MaxLite LSU Series User manual

Operating Instructions L U eries
MaxLite LED Utility Wrap Fixture
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [e-mail]
Page: 1
R V: 05/03/18
®
General afety Information
• To reduce the risk of death, personal injury or property damage from fire,
electric shock, falling parts, cuts/abrasions, and other hazards read all
warnings and instructions included with and on the fixture box and all
fixture labels.
• Before installing, servicing, or performing routine maintenance upon
this equipment, follow these general precautions.
• Commercial installation, service and maintenance of luminaires
should be performed by a qualified licensed electrician.
• For Residential installation: If you are unsure about the installation or
maintenance of the luminaires, consult a qualified licensed electrician
and check your local electrical code.
• DO NOT INSTALL DAMAG D PRODUCT!
• This fixture is intended to be connected to a properly installed and grounded
UL listed junction box.
WARNING:
RISK OF L CTRICALSHOCK
• Turn off electrical power at fuse or circuit breaker box before wiring fixture
to the power supply.
• Turn off the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire label
information.
• Make all electrical and grounded connections in accordance with the National lectrical
Code and any applicable local code requirements.
• All wiring connections should be capped with UL approved wire connectors.
CAUTION:
RISK OF INJURY
• Wear gloves and safety glasses at all times when removing luminaire from carton, installing,
servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.
• Account for small parts and destroy packing material, as these may be hazardous to children.
CAUTION:
RISK OF FIR
• Keep combustible and other materials that can burn away from luminaire and lamp/lens.
• MIN 90°C SUPPLY CONDUCTORS.
Models: LSU Series
Picture is for illustration purposes
only. Your model may vary.

General Wiring Diagram
CAUTION: Turn off electrical power at fuse
or circuit breaker box before wiring fixture to
the power supply.
Connecting panels to AC source supply:
All units must be individually connected to
the AC supply. (120-277 VAC)
Black = Line
White = Neutral
Green = Ground
Operating characteristic:
Voltage input: 120-277V 50/60 Hz
Operating temp: -4°F to 104°F
**Consult with dimmer control
manufacturer’s wiring instructions
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [e-mail]
Page: 2
R V: 05/03/18
Operating Instructions L U eries
MaxLite LED Utility Wrap Fixture
®
Mounting Instructions
Before installation, ensure if power supply is disconnected. Cables must be connected in accordance
to instruction and proper standing rules.
1. Remove lens and wire way cover. Slide lens toward one end while lifting opposite end clear of fixture
housing. If not clearing easily, ensure lens has slide past retainer clip inside the end cap.
2. Next squeeze both sides of wire cover until they clear metal tabs and remove cover.
3. Select wiring access point and remove appropriate knockout.
4. Select installation point and locate studs.

Mounting Instructions
Before installation, ensure if power supply is disconnected. Cables must be connected in accordance
to instruction and proper standing rules.
5. For rear access points feed wires through hole.
6. Using 1” mounting screw or 3”x3/16 toggle bolts, secure fixture in place using keyhole slots provided.
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [e-mail]
Page: 3
R V: 05/03/18
Operating Instructions L U eries
MaxLite LED Utility Wrap Fixture
®
Lens
Cover
Driver
N
L
crew
7. After making wiring connections, replace wire cover and diffuser into place.
8. Secure lens to housing by inserting clips at both ends of the fixture, as shown in the image below.
9. Restore power to branch circuit and energize the luminaire.
Metal Clips

Optional Motion ensor
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [e-mail]
Page: 4
R V: 05/03/18
Operating Instructions L U eries
MaxLite LED Utility Wrap Fixture
®
Lens
Access crews
Upper Housing
Lower Housing
Coupling Assembly
tand offs
Mounting Key Holes
Motion ensor Option Wiring

etting & Adjusting Motion ensor
Operating Instructions L U eries
MaxLite LED Utility Wrap Fixture
®
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [e-mail]
Page: 5
R V: 05/03/18
To make setting and control adjustments, you will need to access the three rotary DIP controls behind the lens.
Control Mode
The LOD-500 series features 8 different control modes
for selection via rotary DIP switch. Please refer to the
following table and sensor operation charts to select the
desired control mode.
W. ABCDE F G H
0SMA0SLA0S0T STMOD 0SHA 0SLAT0 0SMAT0 0SHAT0
AB
C
D
E
F
G
H
MODE
(T ST)
1
234
5
60
1
234
5
60
MODE
TIME DIM
TIME
(10 minutes)
DIM
(OFF)(Factory set)
PO .
TIME
DIM
0123456
1’ 3’ 5’ 10’ 15’ 20’ 30’
OFF 5% 10% 20% 25% 33% 50%
Delay Time
The LOD-500 series offers 7 different delay
time settings via Accu-Set potentiometer.
The light will remain ON if sensor detects
occupant’s movement before the set delay
time expires. The Accu-Set potentiometer will
provide accurate delay time as the arrowhead
pointed.
Dim Level
The LOD-500 series offers 7 different dim
level settings via Accu-Set potentiometer.
The L D light will be dimmed as the level set
when condition of selected control mode
applies. The Accu-Set potentiometer will
provide accurate dim level as the arrowhead
pointed.
ensor Operation
Default
Parking
Profile
Default
tair
Profile
Battery Backup Option
Your MaxLite Utility wrap fixture may come equipped with a battery back up power system.
Please review all following remarks to prevent any damage or risk while installing or using your fixture:
This Option is covered under UL 1598 and is a factory assembled system. Any field installation will void the factory
warranty unless express written authorization is given in advance.
Contains Nickel-Cadmium Rechargeable Battery. Must be recycled or disposed properly.
Output LVL Compliant
Please note, your control is equipped with a quality
neoprene seal. This seal does expand over time
providing maximum sealing protection possible. If you
have any trouble re-installing the lens, a light coating
of WD-40 as lubricant, to the seal, will make installing
the lens easier. Care should be taken NOT to spray
lubricant into the DIP switches.

Operating Instructions L U eries
MaxLite LED Utility Wrap Fixture
®
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [e-mail]
Page: 6
R V: 05/03/18
Battery Backup Option (Continued)
R AD AND FOLLOW ALL SAF TY INSTRUCTIONS!
1. To prevent high voltage from being present on yellow & orange output leads prior to installation,
converter connector must be open. Do not join converter connector until installation is complete and AC
power is supplied to the emergency driver.
2. This product is for use with an emergency L D lighting load and supplies up to 8.4 W of power(measured
at nominal battery voltage) at a maximum voltage of 60VDC and in emergency mode for a minimum of 90
minutes.
3. Make sure all connections are in accordance with the National lectrical Code or Canadian lectrical Code
and any local regulations.
4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and convert
connector of the emergency driver before servicing.
5. This emergency driver is for factory installation only.
6. This product is suitable for use in damp locations where the ambient temperature is 0ºC minimum, +50ºC
maximum. Product is not suitable for heated air outlets and wet or hazardous locations.
7. An unswitched AC power source is required (120 - 277 VAC, 60 Hz)
8. Do not install near gas or electric heaters.
9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not field
replaceable. Contact the manufacturer for information on service.
10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
11. Do not use this product for other than intended use.
12. Servicing should be performed by qualified service personnel.
13. Only apply to L D Driver which the output current less than 3.0A.
14. quipment should be mounted in locations and at heights where it will not be subjected to tampering by
unauthorized personnel. SAV TH S INSTRUCTIONS.

Operating Instructions L U eries
MaxLite LED Utility Wrap Fixture
®
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [e-mail]
Page: 7
R V: 05/03/18
Your fixture comes with an
additional housing on rear to
enclose the battery back up
unit
Fixture
Housing
BBU
ide View
tep Down Transformer (347V Only)
CAUTION: Always disconnect power to luminaire before
attaching, removing or servicing. Risk of shock or fire.
1. Location of SDT.
Driver
SDT
Note: not suitable for BBU models.

MaxLite Inc. warrants its products for a minimum period of FIVE (5) years from the date of original purchase from
MaxLite or its authorized distributor/dealer (the “Warranty Period”), as follows: If a Product fails to operate during the
Warranty Period as a result of defects in materials or workmanship, MaxLite will, at its option, repair it, replace it with
the same or like Product.
Please refer to Maxlite’s website (at http://maxlite.com/resources/warranties) for the complete
terms and conditions of our warranty.
Limitation of Liability
TH FOR GOING WARRANTY IS XCLUSIV , AND IS TH SOL R M DY FOR ANY AND ALL CLAIMS,
WH TH R IN CONTRACT, IN TORT OR OTH RWIS ARISING FROM TH FAILUR OF PRODUCT AND IS IN
LI U OF ALL OTH R WARRANTI S, XPR SS OR IMPLI D, INCLUDING ALL WARRANTI S OF
M RCHANTABILITY OR FITN SS FOR A PARTICULAR PURPOS , WHICH WARRANTI S AR H R BY
XPR SSLY DISCLAIM D TO TH XT NT P RMITT D BY LAW AND, IN ANY V NT, SHALL B LIMIT D TO
TH WARRANTY P RIOD SP CIFI D ABOV . TH LIABILITY OF MAXLIT SHALL B LIMIT D TO TH T RMS
OF TH XPR SS WARRANTY S T FORTH H R IN. IN NO V NT WILL MAXLIT B LIABL FOR ANY
SP CIAL, INCID NTAL OR CONS QU NTIAL DAMAG S INCLUDING, WITHOUT LIMITATION, DAMAG S
R SULTING FROM LOSS OF US , PROFITS, BUSIN SS OR GOODWILL, LABOR COSTS, R MOVAL OR
INSTALLATION COSTS, D CR AS IN TH LIGHT OUTPUT OF TH LAMP, AND/OR D T RIORATION IN TH
LAMP’S P RFORMANC , WH TH R OR NOT MAXLIT HAS B N ADVIS D OF TH POSSIBILITY TH R OF.
UND R NO CIRCUMSTANC S SHALL MAXLIT ’S NTIR LIABILITY FOR A D F CTIV PRODUCT XC D
TH PURCHAS PRIC OF THAT PRODUCT. WARRANTY S RVIC S PROVID D UND R TH S T RMS AND
CONDITIONS DO NOT NSUR TH UNINT RRUPT D OP RATION OF PRODUCTS; MAXLIT SHALL NOT B
LIABL FOR DAMAG S CAUS D BY ANY D LAYS INVOLVING WARRANTY S RVIC .
This Limited Warranty gives you specific legal rights and you may also have other rights that may vary from state to
state. Because some states or jurisdictions do not allow the exclusion or limitation of liability for consequential or
incidental damages, this limitation may not apply to you.
Warranty Information
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [e-mail]
Page: 8
R V: 05/03/18
Operating Instructions L U eries
MaxLite LED Utility Wrap Fixture
®