Matsing MS-6H90 User manual

TABLE OF CONTENTS:
BEAMS & CONNECTORS:
Plan View Resultant Beam Direction
Plan View Connector Layout
Connector Ports Table
PATTERN DIAGRAM
Horizontal Beam Pattern
Vertical Beam Pattern
TILT ADJUSTMENT / RET INSTALLATION or REPLACEMENT PROCESS
Manual Tilt Adjustment
RET Installation / Replacement Process (Reverse for Uninstallation)
RET Controller Display
RET Discover and Active
Beam 1-6 Operations Display
TRANSPORTATION / INSTALLATION
Transportation (From Point to Point)
Bracket Mounting
Installation using a crane
Lifting the Antenna
Antenna Installation
Antenna Leveling
Digital Level Gauge Calibration
Adjustment Requirement
Revision History:
[email protected] www.matsing.com 1 / 8
Patrick Yeo
MS-6H90-IM-001
2
INSTRUCTION MANUAL MS-6H90
MS-6H90
Instruction Manual
Date
Prepared by
Approved by
Document nos
Revision
10 Nov 2023
Ray Ling
10-Nov-23
Include RET Controller Display & Add RET Replacement /
Installation Caution Point
Ray Ling
2
Revised by
Revision
nos.
21-Sep-21
Revised mounting bracket types of bolts and nuts sets use
and general updates.
Ray Ling
1
Date
Description
email:
website:
Page
2.20
3.00
3.10
3.20
4.00
4.10
1.00
1.10
1.20
1.30
2.00
2.10
5.40
5.41
5.42
5.43
4.20
5.00
5.10
5.20
5.30
5.31

BEAMS & CONNECTORS:
Plan View Resultant Beam Direction
Plan View Connector Layout
Connector Ports Table
2 / 8
1.30
BEAM 6
BEAM 5
BEAM 4
BEAM 3
BEAM 2
1.00
1.10
1.20
BEAM 1
PORT 11
PORT 12
PORT 9
PORT 10
PORT 7
PORT 8
PORT 5
PORT 6
PORT 3
(-45
Page
PORT 4
PORT 1
PORT 2
(+45
(-45
(+45
(-45
(+45
(-45
(+45
(-45
(+45
(-45
(+45
PLAN VIEW CONNECTOR LAYOUT
MS-6H90

Frequency: 1695 MHz
Plan View Resultant Beam Directions

PATTERN DIAGRAM
Horizontal Beam Pattern
Vertical Beam Pattern
TILT ADJUSTMENT / RET INSTALLATION or REPLACEMENT PROCESS
Manual Tilt Adjustment
3 / 8
2.00
2.10
Page
3.00
3.10
2.20
Step 1:
Tilt Stopper Loosening
Step 2:
Adjusting the Tilt
Step 3:
Tilt Stopper Tightening

RET Installation / Replacement Process (Reverse for Uninstallation)
4 / 8
3.20
Page
Step 1: Uninstall the shaft
stopper
Step 2: Uninstall the shaft
Handle
Step 3: Install the Hex
adaptor and screw it on
Step 4: Install the RET
attachment interface
Step 5: RET Actuator stub
gap facing out Step 6: RET Tighten to
attachment interface
Step 8: RET Actuator
installation complete.
Repeat the same
process for other
actuator installation.
Step 7: Screw and tighten
RET cable
1. Do not apply any rotation
force to the cable
2. Carefully align same direction
to the keyway before insertion.
3. Insert direct (not angular)
until well fully seated before
turning.
4. Once both thread is fit can
start slowly turning.
5. Tighten the AISG connector
by hand only.
6. If use torque wrench do not
exceed 1.1 Nm (0.8 ft if) torque.
.
Step 7 CAUTION
ADVICE:
** Replace the AISG
cable if is faulty.
** Same caution apply

RET Controller Display
RET Discover and Active
Beam 1-6 Operations Display
5 / 8
Page
4.00
4.10
4.20
Model/Serial no./Beam No.

TRANSPORTATION / INSTALLATION
Transportation (From Point to Point)
Bracket Mounting
6 / 8
5.00
Page
5.10
5.20
1
30cm to 120cm
Ø13mm x 8
4
M12 x 15cm=8sets
Strictly comply to the Local authority and regulatory on Workplace Safety and Health Control and
Measure when moving and transportation of large or heavy equipment, appropriate material handling
machine should be use.
(Risk Assessment apply for Forklift or Pallet Truck Lifting)
Item
Lens/Types
Holes Size
Bracket Qty
Bolt & nuts sets
Important Notes:
End User is require
to
Custom-Make
the additional
supporting bracket
and tighten to the
existing Antenna
bracket to meet
the deployment
needs.
Attached the
bracket tighten
with specified bolts
sets.

Installation using a crane
Lifting the Antenna
7 / 8
5.30
Page
(Risk Assessment requirement applies for both Up-Lifting and Down-Lifting.)
5.31
The antenna has 2 hook points installed on the top frame (located slightly behind the center of the
sphere). These hooks are designed at the center of gravity point of the antenna. A cable, rope can be
securely fastened to the hooks and the antenna can be lifted using a crane as pictured below.
Strictly comply to the local authority and regulatory on Workplace Safety and Health Control and
Measure when performing lifting of large or heavy equipment, appropriate material handling machine
should be used and only certified personnel should perform the task.

Antenna Installation
Antenna Leveling
Digital Level Gauge Calibration
Adjustment Requirement
8 / 8
Page
5.40
With reference to "Bracket Mounting Procedure", End user is required to Custom-Make the additional
supporting bracket and tighten it to the existing Antenna bracket to meet the deployment needs.
5.41
After the Antenna is mounted to the bracket, it is required to be adjusted to 0˚ (Zero Degree) with
≤0.2˚ on 3 sides of the frame top level.(Rear, Right & Left=As shown in picture)
5.43
5.42