Mazda 0000-8L-G03A User manual

GENUINE ACCESSORIES
INSTALLATION INSTRUCTIONS
PART NUMBER: APPLICABLE MODELS:
0000-8L-G03A 2001>Tribute
1999>MPV
Part # 1032597 Rev A Page 1 of 3
IMPORTANT
1. Carry gear in the basket, and attach accessories directly to the LoadWarrior basket (using applicable
accessory instructions.)
2. You may carry bikes or skis, provided you do not
exceed the recommended weight limit for your vehicle.
0
LOAD LIMITS:
▲
basket
contents
REFER TO THE
VEHICLE’S OWNER’S
MANUAL FOR YOUR
MAX. LOAD LIMIT!
DISTRIBUTE YOUR LOAD EVENLY INSIDE THE BASKET.
▲
25 lbs.
(11 kg)
DO NOT EXCEED BASKET CONTENT WEIGHT LIMIT:
REFER TO THE VEHICLE’S OWNER’S MANUAL
FOR YOUR MAX. LOAD LIMIT!
Always tie down long loads at front and rear.
LUGGAGE CARRIERATTACHEMENT
& STRETCH NET

Adjust Your Crossbars
•If you have a TRIBUTE, move crossbars to 26” apart.
• For other vehicles with bars that can be moved, move the bars to 30” apart.
TIGHTEN YOUR CROSSBARS IF YOU LOOSENED THEM.
1
Part # 1032597 Rev A
Position the Support Brackets ABOVE Your Vehicle’s Crossbars
•Place the brackets second slat from each end (except Tribute front,
see illustration) and INSIDE of the basket frame
• Tabs on brackets must face OUTBOARD
• Keep crossbar centered below tab!
It may be necessary to move the bracket to a
new position, or to adjust the basket position.
5
Page 2 of 3
Tribute Only:
26”
30”
Tribute Only:
Assemble the Basket
•Remove the machine screws and washers
from the ends of the LoadWarrior tubes.
• Attach the two basket halves by pushing
the tube ends together.
• Insert screws and washers into tube joints and tighten.
2
Attach Fairing to Either End of Basket
•Pry open the SnapArounds, attach them
to the LOWER FRONT BAR
• Insert bolts through washers, fairing and SnapArounds.
• Attach knobs and TIGHTEN
• NOTE: Fairing can fold down when
carrying long slender loads.
3
Load Basket onto Racks
•Center basket over your rack’s crossbars.
• Do not attach to less stable center
locations (see diagram)
4
A friend
would make
this easier .
(SIDE VIEW)
Do not attach brackets at these locations.
FRONT
In some situations the crossbar may sit off
center of the bail.

Part # 1032597 Rev A
Position the Cover Brackets
•Position the cover brackets onto installed support brackets.
• Hooked tab should cover the larger support bar.
6
Arrow points outboard
to ends of vehicle.
To remove the basket,
do not disassemble the hardware (except Tribute).
•Loosen the knobs until barely attached.
• Unlock the T-bolts and let curved brackets swing freely.
• Remove basket.
TRIBUTE MODELS: completely disassemble hardware to remove basket
Page 3 of 3
Attach Baseplate
TRIBUTE Models:
• Insert wire bail through holes in baseplate.
Other Models:
• Insert bolt into round hole, and T-bolt into slotted hole.
7
TRIBUTE Other Models
Attach the Knobs
•Engage the threads of the bolts
TRIBUTE MODELS SKIP TO STEP 10
8
Secure the Basket to the bars
•Lock the T-bolts
9T-BOLT IS LOCKED
when the “T” of the
bolt is turned inside
the hole:
Tighten Knobs
•Tighten knobs evenly on both sides.
10
Check Installation
•Make sure installation is secure by tugging at basket.
• The basket should not slide on the bars. Tighten knobs if necessary.
11
Tribute Only: