MaxLite maxLED MLCAN20LED50 User manual

© Copyright 2013. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: inf[email protected]
Page: 1
12/9/2013
Installation Manual
20W LED Ceiling Canopy
The surface mounted canopy fixture, with a shatter and UV resistant polycarbonate
lens, can be mounted to J-box or directly to non-combustable surfaces.
The LEDs are proprietary binned for color consistency, highlighting a 9 percent power
factor and 120° beam angle LED.
De cription
Fixtu e: Available in a bronze finish, the
heavy-duty die cast aluminum one-
piece housing is polyester powder-
coated for long durability, rust and
corrosion proof, and sealed to be dirt
and insect proof.
Lens: High quality shock proof
polycarbonate lens with UV inhibitors.
LED Module: LED modules are copper
plated to provide high thermal transfer
rate and minimize the junction
temperature of LEDs to maximize
service life.
Con truction
Model Watts Lumens Volts Weight Dimensions (in)
L W D
MLCAN20LED50 20 1,312 120-277V 6.5 lb 8-15/16” 8-15/16” 7-1/4”
Specifications

© Copyright 2013. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: inf[email protected]
Page: 2
12/9/2013
20W LED Ceiling Canopy
Installation Manual
In tallation & Operation:
Warranty
Drill four mounting holes into mounting surface using a 1/4” drill bit. Use template to locate mounting1
holes.
Use a Phillips Head screwdriver to loosen (4) screws securing fixture light engine/lens assembly.2
Remove fixture base plate from fixture.
Use a flat head screwdriver to remove appropriate wire way covering from housing. This is to be3
determined by the installer.
Take care to avoid damaging driver, wires and quick connectors and drill holes through casting over4
fixture mounting holes.
Affix fixture to mounting surface by installing anchors (not supplied) through fixture mounting holes5
into holes drilled into the mounting surface. Be sure to use an anchor appropriate for the mounting
surface in which the fixture is installed.
Add 1/4” bead of exterior grade silicone sealant around the6
outside perimeter in the seam between the mounting
surface and the fixture base to inhibit any moisture from
attachment screws.
Reattach fixture light engine/lens assembly to fixture base7
housing.
Connect driver OUTPUT leads to quick connect originating
from LED array. Red output to quick connect with red wires,
black output to quick connect with black wires.
Reattach fixture using Phillips Head screws removed in9
mounting step 2.
LIMITED FIVE-YEAR WARRANTY
Should this product fail to perform satisfactorily due to a defect or poor workmanship with FIVE YEAR
from the date of purchase, return it to the place of purchase and it will be replaced, free of charge.
Incidental or consequential damages are excluded from this warranty.
!WARNING
Disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at the fuse
box. Turning the power off using the light switch is not sufficient to prevent electrical shock.
6-1/2”
3-1/4”
82.5
165

© Copyright 2013. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: inf[email protected]
Page: 3
12/5/2013
20W LED Ceiling Canopy
Installation Manual
General Safety Information
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.1
Review the diagram thoroughly before beginning. If you feel you do not have electrical wiring2
experience, have your fixture installed by a qualified licensed electrician.
All electrical connections must be in accordance with local codes, ordinance, and the National3
Electric Code. If you are unfamiliar with methods of installing electrical wiring, secure the services of a
qualified licensed electrician.
Before starting the installation, disconnect the power by turning off the circuit breaker or by removing4
the appropriate fuse at the fuse box. Turning the powe off using the light switch is not sufficient to
prevent electrical shock.
Equipment should be mounted in location and at heights where it will not readily be subject to5
tampering by unauthorized personnel.
Do not use this equipment for other than intended use.6
All servicing should be performed by qualified personnel only.7
AC Wiring In truction
Feed wires through way and secure using connector (not supplied) if needed.1
Connect supply wires to quick connect originating from INPUT side of driver. 2
Black/Hot supply to quick connect with black wire. White/Neutral supply to quick connect with white
wire. Be sure to confirm connections are secure.
Connect ground wire to quick connect with green wire. Be sure to confirm grounding connection is3
secure.
!CAUTION
Wiring Diagrams
LED Driver
Black
Green
White
Black
Red
Quick Connector
Ground Neutral Line
To Fixture
Housing

© Copyright 2013. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] Email: inf[email protected]
Page: 4
12/9/2013
20W LED Ceiling Canopy
Installation Manual
2