Matsing MS-MBA-3.3.2-C2-H2-L2-I User manual

TABLE OF CONTENTS:
BEAMS & CONNECTORS:
Plan View Resultant Beam Layout Connector Port Table
Connector Detail Connector Layout
PATTERN DIAGRAM
Frequency: 3700 - 4000 MHz Frequency: 1710 - 2690 MHz
Horizontal Pattern Horizontal Pattern
Vertical Pattern Vertical Pattern
Frequency: 698 - 960 MHz
Horizontal Pattern Vertical Pattern
MANUAL TILT ADJUSTMENT
BRACKET INSTALLATION
Bolts & Nuts Requirements
Tools Requirement
Bolts & Nuts Adjustable Spanner
Bracket M12 Spanner
Bracket Spacing & Installation Sample
Installation Complete (Remove Protective Foam)
GENERAL LIFTING GUIDE
Lifting Belts & Shackle (Item not included in shipping)
Lifting Belts
Shackle
Single Belt Sample
Dual Belts Sample
Example of Slanting installation
Revision History:
[email protected]
www.matsing.com 1 / 8
email:
website:
Page
Revision
nos.
5.20
5.30
5.40
Date
Description
Revised by
4.30
4.40
5.00
5.10
5.11
5.12
4.00
4.10
4.20
4.11
4.21
4.12
4.22
2.12
2.22
2.30
2.31
2.32
3.00
1.30
1.40
2.00
2.10
2.20
2.11
2.21
Pavel
MBA-332-F2H2L2-I-001
0
INSTRUCTION MANUAL MS-MBA-3.3.2-C2-H2-L2-I
1.00
1.10
1.20
MS-MBA-3.3.2-C2-H2-L2-I
Instruction Manual
Date
Prepared by
Approved by
Document nos
Rev
8 Nov 2022
Ray Ling

BEAMS & CONNECTORS:
Plan View Resultant Beam Layout Connector Port Table
Connector Layout
Connector Detail
2 / 8
BEAM 3
BEAM 2
BEAM 1
BEAM 3
BEAM 2
BEAM 1
(-45˚)
(-45˚)
(-45˚)
1.30
1.40
Page
(+45˚)
(+45˚)
(+45˚)
Port 12
Port 10
Port 8
Port 11
Port 9
Port 7
(-45˚)
(-45˚)
(-45˚)
BEAM 2
BEAM 1
Port 15 (+45˚)
Port 13 (+45˚)
Port 16 (-45˚)
Port 14 (-45˚)
(+45˚)
(+45˚)
(+45˚)
Port 6
Port 4
Port 2
Port 5
Port 3
Port 1
1.00
1.10
1.20
Port 1 (+45˚)
Port 2 (-45˚)
Port 7 (+45˚)
Port 8 (-45˚)
Port 5 (+45˚)
Port 6 (-45˚)
Port 3 (+45˚)
Port 4 (-45˚)
Port 11 (+45˚)
Port 12 (-45˚)
Port 9 (+45˚)
Port 10 (-45˚)
Port 13 (+45˚)
Port 14 (-45˚)
Port 15 (+45˚)
Port 16 (-45˚)
BEAM 2 BEAM 1 BEAM 3
BEAM 2
BEAM 1
BEAM 2
BEAM 1
BEAM 3
REAR VIEW CONNECTOR LAYOUT
MS-MBA-3.3.2-C2-H2-L2-I
AISG IN-1
CB Beam: 1
CB Ports: 1,2
HB Beam: 1
HB Ports: 7,8
LB Beam: 1
LB Ports: 13,14
AISG IN-2
CB Beam: 2
CB Ports: 3,4
HB Beam: 2
HB Ports: 9,10
AISG IN
CB Beam: 3
CB Ports: 5,6
HB Beam: 3
HB Ports: 11,12
LB Beam: 2
LB Ports: 15,16

PATTERN DIAGRAM
Frequency: 3700 - 4000 MHz
Horizontal Pattern
Vertical Pattern
3 / 8
2.00
2.10
2.11
2.12
Page
BEAM 2
3700 - 4000 MHz
Frequency:
MS-MBA-3.3.2-C2-H2-L2-I


Frequency:
3700 - 4000 MHz
MS-MBA-3.3.2-C2-H2-L2-I

Frequency: 1695 - 2690 MHz
Horizontal Pattern
Vertical Pattern
4 / 8
2.21
2.22
Page
2.20
BEAM 2
1710 - 2690 MHz
Frequency:
MS-MBA-3.3.2-C2-H2-L2-I


1710 - 2690 MHz
Frequency:
MS-MBA-3.3.2-C2-H2-L2-I

Frequency: 698 - 960 MHz
Horizontal Pattern
Vertical Pattern
5 / 8
Page
2.30
2.31
2.32
MS-MBA-3.3.2-C2-H2-L2-I 698 -960 MHz
Frequency:


698 -960 MHz
Frequency:
MS-MBA-3.3.2-C2-H2-L2-I

MANUAL TILT ADJUSTMENT
Bolts & Nuts
BRACKET INSTALLATION
Bolts & Nuts Requirements
Bracket
6 / 8
4.12
Page
Qty
Size
Qty
Size
Qty
2
M12 x
200mm
4
M12
10
3
When done, push the handle back in, screw the waterproof cap back to the
position.
4.11
4.00
4.10
Bracket
Bolts
Nuts
3.00
1
The MBA antenna come in RET mode as default, but if needed can also be
manually adjusted. To do so, please unscrew the waterproof cap behind the
element whose tilt is to be adjusted.
2
By Default the knob is on engaged mode, pull out the handle for manual tilt
adjustment, turn the handle to change the tilt.
Tilt
Adjustment
Knob
Angle
Indicator
RET
Controller
Removable
Radome
Protective
Foam

Tools Requirement
Adjustable Spanner M12 Spanner
Bracket Spacing & Installation Sample
Installation Complete
(Remove Protective Foam)
7 / 8
Page
4.40
4.20
4.21
4.22
4.30
1150
106
135
Remove
Protective
Foam

GENERAL LIFTING GUIDE
Lifting Belts & Shackle (Item not included in shipping)
Lifting Belts Shackle
Single Belt Sample Dual Belts Sample
Example of Slanting installation
8 / 8
5.40
Page
5.00
5.10
5.11
5.12
5.20
5.30
Antenna Installed,
Remove protective
Foam
Limitation in
Holding Structure
Distance
Step 1:
Lift antenna by lifting machine
Step 2:
Partial Secure Top Bracket
Step 3:
Push Antenna Bottom to
Secure Bottom Bracket
Step 4:
Final Secure all top and
bottom brackets