Matsing MS-6F45 User manual

TABLE OF CONTENTS:
BEAMS & CONNECTORS:
Plan View Resultant Beam Direction
Plan View Connector Layout
Connector Ports Table
BEAM PATTERN
Vertical Beam Pattern
Horizontal Beam Pattern
TRANSPORTATION / INSTALLATION
Transportation (From Point to Point)
Bracket Mounting
Installation using a crane
Lifting the Antenna
Antenna Installation
Antenna Leveling
Digital Level Gauge Calibration
Adjustment Requirement
Revision History:
[email protected] www.matsing.com 1 / 6
General update
Revision nos.
1
Revised by
Ray Ling
email:
website:
Page
28-Jul-22
Description
3.42
3.43
Date
3.10
3.20
3.30
3.31
3.40
3.41
1.20
1.30
2.00
2.10
2.20
3.00
Pavel
MS-6F45-IM-001
1
INSTRUCTION MANUAL MS-6F45
1.00
1.10
MS-6F45
Instruction Manual
Date
Prepared by
Approved by
Document nos
Revision
28 Jul 2022
Ray Ling

BEAMS & CONNECTORS:
Plan View Resultant Beam Direction
Plan View Connector Layout
2 / 6
1.00
1.10
1.20
Page
PLAN VIEW CONNECTOR LAYOUT
MS-6F45
0˚
Frequency: 3300 - 4200 MHz
Plan View Resultant Beam Directions

Connector Ports Table
BEAM PATTERN
Vertical Beam Pattern
Horizontal Beam Pattern
3 / 6
2.10
2.20
Page
(-45˚)
(+45˚)
(-45˚)
(+45˚)
(-45˚)
2.00
PORT 4
PORT 1
PORT 2
(+45˚)
(-45˚)
(+45˚)
(-45˚)
(+45˚)
(-45˚)
(+45˚)
BEAM 1
PORT 11
PORT 12
PORT 9
PORT 10
PORT 7
PORT 8
PORT 5
PORT 6
PORT 3
1.30
BEAM 6
BEAM 5
BEAM 4
BEAM 3
BEAM 2

Horizontal Beam Pattern
Frequency:
3300 - 4200 MHz



Frequency:
3300 - 4200 MHz
Vertical Beam Pattern
Top
Bottom
Front
Rear

TRANSPORTATION / INSTALLATION
Transportation (From Point to Point)
Bracket Mounting
4 / 6
1
30cm to 120cm
Ø13mm x 8
4
M12 x 15cm=8sets
Page
(Risk Assessment apply for Forklift or Pallet Truck Lifting)
3.20
Item
Lens/Types
Holes Size
Bracket Qty
OPEN end bolt & nuts sets
3.00
3.10
Strictly comply to the Local authority and regulatory on Workplace Safety and Health Control and
Measure when moving and transportation of large or heavy equipment, appropriate material
handling machine should be use.
Important Notes:
End User is require to Custom-Make the additional supporting bracket and tighten to the
Attached
the bracket
tighten
with
specified
bolts sets.

Installation using a crane
Lifting the Antenna
5 / 6
3.30
Strictly comply to the local authority and regulatory on Workplace Safety and Health Control and
Measure when performing lifting of large or heavy equipment, appropriate material handling
machine should be used and only certified personnel should perform the task.
(Risk Assessment requirement applies for both Up-Lifting and Down-Lifting.)
3.31
The antenna has 2 hook points installed on the top frame (located slightly behind the center of the
sphere). These hooks are designed at the center of gravity point of the antenna. A cable, rope can be
securely fastened to the hooks and the antenna can be lifted using a crane as pictured below.
Page

Antenna Installation
Antenna Leveling
Digital Level Gauge Calibration
Adjustment Requirement
6 / 6
Page
3.40
With reference to Bracket Mounting Procedure, End user is required to Custom-Make the additional
supporting bracket and tighten it to the existing Antenna bracket to meet the deployment needs.
3.41
After the Antenna is mounted to the bracket, it is required to be adjusted to 0˚ (Zero Degree) with
≤0.2˚ on 3 sides of the frame top level.(Rear, Right & Left=As shown in picture)
3.42
3.43