MaxLite WPCS Series User manual

Operating Instructions
MaxLite LED Wall Packs (Cutoff & Standard)
• To reduce the risk of death, personal injury or property damage from
fire, electric shock, falling parts, cuts/abrasions, and other hazards
read all warnings and instructions included with and on the fixture
box and all fixture labels.
• Before installing, servicing, or performing routine maintenance upon
this equipment, follow these general precautions.
• Commercial installation, service and maintenance of luminaires
should be performed by a qualified licensed electrician.
• For Residential installation: If you are unsure about the installation or
maintenance of the luminaires, consult a qualified licensed electrician
and check your local electrical code.
• DO NOT INSTALL DAMAG D PRODUCT!
• This fixture is intended to be connected to a properly installed and
grounded UL listed junction box.
WARNING:
RIS OF ELECTRICAL SHOC
• Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
• Turn off the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• Make all electrical and grounded connections in accordance with the National Electrical Code
and any applicable local code requirements.
• All wiring connections should be capped with UL approved wire connectors.
CAUTION:
RIS OF INJURY
• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing
or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.
• Account for small parts and destroy packing material, as these may be hazardous to children.
CAUTION:
RIS OF FIRE
• eep combustable and other materials that can burn away from luminaire and lamp/lens
• MIN 90°C SUPPLY CONDUCTORS.
WPS20AU50XXXXX 120-277V 50/60 Hz WPL80AU50 120-277V 50/60 Hz
WPS30AU50XXXXX 120-277V 50/60 Hz WPS20A350XXXXX 347V 50/60 Hz
WPCS20AU50XXXXX 120-277V 50/60 Hz WPS30A350XXXXX 347V 50/60 Hz
WPCS30AU50XXXXX 120-277V 50/60 Hz WPCS20A350XXXXX 347V 50/60 Hz
WPCL40AU50XXXXX 120-277V 50/60 Hz WPCS30A350XXXXX 347V 50/60 Hz
WPCL55AU50XXXXX 120-277V 50/60 Hz WPL55AH50XXXXX 347-480V 50/60 Hz
WPS20AU50XXXXX 120-277V 50/60 Hz WPL40AH50XXXXX 347-480V 50/60 Hz
WPS30AU50XXXXX 120-277V 50/60 Hz WPCL40AH50XXXXX 347-480V 50/60 Hz
WPL40AU50XXXXX 120-277V 50/60 Hz WPCL55AH50XXXXX 347-480V 50/60 Hz
WPL55AU50XXXXX 120-277V 50/60 Hz WPS28BU50XXXX 120-277V, 50/60 HZ
WPS40BU50XXXX 120-277V, 50/60 HZ WPS50BU50XXXX 120-277V, 50/60 HZ
WPS28BH50XXXX 347-480V, 50/60 HZ WPS40BH50XXXX 347-480V, 50/60 HZ
WPS50BH50XXXX 347-480V, 50/60 HZ
Model options:
If XXXX = PC12, voltage input 120V, 50/60Hz
If XXXX = PC27, voltage input 208-277V, 50/60 Hz
If XXXX = PC, voltage input 120-277V, 50/60Hz
If XXXX = MS, voltage input 120-277V, 50/60 Hz
If XXXX = IBB, voltage input 120-277V, 50/60 Hz
© Copyright 2017. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [email protected]
Page: 1
R V: 5/22/17
®
Picture is for illustration purposes
only. Your model may vary.
General Safety Information

General Wiring Diagram
CAUTION: Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
Connecting panels to AC source supply:
All units must be individually connected to the AC supply. (see page 1 for voltage by model)
Black = Line
White = Neutral
Green = Ground
AC Wiring Instructions
1. Feed wires through wire way and secure using connector (not supplied).
2. Connect supply wires to quick connect originating from INPUT side of driver. Black/Hot supply to
quick connect with black wire. White/Neutral supply to quick connect with white wire. Be sure to
confirm connections are secure.
3. Connect ground wire to quick connect with green wire. Be sure to confirm grounding connection
is secure.
Operating Instructions
MaxLite LED Wall Packs (Cutoff & Standard)
®
© Copyright 2017. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [email protected]
Page: 2
R V: 5/22/17
347-480V with Step Down Transformer

WPL80 Wiring Instructions
© Copyright 2017. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [email protected]
Page: 3
R V: 5/22/17
Operating Instructions
MaxLite LED Wall Packs (Cutoff & Standard)
®

Installation & Operation
Disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at the fuse box.
Turning the power off using the light switch is not sufficient to prevent electrical shock.
1. Drill three mounting holes into mounting surface using a 3/8” drill bit. Use template to locate mounting holes.
2. Use a screwdriver to loosen (2) screws securing fixture door. Remove fixture rear housing from fixture.
3. Use a flat head screw driver to remove appropriate wire way covering from back plate of housing.
4. Take care to avoid damaging driver, wires and quick connectors and drill holes through castings over fixture
mounting holes.
5. Affix fixture to mounting surface by installing anchors (not supplied) through fixture mounting holes into holes
drilled into the mounting surface. Be sure to use an anchor appropriate for the mounting surface in which the
fixture is installed.
6. Add ¼” bead of exterior grade silicone sealant around the perimeter
of the wall pack on the wall to inhibit any moisture from attachment
screws. Remove the pull-through plugs from the two weep holes at
the bottom of the fixture front housing to reduce condensation
buildup and avoid water buildup within the fixture. (see photo on right)
7. Reattach fixture front to fixture rear housing.
8. Connect driver OUTPUT leads to quick connect originating from
L D array. Red output to quick connect with red wires, black output
to quick connect with black wires.
9. Reattach fixture using two screws removed in installation step 2.
Operating Instructions
MaxLite LED Wall Packs (Cutoff & Standard)
®
Daylight/Motion Sensor Option: Wiring Diagram
Be sure that the unused second yellow wire is capped.
© Copyright 2017. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [email protected]
Page: 4
R V: 5/22/17

Operating Instructions
MaxLite LED Wall Packs (Cutoff & Standard)
®
Daylight/Motion Sensor Option: Function Definitions
2 MOTION TIME DELAY
The length of time the motion sensor will keep the lights on and at maximum level after it last
detects motion.
4 TEST & BLIN -BAC MODE
AUTO SET-POINT
Photocell calibration procedure for detecting optimum lighting control level.
BLIN -BAC MODE
The type of visual feedback that is provided when programming via the push-button; i.e. entire fixture
will blink or just sensor L D will blink.
TEST MODE
Disables Minimum On Time, sets Occupancy Time Delay to 30 sec, and shortens all photocell
transition and dimming rates. Mode will expire after 10 min or if function 4 is changed.
5 TEN’S DIGIT OF SET-POINT
The ten’s digit of the target light level that is to be maintained by the device (in foot-candles).
6 ONE’S DIGIT OF SET-POINT
The one’s digit of the target light level that is to be maintained by the device (in foot-candles).
7 SUNLIGHT DISCOUNT FACTOR
Value used to improve the tracking accuracy of a photocell during periods of high daylight. Decreasing
the value will lower the controlled levels of the lights.
8 INCREMENTAL SET-POINT ADJUSTMENT
Alters the target light level that is to be maintained by the device (in foot-candles).
9 RESTORE FACTORY DEFAULTS
Returns the sensor to its default settings.
11 PHOTOCELL CONTROL
Indicates what mode of photocell operation, if any, is enabled.
12 RAMP UP RATE
Time period from when motion is detected to when lights are at high trim level.
13 FADE DOWN RATE
Time period from when motion time delay expires to when lights are at low trim level.
15 MAXIMUM LEVEL (HIGH TRIM)
The output level (0-10 VDC) of the sensor after motion is detected.
16 MINIMUM LEVEL (LOW TRIM)
The output level (0-10 VDC) of the sensor after the fade down time has elapsed.
21 PHOTOCELL TRANSITION OFF TIME
The time period after the photocell measures a light level above the set-point (plus the deadband)
that it will turn the lights off (or dim them to min level).
22 PHOTOCELL TRANSITION ON TIME
The time period after the photocell measures a light level below the set-point that it will turn lights on.
© Copyright 2017. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [email protected]
Page: 5
R V: 5/22/17

Operating Instructions
MaxLite LED Wall Packs (Cutoff & Standard)
®
Please read all 3 steps before programming
1. nter a programming function by pressing button the number of times as the desired function number
from the tables below. (e.g. press twice for function 2, motion time delay).
2. L D will flash back the selected function’s current setting (e.g. 3 flashes for 5 minute time delay). To
change setting, proceed to step 3 before flash back sequence repeats 3 times. To exit the current function
or to change to a different function, wait for the sequence to repeat 3 times then return to step 1.
3. Press button the number of times indicated in the particular function’s detailed table for the N W desired
setting (e.g. press 5 times for 10 min). As confirmation of setting change, L D flashes back the N W
setting 3 times before exiting.
Daylight/Motion Sensor Option: Programming Instructions
Programming Functions
2Motion Time Delay
4Test & Blink-Back Mode
5Ten’s Digit of Set-Point
6One’s Digit of Set-Point
7Sunlight Discount Factor
8Incremental Set-Point Adjustment
9Restore Factory Defaults
11 Photocell Operation
12 Ramp Up Rate
13 Fade Down Rate
15 Maximum Level (High Trim)
16 Minimum Level (Low Trim)
21 Photocell Transition Off Time
22 Photocell Transition On Time
Detailed Function Tables (* Default Setting)
2 = Motion Time Delay
130 sec 47.5 min 715.0 min
22.5 min 510.0 min 817.5 min
35.0 min* 612.5 min 920.0 min
4 = Test & Blink-Back Mode
1Blink Light & L D* 5Blink Set-Point ¹
2 Blink L D only 6Test Mode ²
4Auto-Setpoint
¹ The L D will blink back the ten’s digit, then pause,
then blink back the one’s digit. For a “0” the L D will
blink very rapidly. The sequence is repeated 3 times.
² Test Mode will set Occupancy Time Delay to 30
sec, and shorten all photocell transitions and
dimming rates. Mode will expire after 10 min or if
function 4 is set back to previous setting.
5 = Ten’s Digit of Set-Point
110 fc 440 fc 7200 fc
220 fc 550 fc 10 0 fc*
330 fc 6100 fc
6 = One’s Digit of Set-Point
11 fc 44 fc 77 fc 10 0 fc
2 2 fc 55 fc* 88 fc
33 fc 66 fc 99 fc
7 = Sunlight Discount Factor
1x/1* 4x/4 7x/7 10 x/10
2 x/2 5x/5 8x/8
3x/3 6x/6 9x/9
8 = Incremental Set-Point Adjustment
1 Decrease 1 fc 2Increase 1 fc
9 = Restore Factory Defaults
1 Keep Current* 2Restore Factory Defaults
11 = Photocell Operation
1 High/Off* 2High/Low 3Disabled
12 = Ramp Up Rate
1Instant 43 sec* 715 sec 10 1 min
2 1 sec 55 sec 820 sec
32 sec 610 sec 930 sec
13 = Fade Down Rate
1Instant 45 min* 715 min 10 1 hr
2 30 sec 57.5 min 820 min
32.5 min 610 min 930 min
15 = Maximum Level (High Trim)
1Off 43 Volt 7 6 Volt 10 9 Volt
2 1 Volt 54 Volt 8 7 Volt 11 10 Volts*
32 Volt 65 Volt 98 Volt
16 = Minimum Level (Low Trim)³
1Off 43 Volt 7 6 Volt 10 9 Volt
2 1 Volt 54 Volt 8 7 Volt 11 10 Volts*
32 Volt 65 Volt 98 Volt
³ Default Setting is determined by last digits in unit
model number. eg. 3V = 3 Volts.
21 = Photocell Transition Off Time
145 sec 35 min* 5 15 min 10 25 min
2 2 min 410 min 6 20 min
22 = Photocell Transition On Time
145 sec* 35 min* 5 15 min 10 25 min
2 2 min 410 min 6 20 min
© Copyright 2017. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [email protected]
Page: 6
R V: 5/22/17

Operating Instructions
MaxLite LED Wall Packs (Cutoff & Standard)
®
© Copyright 2017. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [email protected]
Page: 7
R V: 5/22/17
The MSWSFSP221B mounts to a fixture/enclosure with a 1/2” knock
out, via a nipple on the back. MSWSFSP221B operates at 100-347V
Single Phase, as well as 208/230/480VAC phase-to-phase. No power
pack is required. It is designed to be installed in indoor and outdoor
environments. The sensor uses passive infrared (PIR) sensing
technology that reacts to changes in infrared energy (moving body
heat) within the coverage area. Once the sensor stops detecting
movement and the time delay elapses, lights will go from high to low
mode and eventually to an OFF position if it is desired. Sensors must
directly “see” motion of a person or moving object to detect them, so
careful consideration must be given to sensor luminaire placement and
lens selection. Avoid placing the sensor where obstructions may block
the sensor’s line of sight.
PIR Occupancy Sensor: MSWSFSP221B
PIR Occupancy Sensor Wiring Diagram
Operation During Power-up
During the sensor warm-up period, which can last up to 5 seconds after initial power-up (or after a lengthy power
outage), the load will remain ON until the selected time delay expires.
PIR Occupancy Sensor Installation Instruction
Mounting to a Fixture/Enclosure – Straight Nipple
Note: These installation instructions apply to the following models ONLY.
WPS40BU50XXXX, WPS25BH50XXXX, WPS50BH50XXXX, WPS25BU50XXXX, WPS50BU50XXXX, WPS40BH50XXXX
1. Determine an appropriate mounting location minimizing the electric
light contribution to the sensor’s photocell.
2. If there is no knockout, drill a hole 0.875” (22mm) in diameter through
the sheet metal in the fixture or enclosure.
3. Add the rubber gasket to the nipple, and install the sensor face down.
nsure the rubber gasket touches the surface of the fixture. Install the
nipple nut securely against the fixture to a torque of 25-30 in-lbs to
ensure IP rating is maintained. NOTE: The Outside Fixture Wall thickness
should be no greater than 0.125"(3.18mm)
for optimal sensor mounting and security.

Operating Instructions
MaxLite LED Wall Packs (Cutoff & Standard)
®
© Copyright 2017. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [email protected]
Page: 8
R V: 5/22/17
Optional Remote Control Configuration Tool
The configuration process establishes the appropriate parameters for the MSWSFSP221Boperation. This is done
through the FSIR-100 configuration tool. If no configuration steps are taken, the sensor will use its default parameter
values.
The FSIR-100 Wireless IR Configuration Tool is a handheld tool for changing defaults and testing of MSWSFSP221B.
It provides wireless access to the MSWSFSP221B sensors for parameter changes and testing.
The FSIR-100 display shows menus and prompts to lead you through each process. The navigation pad provides a
simple way to navigate through the customization fields.
Within a certain mounting height of the sensor, the FSIR-100 allows modification of the system without requiring
ladders or tools; simply with a touch of a few buttons.
The FSIR-100 IR transceiver allows bi-directional communication between the MSWSFSP221B and the FSIR-100
configuration tool. Simple menu screens let you see the current status of the sensor and make changes. It can
change sensor parameters such as high/low mode, sensitivity, time delay, cut off, and more. With the FSIR-100
you can also establish and store MSWSFSP221B parameter profiles.
PIR Occupancy Sensor Installation Instruction: MSWSFSP221B (Continued)

Batteries
The FSIR-100 operates on three standard 1.5V AAA Alkaline batteries or three rechargeable AAA NiMH batteries. The
battery status displays in the upper right corner of the display. Three bars next to BAT= indicates a full battery charge.
A warning appears on the display when the battery level falls below a minimum acceptable level. To conserve battery
power, the FSIR-100 automatically shuts off 10 minutes after the last key press.
• If communication is not successful, (if possible) move closer to the sensor.
• If still not successful, there may be too much IR interference from other sources. Programming the unit at night
when there is no daylight available may be the only way to communicate with the sensor.
Operating Instructions
MaxLite LED Wall Packs (Cutoff & Standard)
®
© Copyright 2017. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [email protected]
Page: 9
R V: 5/22/17
PIR Occupancy Sensor Installation Instruction: MSWSFSP221B (Continued)
Navigation
Navigate from one field to another using (up) or (down) arrow keys. The
active field is indicated by flashing (alternates) between yellow text on
black background and black text on yellow background.
Once active, use the Select button to move to a menu or function within
the active field. Value fields are used to adjust parameter settings. They
are shown in “less-than/greater-than” symbols: <value>. Once active,
change them using(left) and(right) arrow keys. The right key increments
and the left key decrements a value. Selections wrap-around if you
continue to press the key beyond maximum or minimum values. Moving
away from the value field overwrites the original value. The Home button
takes you to the main menu. The Back button can be thought of as an undo
function. It takes you back one screen. Changes that were in process prior
to pressing the key are lost.
IR Communication
IR communication can be affected by the mounting height of the sensor and
high ambient lighting such as direct daylight or electric light such as flood-
lights, and some halogen, fluorescent lamps, L D’s.
When trying to communicate with the MSWSFSP221B, be sure to be
positioned under the sensor without any obstructions. very time the
commissioning tool establishes communication with the
MSWSFSP221B, the controlled load will cycle.

© Copyright 2017. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [email protected]
Page: 10
R V: 5/22/17
Operating Instructions
MaxLite LED Wall Packs (Cutoff & Standard)
®
PIR Occupancy Sensor Installation Instruction: MSWSFSP221B (Continued)
FSP-2X1 Screens

© Copyright 2017. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [email protected]
Page: 11
R V: 5/22/17
Operating Instructions
MaxLite LED Wall Packs (Cutoff & Standard)
®
PIR Occupancy Sensor Installation Instruction: MSWSFSP221B (Continued)
FSP-2X1 Screens

Operating Instructions
MaxLite LED Wall Packs (Cutoff & Standard)
®
PIR Occupancy Sensor Installation Instruction: MSWSFSP221B (Continued)
FSP-2X1 Screens
© Copyright 2017. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [email protected]
Page: 12
R V: 5/22/17

Operating Instructions
MaxLite LED Wall Packs (Cutoff & Standard)
®
PIR Occupancy Sensor Installation Instruction: MSWSFSP221B (Continued)
Troubleshooting
© Copyright 2017. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [email protected]
Page: 13
R V: 5/22/17
Lights will not go to High Mode:
• Check all wire connections and verify the load and the ground wires are tightly secured.
• Make sure that the sensor is not obstructed.
• Check light level parameter, to find out the amount of light that the sensor is detecting. Cover the sensor lens to
simulate darkness in the room. If the lights come ON, the setpoint needs to be adjusted. If set for minimum, more
than 1 fc at the sensor of ambient light will cause the lights to be held OFF. See the new settings section for
instructions.
Lights will not go into Low Mode:
• The time delay can be set from a minimum of 30 seconds to a maximum of 30 minutes. nsure that the time delay
is set to the desired delay and that there is no movement within the sensor’s view for that time period.
• To quickly test the unit operation, enable test mode and move out of the sensor’s view. Lights should fade to
low mode after 5 seconds.
Lights will not turn OFF:
• Cut Off time may be set to “None.”
• nsure that the Cut Off is set to the desired time and that there is no movement within the sensor’s view for that
time period when the lights are in Low Mode.
• To quickly test the unit operation, enable test mode and move out of the sensor’s view. Lights should fade to low
mode after 5 seconds, and the OFF (if cut off is enabled) after 10 sec.
Lights do not turn ON:
Check for blinking red L D. If the L D blinks with long pulses, as opposed to short pulses, the sensor has reached
its Hold Off setpoint or Photocell Light Level setpoint.
Lights suddenly turn off and will not come back on:
Check for blinking red L D. If the L D blinks with long pulses, as opposed to short pulses, the sensor has reached
its Hold Off setpoint or Photocell Light Level setpoint.

Operating Instructions
MaxLite LED Wall Packs (Cutoff & Standard)
®
MaxLite Inc. warrants its products for a minimum period of FIVE (5) years from the date of original purchase from
MaxLite or its authorized distributor/dealer (the “Warranty Period”), as follows: If a Product fails to operate during the
Warranty Period as a result of defects in materials or workmanship, MaxLite will, at its option, repair it, replace it with
the same or like Product.
Please refer to Maxlite’s website (at http://maxlite.com/resources/warranties) for the complete
terms and conditions of our warranty.
Limitation of Liability
TH FOR GOING WARRANTY IS XCLUSIV , AND IS TH SOL R M DY FOR ANY AND ALL CLAIMS,
WH TH R IN CONTRACT, IN TORT OR OTH RWIS ARISING FROM TH FAILUR OF PRODUCT AND IS IN
LI U OF ALL OTH R WARRANTI S, XPR SS OR IMPLI D, INCLUDING ALL WARRANTI S OF
M RCHANTABILITY OR FITN SS FOR A PARTICULAR PURPOS , WHICH WARRANTI S AR H R BY
XPR SSLY DISCLAIM D TO TH XT NT P RMITT D BY LAW AND, IN ANY V NT, SHALL B LIMIT D TO
TH WARRANTY P RIOD SP CIFI D ABOV . TH LIABILITY OF MAXLIT SHALL B LIMIT D TO TH T RMS
OF TH XPR SS WARRANTY S T FORTH H R IN. IN NO V NT WILL MAXLIT B LIABL FOR ANY
SP CIAL, INCID NTAL OR CONS QU NTIAL DAMAG S INCLUDING, WITHOUT LIMITATION, DAMAG S
R SULTING FROM LOSS OF US , PROFITS, BUSIN SS OR GOODWILL, LABOR COSTS, R MOVAL OR
INSTALLATION COSTS, D CR AS IN TH LIGHT OUTPUT OF TH LAMP, AND/OR D T RIORATION IN TH
LAMP’S P RFORMANC , WH TH R OR NOT MAXLIT HAS B N ADVIS D OF TH POSSIBILITY TH R OF.
UND R NO CIRCUMSTANC S SHALL MAXLIT ’S NTIR LIABILITY FOR A D F CTIV PRODUCT XC D
TH PURCHAS PRIC OF THAT PRODUCT. WARRANTY S RVIC S PROVID D UND R TH S T RMS AND
CONDITIONS DO NOT NSUR TH UNINT RRUPT D OP RATION OF PRODUCTS; MAXLIT SHALL NOT B
LIABL FOR DAMAG S CAUS D BY ANY D LAYS INVOLVING WARRANTY S RVIC .
This Limited Warranty gives you specific legal rights and you may also have other rights that may vary from state to
state. Because some states or jurisdictions do not allow the exclusion or limitation of liability for consequential or
incidental damages, this limitation may not apply to you.
Warranty Information
© Copyright 2017. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: [phone] Fax: [phone] mail: [email protected]
Page: 14
R V: 5/22/17