MaxLite MaxLite HL Series User manual

Operating Instructions HL Series
MaxLite LED Linear HighBay Fixtures
• To reduce the risk of death, personal injury or property damage from fire,
electric shock, falling parts, cuts/abrasions, and other hazards read all
warnings and instructions included with and on the fixture box and all
fixture labels.
• Before installing, servicing, or performing routine maintenance upon
this equipment, follow these general precautions.
• Commercial installation, service and maintenance of luminaires should be
performed by a qualified licensed electrician.
• DO NOT NSTALL DAMAGED PRODUCT!
ARNING:
R SK OF ELECTR CALSHOCK
• Turn off electrical power at fuse or circuit breaker box before wiring fixture
to the power supply.
• Turn off the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire label
information.
• Make all electrical and grounded connections in accordance with the National Electrical
Code and any applicable local code requirements.
• All wiring connections should be capped with UL approved wire connectors.
CAUTION:
R SK OF NJURY
• Wear gloves and safety glasses at all times when removing luminaire from carton, installing,
servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.
• Account for small parts and destroy packing material, as these may be hazardous to children.
CAUTION:
R SK OF F RE
• Keep combustible and other materials that can burn away from luminaire and lamp/lens.
• M N 90°C SUPPLY CONDUCTORS.
© Copyright 2018. MaxLite, nc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: [e-mail]
Page: 1
REV: 08/13/18
®
General Safety Information

Connect the green (ground), black (line) and
white (neutral) wires of the AC line to the
similarly colored wires of the fixture’s power
supply using UL listed connectors. Place all
connections and exposed wire inside of fixture
and reattach power access plate.
Operating Instructions HL Series
MaxLite LED Linear HighBay Fixtures
®
iring Instructions
EM iring Instructions
© Copyright 2018. MaxLite, nc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: [e-mail]
Page: 2
REV: 08/13/18

Mounting Instructions
CAUTION: Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
Aircraft Cable Mount:
Operating Instructions HL Series
MaxLite LED Linear HighBay Fixtures
®
Locate a structural member and inspect it for
damage. Secure the aircraft cable around the
member and run it through the gripper to fas-
ten it. The cable enters and exits through the
side of the gripper. Adjust the fixture height
by drawing the cable through the gripper,
refer to Fig. 1.
Secure the bottom aircraft cable onto the LED high bay
by inserting the toggles through the 0.375” hole, refer to
Fig. 2.
Chain Mount:
Run the chain link through both
V-hooks and attach the hooks onto the
fixture, as shown in Fig. 1.
Locate a secure structural member and inspect it
for damage. Secure the chains around the member
and lock it with the S-hook, as shown in Fig. 2.
© Copyright 2018. MaxLite, nc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: [e-mail]
Page: 3
REV: 08/13/18

Mounting Instructions
CAUTION: Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
Operating Instructions HL Series
MaxLite LED Linear HighBay Fixtures
®
Locate the secure threaded stem/pole and
inspect for damage. Using the cord grip
provided, securely attach the input wires
onto the cover plate, as shown in Fig. 1.
Mono-Stem Mount:
© Copyright 2018. MaxLite, nc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: [e-mail]
Page: 4
REV: 08/13/18
Attach the base bracket onto the fixture by inserting four (4)
M4 screws, as shown in Fig. 2.
Secure the top mounting bracket onto the
stem/pole by placing one (1) nut before
installing the bracket and one (1) nut after,
as shown in Fig. 3.
Slide the assembled fixture onto the top mounting bracket
attached to the stem/pole. Secure the fixture to the bracket
using the two (2) screws shown in Fig. 4. Wire the input
wires to the fixture.
Attach the cover plate by tightening three
(3) M4 screws as shown in Fig. 5.

Mounting Instructions
CAUTION: Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
Stem/Pendant Mount:
Operating Instructions HL Series
MaxLite LED Linear HighBay Fixtures
®
Locate a secure structural member and inspect it for
damage. Knockout two (2) 3/8” KO.
© Copyright 2018. MaxLite, nc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: [e-mail]
Page: 5
REV: 08/13/18
Knockouts
Feed the stems into the two (2) knockout holes
and secure them with nuts.
Surface Mount:
Locate a secure structural
member and inspect it for
damage. Secure the top mounting
bracket onto the flat surface using
four (4) #8 screws. Use the drill
pattern figure shown in Fig. 1.
Using the cord grip provided, securely
attach the input wires onto the cover
plate, as shown in Fig. 2. The cord grip
can also be attached to the either side
of the top mounting bracket using the
knockout holes for daisy-chain
applications.
Attach the base bracket onto the
fixture by inserting four (4) M4
screws, as shown in Fig. 3.
Slide the assembled fixture onto the surface
mounted top mounting bracket. Secure the
fixture to the bracket using the two (2) screws
shown in Fig. 4. Wire the input wires to the
fixture.
Attach the cover plate by tightening three (3) M4 screws
as shown in Fig. 5.

Operating Instructions HL Series
MaxLite LED Linear HighBay Fixtures
®
© Copyright 2018. MaxLite, nc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: [e-mail]
Page: 6
REV: 08/13/18
Driver Access Instructions
Remove the two (2) bottom center screws
securing the center driver plate to the fixture.
Slide the driver plate to the left or right
depending on the orientation of the fixture,
see Fig. 1.
The center plate will hinge from one side, as
shown in Fig. 2. allowing access to the driver.
Once repairs are done, slide the plate back
into place and replace the two (2) screws.
Lens Removal Instructions
Remove the two (2) bottom screws closer to the
center of the fixture. Slide the lens to the right
towards the center of the fixture, freeing the left
side of the lens, as shown in Fig. 1.
Remove the lens to have access to the LED
board, as shown in Fig. 2. Once repairs are
complete, slide the lens back into place and
replace the two (2) screws.
LED Board
ire Guard Instructions
Using the four (4) included M4 machine screws and
four (4) included bracket clips (refer to Fig. 1), snap
the clips onto the wire guard, and secure the clips
to the fixture with the screws (Fig. 2).

Operating Instructions HL Series
MaxLite LED Linear HighBay Fixtures
®
MaxLite nc. warrants its products for a minimum period of FIVE (5) years from the date of original purchase from
MaxLite or its authorized distributor/dealer (the “Warranty Period”), as follows: f a Product fails to operate during the
Warranty Period as a result of defects in materials or workmanship, MaxLite will, at its option, repair it, replace it with
the same or like Product.
Please refer to Maxlite’s website (at http://maxlite.com/resources/warranties) for the complete
terms and conditions of our warranty.
Limitation of Liability
THE FOREGO NG WARRANTY S EXCLUS VE, AND S THE SOLE REMEDY FOR ANY AND ALL CLA MS,
WHETHER N CONTRACT, N TORT OR OTHERW SE AR S NG FROM THE FA LURE OF PRODUCT AND S N
L EU OF ALL OTHER WARRANT ES, EXPRESS OR MPL ED, NCLUD NG ALL WARRANT ES OF
MERCHANTAB L TY OR F TNESS FOR A PART CULAR PURPOSE, WH CH WARRANT ES ARE HEREBY
EXPRESSLY D SCLA MED TO THE EXTENT PERM TTED BY LAW AND, N ANY EVENT, SHALL BE L M TED TO
THE WARRANTY PER OD SPEC F ED ABOVE. THE L AB L TY OF MAXL TE SHALL BE L M TED TO THE TERMS
OF THE EXPRESS WARRANTY SET FORTH HERE N. N NO EVENT W LL MAXL TE BE L ABLE FOR ANY
SPEC AL, NC DENTAL OR CONSEQUENT AL DAMAGES NCLUD NG, W THOUT L M TAT ON, DAMAGES
RESULT NG FROM LOSS OF USE, PROF TS, BUS NESS OR GOODW LL, LABOR COSTS, REMOVAL OR
NSTALLAT ON COSTS, DECREASE N THE L GHT OUTPUT OF THE LAMP, AND/OR DETER ORAT ON N THE
LAMP’S PERFORMANCE, WHETHER OR NOT MAXL TE HAS BEEN ADV SED OF THE POSS B L TY THEREOF.
UNDER NO C RCUMSTANCES SHALL MAXL TE’S ENT RE L AB L TY FOR A DEFECT VE PRODUCT EXCEED
THE PURCHASE PR CE OF THAT PRODUCT. WARRANTY SERV CES PROV DED UNDER THESE TERMS AND
COND T ONS DO NOT ENSURE THE UN NTERRUPTED OPERAT ON OF PRODUCTS; MAXL TE SHALL NOT BE
L ABLE FOR DAMAGES CAUSED BY ANY DELAYS NVOLV NG WARRANTY SERV CE.
This Limited Warranty gives you specific legal rights and you may also have other rights that may vary from state to
state. Because some states or jurisdictions do not allow the exclusion or limitation of liability for consequential or
incidental damages, this limitation may not apply to you.
arranty Information
© Copyright 2018. MaxLite, nc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: [e-mail]
Page: 7
REV: 08/13/18