Matsing MS-MBA-3-C4A3 User manual

TABLE OF CONTENTS:
BEAMS & CONNECTORS:
Plan View Resultant Beam Layout
Connector Ports Table
Connector Detail
Connector Layout
PATTERN DIAGRAM
Horizontal Pattern
Vertical Pattern
MANUAL TILT ADJUSTMENT
BRACKET INSTALLATION
Bolts & Nuts Requirements
Tools Requirement
Adjustable Spanner
M12 Spanner
Bracket Spacing & Installation Sample
Revision History:
[email protected] www.matsing.com 1 / 5
email:
website:
Page
Revision
nos.
Date
Description
Revised by
4.30
3.00
4.00
4.10
4.21
4.20
4.22
1.20
1.30
1.40
2.00
2.10
2.20
Pavel
MBA-3-C4A3-IM-001
0
INSTRUCTION MANUAL MS-MBA-3-C4A3
1.00
1.10
MS-MBA-3-C4A3
Instruction Manual
Date
Prepared by
Approved by
Document nos
Rev
24 Jun 2021
Ray Ling

BEAMS & CONNECTORS:
Plan View Resultant Beam Layout Connector Layout
Connector Ports Table
Connector Detail
2 / 5
(-45˚)
(-45˚)
BEAM 2
Port 7
(+45˚)
Port 8
(-45˚)
Port 5
(+45˚)
Port 6
(-45˚)
BEAM 3
Port 11
(+45˚)
1.30
1.40
Page
Port 12
(-45˚)
Port 9
(+45˚)
Port 10
(+45˚)
Port 2
(-45˚)
Port 1
(+45˚)
Port 4
BEAM 1
Port 3
1.00
1.10
1.20
0
BEAM 2
BEAM 2
Plan View Resultant Beam Directions
Frequency: 3700 MHz
AISG IN
FB Beams: 1,2,3
FB Ports: 1 to 12
REAR VIEW CONNECTOR LAYOUT
MS-MBA-3-C4A3
BEAM 1BEAM 2BEAM 3
Port 3 (+45)
Port 1 (+45)
Port 2 (-45)
Port 4 (-45)
Port 6 (-45)
Port 5 (+45)
Port 12 (-45)
Port 10 (-45)
Port 9 (+45)
Port 11 (+45)
Port 7 (+45)
Port 8 (-45)

PATTERN DIAGRAM
Horizontal Pattern
Vertical Pattern
3 / 5
2.10
2.20
2.00
Page
BEAM 2
3700 - 4200 MHz
Frequency:
MS-MBA-3-C4A3


3700 - 4200 MHz
Frequency:
MS-MBA-3-C4A3

MANUAL TILT ADJUSTMENT
BRACKET INSTALLATION
Bolts & Nuts Requirements
All MBA's Antenna
Bolts & Nuts
Bracket
4 / 5
M12
10
4.11
4.12
Bolts
Nuts
Qty
Size
Qty
Size
Qty
4.00
4.10
Bracket
Page
2
M12 x
200mm
4
2
By Default the knob is on engaged mode, pull out the handle for manual tilt
adjustment, turn the handle to change the tilt.
3
When done, push the handle back in, screw the waterproof cap back to the position.
3.00
1
The MBA antenna come in RET mode as default, but if needed can also be manually
adjusted. To do so, please unscrew the waterproof cap behind the element whose
tilt is to be adjusted.
1. Engaged with
internal RET motor
position
2. Unscrew/
Screw the cap for tilt
adjustment process
3. Pull knob out to
disengaged RET for
tilt adjustment
Tilt
Adjustment
Knob
Angle
Indicator
RET
Controller

Tools Requirement
Adjustable Spanner
M12 Spanner
Bracket Spacing & Installation Sample
5 / 5
4.30
Page
4.20
4.21
4.22