Matsing MS-16F60 User manual

TABLE OF CONTENTS:
BEAMS & CONNECTORS:
Plan View Resultant Beam Direction
Beam 1-8 (Top Row)
Beam 9-16 (Bottom Row)
Plan View Connector Layout
Connector Ports Table
PATTERN DIAGRAM
Vertical Beam Pattern
Horizontal Beam Pattern (Top Row)
Horizontal Beam Pattern (Bottom Row)
TRANSPORTATION / INSTALLATION
Transportation (From Point to Point)
Bracket Mounting
Installation using a crane
Lifting the Antenna
Antenna Installation
Antenna Leveling
Digital Level Gauge Calibration
Adjustment Requirement
Revision History:
[email protected] www.matsing.com 1 / 7
3.30
3.31
3.40
3.41
3.42
3.43
1.00
1.10
1.11
1.12
1.20
1.30
2.00
2.10
2.20
2.30
3.00
3.10
3.20
Date
Description
Revised by
Revision
nos.
email:
website:
Page
Pavel
MS-16F60-IM-001
00
INSTRUCTION MANUAL MS-16F60
MS-16F60
Instruction Manual
Date
Prepared by
Approved by
Document nos
Revision
27 May 2022
Ray Ling

BEAMS & CONNECTORS:
Plan View Resultant Beam Direction
Beam 1-8 (Top Row)
Beam 9-16 (Bottom Row)
2 / 7
1.12
Page
1.11
1.00
1.10
0˚
Plan View Resultant Beam Directions
Frequency: 3300 – 4200 MHz
BEAM 1 to 8 (Top Row)
0˚
Plan View Resultant Beam Directions
Frequency: 3300 – 4200 MHz
BEAM 9 to 16 (Bottom Row)

Plan View Connector Layout
Connector Ports Table
PATTERN DIAGRAM
Vertical Beam Pattern
3 / 7
(+45˚)
(-45˚)
(+45˚)
(-45˚)
PORT 19
PORT 20
PORT 17
PORT 18
(+45˚)
(-45˚)
(+45˚)
(-45˚)
PORT 31
PORT 32
PORT 29
PORT 30
PORT 27
PORT 28
(+45˚)
(-45˚)
(+45˚)
(-45˚)
(+45˚)
(-45˚)
(+45˚)
(-45˚)
(+45˚)
(-45˚)
(+45˚)
(-45˚)
PORT 2
BEAM
16
BEAM
15
BEAM
14
BEAM
13
BEAM
12
BEAM
11
BEAM
10
BEAM
9
Bottom Row
PORT 23
PORT 24
PORT 21
PORT 22
PORT 25
PORT 26
BEAM
1
Top Row
BEAM
8
BEAM
7
BEAM
6
BEAM
5
BEAM
4
BEAM
3
(-45˚)
PORT 15
PORT 16
PORT 13
PORT 14
PORT 11
PORT 12
PORT 9
PORT 10
PORT 7
(+45˚)
(-45˚)
(+45˚)
(-45˚)
(+45˚)
(-45˚)
2.00
2.10
Page
1.30
1.20
(+45˚)
(-45˚)
(+45˚)
(-45˚)
PORT 8
PORT 5
PORT 6
PORT 3
(+45˚)
PORT 4
PORT 1
BEAM
2



Top
Bottom
Front
Rear
Vertical Beam Pattern
Frequency:
3300 - 4200 MHz

Horizontal Beam Pattern (Top Row)
Horizontal Beam Pattern (Bottom Row)
4 / 7
Page
2.20
2.30

Frequency:
3300 - 4200 MHz
Horizontal Beam Pattern
Top Row

Horizontal Beam Pattern
Bottom Row
Frequency:
3300 - 4200 MHz

TRANSPORTATION / INSTALLATION
Transportation (From Point to Point)
Bracket Mounting
5 / 7
(Risk Assessment apply for Forklift or Pallet Truck Lifting)
Bracket Qty
OPEN end bolt & nuts sets
4
M12 x 15cm=8sets
Page
1
30cm to 120cm
Ø13mm x 8
Item
Lens/Types
Holes Size
3.00
3.10
Strictly comply to the Local authority and regulatory on Workplace Safety and Health Control and
Measure when moving and transportation of large or heavy equipment, appropriate material
handling machine should be use.
3.20
Important Notes:
End User is require to Custom-Make the additional supporting bracket and tighten to the
existing Antenna bracket to meet the deployment needs.
Attached the
bracket
tighten with
specified

Installation using a crane
Lifting the Antenna
6 / 7
The antenna has 2 hook points installed on the top frame (located slightly behind the center of the
sphere). These hooks are designed at the center of gravity point of the antenna. A cable, rope can be
securely fastened to the hooks and the antenna can be lifted using a crane as pictured below.
Strictly comply to the local authority and regulatory on Workplace Safety and Health Control and
Measure when performing lifting of large or heavy equipment, appropriate material handling
machine should be used and only certified personnel should perform the task.
3.30
3.31
Page
(Risk Assessment requirement applies for both Up-Lifting and Down-Lifting.)

Antenna Installation
Antenna Leveling
Digital Level Gauge Calibration
Adjustment Requirement
7 / 7
Page
3.40
With reference to Item Bracket Mounting Procedure, End user is required to Custom-Make the
additional supporting bracket and tighten it to the existing Antenna bracket to meet the deployment
needs.
3.41
After the Antenna is mounted to the bracket, it is required to be adjusted to 0˚ (Zero Degree) with
≤0.2˚ on 3 sides of the frame top level.(Rear, Right & Left=As shown in picture)
3.42
3.43