Matt Blatt AMAGER SIDEBOARD (OAK) User manual

AMAGER SIDEBOARD (OAK)
MBAMAGERSOA

COMPONENTS
No.
Dimensions (mm)
Qty
No.
Dimensions (mm)
Qty
1
1600 x 400 x 16
1
9
200 x 40 x 30
4
2
519 x 399 x 16
1
10
198 x 40 x 30
1
3
519 x 399 x 16
1
11
515 x 169 x 16
3
4
519 x 384 x 16
1
12
350 x 125 x 14
3
5
1600 x 400 x 59
1
13
350 x 125 x 14
3
6
1578 x 531 x 3
1
14
479 x 123 x 14
3
7
1026 x 320 x 16
1
15
489 x 344 x 3
3
8
514 x 526 x 16
2
16
1016 x 30 x 18
1
x3

Hardware
A
∅
6 x 44mm
(x30)
B
∅
15 x 12mm
(x18)
C
∅
12 x
∅
10mm
(x12)
D ∅
8 x 30mm
(x20)
E
M8 65mm
(x4)
F∅8/∅19mm
(x4)
G
M8
(x4)
H∅3.5 x 16mm
(x32)
J∅4 x 30mm (x12)
K∅4 x 40mm (x5)
L 350mm (x3)
M350mm (x3)
N5mm
(x1)
P∅6 x 8mm
(x18)
Q∅5mm
(x4)
R75 x 15 x 25mm
(x2)
S ∅4/∅12mm (x4)
T15 x 15mm (x20)
U∅20mm (x6)
V∅20mm (x12)
W ∅3.5 x 16mm (x4)

ASSEMBLY
Step 1: Insert D dowels into parts 2,3 and 4. Align M onto part 2 and L onto part 3.Using
a Phillips screwdriver (not supplied), secure M and L with P screws.
D(x12)
L(x2)
M(x2)
P(x12)

Step 2:
E(x4)
F(x4)
G(x4)
N(x1)
Step 3:
A(x9)

Step 4: Place parts 2,3 and 4 onto part 5. Ensuring the arrows on each Bpiece are
pointing to the corresponding Apiece, insert Bpieces into parts 2,3and 4then secure
Bto Awith a Phillips screwdriver (not supplied).
B(x9)
Step 5:

Step 6:
A(x9)
R(x2)
S(x4)
W(x4)
Step 7:
B(x9)

Step 8:
H(x20)
T(x20)
Step 9:
L(x1)
M(x1)
P(x6)
U(x6)

Step 10:
Q(x4)
Step 11:
D(x2)

Step 12:
K(x5)
Step 13:

Step 14:
Step 15: Insert A into one part labelled 11. Insert D into part 12 and 13.
Align parts 12 and 13 and connect with part 11.Repeat the whole process two more
times to create three drawer assemblies.
A(x12)
D(x6)
x3
Ⅰ
Ⅱ
Ⅰ
Ⅱ

Step 16: Insert part 15 onto one drawer assembly.
Ensuring the arrows on each Cpiece are pointing to the corresponding Apiece, insert
Cpieces into parts 12 and 13 then secure Cto Awith a Phillips screwdriver (not
supplied). Secure part 14 onto the drawer assembly with Jscrews.
Attach Vonto the drawer assembly. Repeat the whole process with the two remaining
drawer assemblies.
C(x12)
J(x12)
V(x12)
x3

Step 17:
Step 18: Using a spirit level (not supplied), check the unit is level. Adjust the height of
the legs using a flathead screwdriver (not supplied) if necessary.
Ⅰ
Ⅱ
Ⅲ
Ⅳ

Step 19: Place the unit against the wall where you would like the unit to be located.
Using a pencil, mark the location of the holes on the R brackets.Remove the unit and
use a drill (not supplied) to create holes at the marked locations.
Align the holes with the unit and R brackets,then use appropriate wall anchor plugs
and screws (not supplied) to secure the unit to the wall.
The maximum weight capacity of each drawer, the shelves, and top of the unit can
hold are 5kg, 10kg, and 20kg respectively.
TOPPLING FURNITURE WARNING:
•It is strongly recommended that this product is permanently fixed to the
wall.
•Please seek professional advice if you are in doubt of what fixing device to
use.
•Regularly check that anchors are securely maintained.
•Stability of tall items may be affected by thick carpets or uneven floors.
•Do not place unanchored televisions on furniture.
Caution! For your safety when attaching the anchor fixings, please note the
following: Check any electrical wires or plumbing inside the wall before drilling any
holes (if you are unsure, please seek professional advice from a qualified
tradesperson).
Ⅰ
Ⅱ
Ⅲ
Ⅳ
Ⅴ
Ⅵ

NEED MORE INFORMATION?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.mattblatt.com.au