Matsing MS-MBA-3-H8A2 User manual

TABLE OF CONTENTS:
BEAMS & CONNECTORS:
Plan View Resultant Beam Layout
Connector Port Table
Connector Detail
Connector Layout
PATTERN DIAGRAM
H-Band Horizontal Pattern
H-Band Vertical Pattern
MANUAL TILT ADJUSTMENT
BRACKET INSTALLATION
Bolts & Nuts Requirements
Bolts & Nuts
Bracket
Tools Requirement
M12 Spanner
Adjustable Spanner
Bracket Spacing & Installation Sample
Revision History:
[email protected]
www.matsing.com
1 / 6
4.21
Date
Description
3.00
email:
website:
Page
Revised
by
Revision
nos.
2.10
2.20
Pavel
MBA-3-H8A2-001
0
INSTRUCTION MANUAL MS-MBA-3-H8A2
1.00
1.10
MS-MBA-3-H8A2
Instruction Manual
Date
Prepared by
Approved by
Document nos
Rev
21 Apr 2023
Ray Ling
4.00
4.10
4.11
4.12
4.20
4.22
4.30
1.20
1.30
1.40
2.00

BEAMS & CONNECTORS:
Plan View Resultant Beam Layout
Connector Port Table Connector Detail
2 / 6
Page
Port 19
Port 11
Port 3
(+45˚)
(+45˚)
(+45˚)
Port 20
Port 12
Port 4
(-45˚)
(-45˚)
(-45˚)
(-45˚)
(-45˚)
(-45˚)
BEAM 3
BEAM 2
BEAM 1
Port 23
Port 15
Port 7
(+45˚)
(+45˚)
(+45˚)
Port 22
Port 14
Port 6
Port 24
Port 16
Port 8
(-45˚)
(-45˚)
(-45˚)
Port 21
Port 13
Port 5
1.30
1.00
1.10
1.20
(+45˚)
(+45˚)
(+45˚)
Port 17
Port 9
Port 1
(+45˚)
(+45˚)
(+45˚)
Port 18
Port 10
Port 2
(-45˚)
(-45˚)
(-45˚)

BEAM 2
Frequency: 1695 MHz
Plan View Resultant Beam Directions
BEAM 2

Connector Layout
3 / 6
Page
1.40
REAR VIEW CONNECTOR LAYOUT
MS-MBA-3-H8A2
Port 7 (+45˚)
Port 8 (-45˚)
Port 15 (+45˚)
Port 16 (-45˚)
Port 23 (+45˚)
Port 24 (-45˚)
Port 5 (+45˚)
Port 6 (-45˚)
Port 13 (+45˚)
Port 14 (-45˚)
Port 21 (+45˚)
Port 22 (-45˚)
Port 3 (+45˚)
Port 4 (-45˚)
Port 11 (+45˚)
Port 12 (-45˚)
Port 19 (+45˚)
Port 20 (-45˚)
Port 1 (+45˚)
Port 2 (-45˚)
Port 9 (+45˚)
Port 10 (-45˚)
Port 17 (+45˚)
Port 18 (-45˚)
BEAM 1BEAM 2BEAM 3
AISG IN-1
HB Beam: 1
HB Ports: 1 to 8
AISG IN-2
HB Beam: 2
HB Ports: 9 to 16
AISG IN
HB Beam: 3
HB Ports: 17 to 24

PATTERN DIAGRAM
H-Band Horizontal Pattern
H-Band Vertical Pattern
4 / 6
2.00
2.10
Page
2.20



1695 -2690 MHz
Frequency:
MS-MBA-3-H8A2

BEAM 2
MS-MBA-3-H8A2 1695 -2690 MHz
Frequency:

MANUAL TILT ADJUSTMENT
5 / 6
2
By Default the knob is on engaged mode, pull out the handle for manual tilt
adjustment, turn the handle to change the tilt.
3
When done, push the handle back in, screw the waterproof cap back to the
position.
Page
3.00
1
The MBA antenna come in RET mode as default, but if needed can also be
manually adjusted. To do so, please unscrew the waterproof cap behind the
element whose tilt is to be adjusted.
Tilt
Adjustment
Knob
Angle
Indicator
RET
Controller

BRACKET INSTALLATION
Bolts & Nuts Requirements
Bolts & Nuts Bracket
Tools Requirement Adjustable Spanner
M12 Spanner
Bracket Spacing & Installation Sample
6 / 6
Page
4.30
4.11
4.12
4.10
Bracket Qty
2
4.21
4.20
4.22
4.00
Bolts Qty
4
Nut Size
Nut Qty
M12
10
Bolts Size
M12 x 200mm
135
mm