottom Row)
PLAN VIEW CONNECTOR LAYOUT
MS-12C45

BEAM PATTERN
Vertical Beam Pattern (Top & Bottom Row)
Horizontal Beam Pattern (Top Row)
Horizontal Beam Pattern (Bottom Row)
3 / 6
Page
2.00
2.10
2.20
2.30

TRANSPORTATION / INSTALLATION
Transportation (From Point to Point)
Bracket Mounting
4 / 6
Strictly comply to the Local authority and regulatory on Workplace Safety and Health Control and
Measure when moving and transportation of large or heavy equipment, appropriate material
handling machine should be use.
(Risk Assessment apply for Forklift or Pallet Truck Lifting)
Page
Item
Lens/Types
Holes Size
Bracket Qty
OPEN end bolt & nuts sets
1
30cm to 120cm
Ø13mm x 8
4
M12 x 15cm=8sets
3.00
3.10
3.20
455.4
Attached the
bracket tighten with
specified bolts sets.
Important Notes:
End User is require
to
Custom-Make
the additional
supporting bracket
and tighten to the
existing Antenna
bracket to meet the
deployment needs.
444.1

Installation using a crane
Lifting the Antenna
5 / 6
The antenna has 2 hook points installed on the top frame (located slightly behind the center of the
sphere). These hooks are designed at the center of gravity point of the antenna. A cable, rope can be
securely fastened to the hooks and the antenna can be lifted using a crane as pictured below.
Page
3.30
Strictly comply to the local authority and regulatory on Workplace Safety and Health Control and
Measure when performing lifting of large or heavy equipment, appropriate material handling
machine should be used and only certified personnel should perform the task.
(Risk Assessment requirement applies for both Up-Lifting and Down-Lifting.)
3.31

Antenna Installation
Antenna Leveling
Digital Level Gauge Calibration
Adjustment Requirement
6 / 6
3.43
Page
3.40
With reference to Item Bracket Mounting Procedure, End user is required to Custom-Make the
additional supporting bracket and tighten it to the existing Antenna bracket to meet the deployment
needs.
3.41
After the Antenna is mounted to the bracket, it is required to be adjusted to 0˚ (Zero Degree) with
≤0.2˚ on 3 sides of the frame top level.(Rear, Right & Left=As shown in picture)
3.42