Matsing MS-48C90 User manual

TABLE OF CONTENTS:
BEAMS & CONNECTORS:
Plan View Resultant Beam Direction
Beam 1-12 (Top Row 1) and Beam 25-36 (Third Row 3)
Beam 13-24 (Second Row 2) and Beam 37-48 (Bottom Row 4)
Rear View Connector Layout
Connector Port Table (From Rear View)
BEAM PATTERN
Horizontal Beam Pattern (Row 1 & 3)
Horizontal Beam Pattern (Row 2 & 4)
Vertical Beam Pattern
TRANSPORTATION / INSTALLATION
Transportation (From Point to Point)
Bracket Mounting
Installation using a crane
Lifting the Antenna
Antenna Installation
Antenna Leveling
Digital Level Gauge Calibration
Adjustment Requirement
Revision History:
[email protected] www.matsing.com 1 / 8
2.10
2.20
2.30
email:
website:
Page
Rev nos
3.41
3.42
3.43
Date
Description
Revised by
3.00
3.10
3.20
3.30
3.31
3.40
1.20
1.30
2.00
1.00
1.10
1.11
1.12
Pavel
MS-48C90-IM-001
0
INSTRUCTION MANUAL MS-48C90
MS-48C90
Instruction Manual
Date
Prepared by
Approved by
Document nos
Revision
21 Jun 2023
Ray Ling

BEAMS & CONNECTORS:
Plan View Resultant Beam Direction
Beam 1-12 (Top Row 1) and Beam 25-36 (Third Row 3)
Beam 13-24 (Second Row 2) and Beam 37-48 (Bottom Row 4)
2 / 8
Page
1.00
1.10
1.11
1.12
Frequency: 37MHz
Plan View Resultant Beam Directions
BEAM 25 - 36
(Third Row 3)
BEAM 1 - 12
(Top Row 1)


Frequency: 37MHz
Plan View Resultant Beam Directions
BEAM 37 - 48
(Bottom Row 4)
BEAM 13 - 24
(Second Row 2)

Rear View Connector Layout
3 / 8
1.20
Page
SYMBOLS:
P__=Port numbers


= (- 


Connector Port Table (From Rear View)
Beam 37-48
Beam 25-36
Beam 13-24
Beam 1-12
4 / 8
Page












PORT
12
PORT
10
PORT
8
PORT
6
PORT
4
PORT
2
PORT
24
PORT
22
PORT
20
PORT
18
PORT
16
PORT
14












PORT
11
PORT
9
PORT
7
PORT
5
PORT
3
PORT
1
PORT
23
PORT
21
PORT
19
PORT
17
PORT
15
PORT
13
6
5
4
3
2
1
12
11
10
9
8
7
BEAM
BEAM
BEAM
BEAM
BEAM
BEAM
BEAM
BEAM
BEAM
BEAM
BEAM
BEAM





1.34
PORT
30
PORT
28
PORT
26








PORT
48
PORT
46
PORT
44
PORT
42
PORT
40
PORT
38
PORT
36
PORT
34
PORT
32






PORT
33
PORT
31
PORT
29
PORT
27
PORT
25





15
14
13
PORT
47
PORT
45
PORT
43
PORT
41
PORT
39
PORT
37
PORT
35
BEAM
24
23
22
21
20
19
18
17
16
BEAM
BEAM
BEAM
BEAM
BEAM
BEAM
1.33
BEAM
BEAM
BEAM
BEAM
BEAM












PORT
60
PORT
58
PORT
56
PORT
54
PORT
52
PORT
50
PORT
72
PORT
70
PORT
68
PORT
66
PORT
64
PORT
62












PORT
59
PORT
57
PORT
55
PORT
53
PORT
51
PORT
49
PORT
71
PORT
69
PORT
67
PORT
65
PORT
63
PORT
61
30
29
28
27
26
25
36
35
34
33
32
31
BEAM
BEAM
BEAM
BEAM
BEAM
BEAM
BEAM
BEAM
BEAM
BEAM
BEAM
BEAM





1.32
PORT
78
PORT
76
PORT
74








PORT
96
PORT
94
PORT
92
PORT
90
PORT
88
PORT
86
PORT
84
PORT
82
PORT
80






PORT
81
PORT
79
PORT
77
PORT
75
PORT
73





39
38
37
PORT
95
PORT
93
PORT
91
PORT
89
PORT
87
PORT
85
PORT
83
BEAM
48
47
46
45
44
43
42
41
40
BEAM
BEAM
BEAM
BEAM
BEAM
BEAM
1.30
1.31
BEAM
BEAM
BEAM
BEAM
BEAM

BEAM PATTERN
Horizontal Beam Pattern (Row 1 & 3)
Horizontal Beam Pattern (Row 2 & 4)
Vertical Beam Pattern
5 / 8
2.30
2.20
2.00
2.10

TRANSPORTATION / INSTALLATION
Transportation (From Point to Point)
Bracket Mounting
6 / 8
Bolt & Nuts Sets
1
30cm to 120cm
Ø13mm x 8
4
M12 x 15cm=8sets
3.10
Strictly comply to the Local authority and regulatory on Workplace Safety and Health Control and
Measure when moving and transportation of large or heavy equipment, appropriate material
handling machine should be use.
(Risk Assessment apply for Forklift or Pallet Truck Lifting)
3.20
Item
Lens/Types
Holes Size
Bracket Qty
Page
3.00
ONE end bolt sets
Attached the bracket
tighten with
specified bolts sets.
Important Notes:
End User is require
to
Custom-Make
the additional
supporting bracket
and tighten to the
existing Antenna
bracket to meet the
deployment needs.

Installation using a crane
Lifting the Antenna
7 / 8
3.30
Page
Strictly comply to the local authority and regulatory on Workplace Safety and Health Control and
Measure when performing lifting of large or heavy equipment, appropriate material handling
machine should be used and only certified personnel should perform the task.
(Risk Assessment requirement applies for both Up-Lifting and Down-Lifting.)
3.31
The antenna has 2 hook points installed on the top frame (located slightly behind the center of the
sphere). These hooks are designed at the center of gravity point of the antenna. A cable, rope can be
securely fastened to the hooks and the antenna can be lifted using a crane as pictured below.

Antenna Installation
Antenna Leveling
Digital Level Gauge Calibration
Adjustment Requirement
8 / 8
Page
3.40
With reference to "Bracket Mounting Procedure", End user is required to Custom-Make the
additional supporting bracket and tighten it to the existing Antenna bracket to meet the deployment
needs.
3.41
After the Antenna is mounted to the bracket, it is required to be adjusted to 0˚ (Zero Degree) with
≤0.2˚ on 3 sides of the frame top level.(Rear, Right & Left=As shown in picture)
3.42
3.43